EverFocus EAN Plus Series User manual

EAN Plus Series
IP Box Camera
User’s Manual
* Lens not included.
Copyright © EverFocus Electronics Corp,
Release Date: October, 2012

Copyright 2012 EverFocus Electronics Corp.
All rights reserved. No part of the contents of this manual may be reproduced or transmitted in any form or by
any means without written permission of the EverFocus Electronics Corporation.
EverFocus
12F, No.79, Sec. 1, Shin-Tai Wu Road,
Hsi-Chih, Taipei, Taiwan
TEL: [phone]
FAX: [phone]
www.everfocus.com.tw
October, 2012

Regulatory Notices
About this document
All the safety and operating instructions should be read and followed before the unit is operated. This
manual should be retained for future reference. The information in this manual was current when
published. The manufacturer reserves the right to revise and improve its products. All specifications are
therefore subject to change without notice.
FCC Notice "Declaration of Conformity Information"
This equipment has been tested and found to comply with the limits for a Class
A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful interference
to radio or television reception, which can be determined by turning the equipment off and on, the user
is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
- Consult the dealer or an experienced radio/TV technician for help.
Warning: Changes or modifications made to this equipment, not expressly approved by EverFocus or
parties authorized by EverFocus could void the user's authority to operate the equipment.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause undesired
operation.
EverFocus Electronics Corp.
12F, No. 79, Sec. 1, Shin-Tai Wu Rd., Hsi-Chi,
Taipei Hsien, Taiwan, R.O.C.
EAN Plus-series cameras comply with CE and FCC.

ii
Safety Notice
These limits are designed to provide reasonable protection. This equipment generates, uses and can
radiated radio frequency energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the distance between the equipment and the receiver.
- Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Any changes or modifications not expressly approved by the party responsible for compliance could void
the user's authority to operate the equipment.
To reduce risk of fire or electric shock, do not expose this appliance to rain or moisture.
Do not attempt to disassemble the appliance. To prevent electric shock, do not remove screws or
covers. There are no user-serviceable parts inside. Contact qualified service personnel for maintenance.
Handle the appliance with care. Do not strike or shake, as this may damage the appliance.
Do not use strong or abrasive detergents when cleaning the appliance body. Use a dry cloth to
clean the appliance when it is dirty. When the dirt is hard to remove, use a mild detergent and wipe
gently.
Do not operate the appliance beyond its specified temperature, humidity or power source ratings.
Do not use the appliance in an extreme environment where high temperature or high humidity exists.
Use the appliance at a temperature between 0°C and 50°C / 32°F and 122°F and a humidity level
between 0% and 80% non-condensing. The input power source for this appliance is 12VDC & PoE.
Use only the recommended power supplies. Power supplies must comply with the requirement of
the latest version of IEC60950-1. Substitutions may damage the unit or cause a fire or shock hazard.
Electrostatic-sensitive device. Use proper CMOS/MOSFET handing precautions to avoid
electrostatic discharge.
Installation should be performed by qualified service personnel only in accordance with the
National Electrical Code or applicable local codes.

iii
Terms and Trademark
Ethernet, Internet Explorer, Linux, Microsoft, Windows, WWW are registered trademarks of the
respective holders. Other product names appearing in this User's Guide may be trademarks or registered
trademarks of their respective holders. Java™ and all Java-related logos and trademarks are trademarks
or registered trademarks of Sun Microsystems, Inc. in the United States and other countries.
Support
If the unit ever needs to be repaired or serviced, the customer should contact the nearest EverFocus
Electronics Corp. Service Center for return authorization and shipping instructions.

iv
CONTENTS
1. Introduction ....................................................................................................................................... 1
2. Overview............................................................................................................................................ 2
3. Features ............................................................................................................................................. 3
4. Installation ......................................................................................................................................... 4
4.1 Packing List.......................................................................................................................................4
4.2 I/O Terminal Block ...........................................................................................................................5
4.3 Lens Installation and Adjustment ....................................................................................................5
4.4 Top / Bottom-Mount .......................................................................................................................6
4.5 Basic Connection..............................................................................................................................7
5. Accessing the User Interface............................................................................................................... 8
5.1 Assigning an IP Address ...................................................................................................................8
5.2 Settings for Microsoft Internet Explorer........................................................................................10
5.3 Connecting the Camera to the Network........................................................................................12
5.4 Live View Window..........................................................................................................................14
6. Playback ........................................................................................................................................... 17
6.1 Remote Playback Using Playback Page..........................................................................................17
6.2 Setting up the Playback Function ..................................................................................................19
6.2.1 Preparing the Micro SD Card .............................................................................................19
6.2.2 Testing the Playback Function ...........................................................................................19
6.3 Playing Back Using ARV Viewer .....................................................................................................21
7Settings ............................................................................................................................................ 22
7.1 System Info ....................................................................................................................................22
7.1.1 Information ........................................................................................................................22
7.1.2 Log......................................................................................................................................23
7.2 User Config.....................................................................................................................................24
7.2.1 Live View Config.................................................................................................................24
7.2.2 Recording / Snapshot.........................................................................................................25
7.2.3 Language ............................................................................................................................26
7.3 Network .........................................................................................................................................27

v
7.3.1 Network .............................................................................................................................27
7.3.2 DDNS ..................................................................................................................................29
7.3.3 SMTP / FTP .........................................................................................................................31
7.3.4 HTTPS .................................................................................................................................33
7.3.5 SNMP..................................................................................................................................36
7.3.6 Network Alarm...................................................................................................................36
7.4 Video ..............................................................................................................................................37
7.4.1 Multi Streaming .................................................................................................................37
7.4.2 Camera...............................................................................................................................39
7.4.3 Advanced ...........................................................................................................................41
7.4.4 ROI (Region of Interest) .....................................................................................................48
7.4.5 Privacy Mask ......................................................................................................................49
7.5 Audio ..............................................................................................................................................51
7.6 User ................................................................................................................................................52
7.6.1 User Information................................................................................................................52
7.6.2 IP Address Filter .................................................................................................................54
7.7 Event ..............................................................................................................................................55
7.7.1 Event Settings ....................................................................................................................55
7.7.2 Motion Detection...............................................................................................................58
7.7.3 Tamper Detection ..............................................................................................................59
7.7.4 Alarm I/O............................................................................................................................59
7.7.5 Schedule.............................................................................................................................60
7.8 System............................................................................................................................................61
7.8.1 Date/Time ..........................................................................................................................61
7.8.2 Daylight Saving...................................................................................................................62
7.8.3 SD Card...............................................................................................................................62
7.8.4 Maintenance ......................................................................................................................63
8. Upgrading Firmware Using IP Utility...........................................................................65
9. Specifications ............................................................................................................. 67

EAN Plus Series
1
1. Introduction
The EAN Plus series is a box-type IP camera delivering image quality of up to 3-megapixel. The EAN Plus
series features the Wide Dynamic Range (WDR) function, which can provide clear images even under
back light circumstances where intensity of illumination can vary excessively. A built-in micro SD card slot
and Power over Ethernet (IEEE802.3af) features are also provided. You can power the camera over the
network or by connecting the camera to a 12V DC power supply. The camera also features H.264 /
MJPEG multi-stream output for simultaneous live monitoring and high-resolution recording. Since the
EAN Plus series conforms to ONVIF / PSIA for compatibility with other network video devices, it
interoperates with a wide variety of hardware and software systems. The EAN Plus series is designed for
simple installation and supports all types of indoor mounting applications.
The EAN Plus Series Models
Model Name Megapixel WDR
EAN3120 Plus 1.3 MP Yes
EAN3220 Plus 2 MP Yes
EAN3300 Plus 3 MP No
System Requirements
Before installing, please check that your computer meets the following system requirements.
Operating System Microsoft Windows XP / Vista (32-bit) / 7 (32-bit)
CPU Intel Core2 Duo 2 GHz or higher
RAM
1 GB or more
Additional HD space depends on required local storage of video files,
100 Mbps network card.
Screen Resolution 1024 x 768 pixels or higher, 32-bit pixel color resolution
Software DirectX 9.0c
Microsoft Internet Explorer 7 or higher
Note: For using the Internet Explorer, some settings are required. Please refer to 5.2 Settings for
Microsoft Internet Explorer.

EAN Plus Series
2
2. Overview
234678910
511
1
No. Item Name Descriptions
1 Memory Card Slot Insert a micro SD / SDHC card to store recording data.
2 Power LED Indicates the power is supplied.
3 DC 12V Port Connects to power.
4 Ethernet / PoE Connects to a 10/100 Ethernet or PoE.
5 Reset Button Resets all configurations to factory default.
6 I/O Terminal Block Connects I/O devices.
7 Video Out Connects to a portable monitor for setting the focus and angle of
the camera during initial installation.
8 Audio In Connects to a microphone for audio input. Note that microphones
with external power supplies are required.
9 Audio Out Connects to a speaker for audio output.
10 Light Sensor Detects lights.
11 Auto Iris Lens Connector Plug the Iris control cable to the connector.

EAN Plus Series
3
3. Features
•1/3” Panasonic CMOS sensor (for EAN3120 Plus / 3220 Plus)
1/2.8” Sony CMOS sensor (for EAN3300 Plus)
•Triple streams (stream 1 / 2 / 3 from H.264 or MJPEG)
•Up to 30 fps at 1920 × 1080
Supports 15 fps at 2048 × 1536 (only for EAN3300 Plus)
•Auto Iris control
•Built-in micro SD / SDHC card slot
•Removable IR-cut filter for Day / Night function
•One alarm input and output
•Two-way audio
•TV-out
•Wide Dynamic Range (for EAN3120 Plus / 3220 Plus)
•2D / 3D Dynamic Noise Reduction (DNR)
•Motion detection
•Privacy mask
•DC 12V / PoE

EAN Plus Series
4
4. Installation
4.1 Packing List
•EAN Plus Series Camera (lens not included) x 1
•Software CD x 1
•Quick Installation Guide x 1
•Tool Packet x 1 (contains the following items)
-C-mount lens adapter - ¼-20 UNC thread mounting bracket and 2 screws
-Hexagon wrench - Power pigtail cable
Note: Contact the shipper if any items appear to have been damaged in the shipping process. If any
items are missing, notify your EverFocus Electronics Corp. Sales Representative or Customer Service
Branch. Please also keep the shipping carton for possible future use.

EAN Plus Series
5
4.2 I/O Terminal Block
The I/O terminal block, located on the rear panel of the camera, can be used to develop application
for alarm input and output.
1 2 3 4
Pin Assignment
No. Function No. Function
1 Alarm COM 3 Alarm Input
2 Alarm Output 4 Digital GND
4.3 Lens Installation and Adjustment
You can install either a CS-mount or a C-mount lens into the camera. It is recommended to use a lens
with aperture ratio of F/1.4 or smaller. Please refer to the following reference steps.
C-Mount Lens Adapter
DC Auto Iris Lens Connector
Focus Screw
Zoom Screw
CS-Mount Lens:
1. Remove the cover cap from the camera body.
2. Install the lens into the camera body.
3. Adjust the lens using the Focus / Zoom Screws.
If you are using a DC Auto Iris lens:
1. Remove the cover cap from the camera body.
2. Install the lens into the camera body.
3. Connect the DC cable to the DC Auto Iris Lens Connector.

EAN Plus Series
6
4. When making final focus adjustment, place the ND filter in front of the lens to force the lens iris
to open, and then adjust the lens using the Focus / Zoom Screws.
Note: To use the ND filter, remove the protective sheets from both sides of an ND filter.
5. Lock the Focus Screw and then remove the ND filter.
C-Mount Lens:
1. Remove the cover cap from the camera body.
2. Install the lens into the camera body using the supplied C-mount lens adapter.
3. Adjust the lens using the Focus / Zoom Screws.
Note: Installing a C-mount lens without the C-mount lens adapter may damage the camera sensor.
4.4 Top / Bottom-Mount
You can use the supplied mounting bracket and screw it on the top of the camera body to suspend
the camera, or on the bottom of the camera body to support the camera.
Top Mount
Bottom Mount

EAN Plus Series
7
4.5 Basic Connection
Micro SD
Audio
In Out
Ethernet
(PoE)
DC 12V
Power
Reset
Video Out
COM
Out
In
GND
Alarm
1
2
3
3
4
5
1. Use a standard network cable to connect the camera to the network.
2. Connect the camera to power using one of the following methods:
•Plugging the supplied power pigtail cable to the DC 12V port.
•Using the PoE function and the power will be provided over the network cable.
3. Optionally connect the camera to a speaker or microphone. Note that microphones with
external power supplies are required.
4. Optionally connect the camera to a monitor using a BNC cable.
5. Optionally connect the camera to the input / output devices.
After powering the camera, the power LED will be lit in red and you can access the live view and
adjust the image clarity.

EAN Plus Series
8
5. Accessing the User Interface
This section explains how to access the Web interface of the camera for configuration.
5.1 Assigning an IP Address
You have to assign an IP address for your camera to be accessible. To assign an IP address to the
camera, use the IP Utility (IPU) software included in the software CD. Please connect the IP camera in
the same LAN of your computer.
1. Install and then start the IPU program . The following dialog box appears.
2. Click Find Devices to search the cameras connected in the LAN. The default network values of the
cameras will be displayed. By default, the network protocol of the camera is DHCP.
3. To configure the network settings, select a camera and then click Login/Multi Login to log in.

EAN Plus Series
9
4. Type the user ID and password. Click OK.
Note:
1. The default user ID is user1 and the default password is 11111111.
2. If you select more than one camera that has the same user ID / password, you will be able
to log in several cameras at once.
5. To change the IP address, double-click the IP Address of the camera. Type a new IP address and
then click Set IP Address to save the settings.
You can also change the other settings by double-clicking the values. After configuring the values,
click Save Configuration.
Note: Most networks uses DHCP to assign IP address, if you are unsure of your network
settings, please consult your network administrators for configuration details.
6. To access the camera, highlight the camera and click Connect to Selected IP. The Internet
Explorer window pops up.
7. Type the user ID and password to log in. The Live View window of the camera appears.
Note: You might be required to download ActiveX, which is required to view the camera feed.
If asked, click "Yes". For more details on setting up the Microsoft Internet Explorer, please refer
to 5.2 Settings for Microsoft Internet Explorer.

EAN Plus Series
10
5.2 Settings for Microsoft Internet Explorer
To enable Remove Live View, Firmware Upgrade and ActiveX Prompt on Internet Explorer, some
settings have to be complete. Please follow the steps below:
1. On the computer, click Start > Control Panel > System and Security > Action Center (click Change
User Account Control Settings), the User Account Control Settings window appears. Adjust the
slide bar to Never Notify and then click OK. Restart your computer if requested.
2. Open the Internet Explore, click Tools > Internet Options > Security Tab > Custom Level, the
Security Settings windows appears.

EAN Plus Series
11
3. In the Download unsigned ActiveX controls field, select Prompt. In the Include local directory
path when uploading files to a server field, select Enable. Click OK.
4. In the Internet Options window, click the Advanced tab and then disable Enable memory
protection to help mitigate online attacks. Click OK.

EAN Plus Series
12
5.3 Connecting the Camera to the Network
There are three methods to connect the IP camera to the network: Router or LAN Connection, Direct
High-Speed Connection and One-to-One Connection.
Router or LAN connection
This is the most common connection in which the IP camera is connected to a router and allows
multiple users on and off site to see the IP camera on a LAN/WAN (Internet). The camera must be
assigned an IP address that is compatible with its LAN. By setting up port forwarding on the router,
you can remotely access the cameras from outside of the LAN via the Internet. To remotely access the
Web interface of the IP camera, please refer to 7.3.2 DDNS. To set up port forwarding, please consult
the manual of the router.
Straight-through LAN patch cable
Right: Pinout of a straight-through cable.

EAN Plus Series
13
Direct High-Speed Connection
In a Direct High-Speed Connection, the camera connects directly to a modem without the need for a
router. You need to set the static or dynamic WAN IP address assigned by your ISP (Internet Service
Provider) in the camera’s configuration web pages. To access the camera, just type “http://xxx”,
where xxx is the IP address given by your ISP. If you have a dynamic IP address, this connection may
require that you use DDNS for a reliable connection. Please refer to 7.3.2 DDNS.
One-to-One Connection (Directly from PC to IP Camera)
You can connect directly without using a switch, router or modem. However, only the PC connected
to the camera will be able to view the IP camera. You will also have to manually assign a compatible IP
address to both the computer and the IP camera. Unless the PC has another network connection, the
IP camera will be the only network device visible to the PC. See the diagram below:
Pinout of straight patch cable
Right: Pinout of a crossed-over cable.