EverFocus EZA1280 eZ.HD Series User manual

EZA1280 eZ.HD Series
1080p Dual Power FHD IP66 IR Bullet Camera
User’s Manual
Copyright © EverFocus Electronics Corp.
Release Date: May, 2019
All the images including product pictures or screen shots in this document are for example
only. The images may vary depending on the product and software version. Information
contained in this document is subject to change without notice.
EverFocus Taiwan:
2F., No.12, Ln. 270, Sec. 3, Beishen Rd., Shenkeng Dist., New Taipei City 222, Taiwan
TEL: [phone] FAX: [phone] www.everfocus.com.tw

1. Introduction
Equipped with a 1080p Sony STARVIS CMOS sensor, the EZA1280 deliver
1080p full HD image quality. The model provides 2.8-12mm lens with ICR.
Featured with Digital Wide Dynamic Range (D-WDR), the camera can
provide clear images even under backlight circumstances where intensity
of illumination can vary excessively. The EZA1280 supports dual power
(12VDC / 24VAC) and supports both NTSC and PAL scanning systems.
1.1 Packing List
Camera x 1
Mounting Sticker x 1
L-Type Wrench x 1
Screw & Screw Anchor x 3
User Manual x 1
1.2 Features
1080p Sony STARVIS CMOS sensor, delivering amazing high sensitivity
Varifocal 2.8-12mm with ICR to capture the desired field of view
Extended IR range of up to 40m / 131ft. with 4 LEDs (depends on
scene IR reflectivity)
D-WDR to improve the visibility under high contrast scene
3-Axis rotation design allows wall or ceiling mounting
IP66-rated with metal housing
Supports dual power (12VDC / 24VAC)
Supports UTC function: Control camera OSD settings directly from
DVR end

2
1.3 Dimensions
1.4 Optional Accessory
BAE3201
Color: White
Size: Φ138 x 54(H)mm / 5.43”x2.16”
Weight: 700g / 1.87lb
Material: Metal
1.5 Cable Description
Power Cable
Video Output Cable
1
2
No. Name Descriptions
1 Power Cable Connects to a 12VDC / 24VAC power source.
2 Video Output
1080p output, using a 75 Ohm BNC-type coaxial
cable.

3
2. Installation
1. Stick the supplied Mounting Sticker to the surface to mark the 3 screw
positions. Drill 3 holes on the surface and insert the supplied 3 Screw
Anchors into the screw holes. If you want to run the cable through the
surface, drill a hole within the 3 screw area.
2. To mount the camera to the surface, screw the Camera Base to the
surface using the supplied 3 Screws.
Mounting
Surface
Screws Screw Anchors
Camera Base
3. Connect the Power Cable to a 12VDC / 24VAC power source. Connect
the Video Output Cable to a monitor or DVR.
4. You can use the Joystick on the cable to configure camera OSD settings
or switch to different video formats. Remove the Protection Cap from
the Joystick before using it.
UP
DN
Switching Video Format:
•Push the joystick up for 5 sec. to switch to
AHD.
•Push the joystick right for 5 sec. to switch to
TVI.
•Push the joystick down for 5 sec. to switch to
CVI.
•Push the joystick left for 5 sec. to switch to
CVBS.
Configuring OSD Settings:
•Push the Joystick up / down to select among
menu items.
•Push the Joystick left / right to adjust the level
of the selected item.
•Press the Joystick to enter the submenu or
exit the OSD Setup Menu.

4
5. For the first time installation, check whether the camera is properly
focused. If not, you can manually adjust camera Zoom or Focus using
the supplied L-Type Wrench. On the bottom of the camera, find the
Zoom and Focus nuts. Using the supplied L-Type Wrench to adjust
camera Zoom or Focus.
Z
OO
M
F
O
C
U
S
6. You can optionally adjust camera angles. To do so, loosen the Tilt Screw
or Rotate Screw on the bracket using the supplied L-Type Wrench to
adjust camera angles. After adjusting camera angles, tightly screw back
the Tilt/Rotate screws.
Tilt Screw
Rotate Screw
3. Configuration in the OSD Menu
You can configure camera settings in the OSD menu from DVR end.
No Main
Sub
Menu
Sub Menu / Function
1
Iris
ELC
2 Focus Adj.
Off
On
Focus Area
Wide / Narrow / Middle
DISP Tone
0-2
DISP H_POS
0-60
DISP V_POS
0-34
DISP H_Size
0-60
DISP V_ Size
0-34
3
Exposure
Brightness
0-20

5
Shutter
Auto
Normal / Deblur
Manual Speed
1/30, 1/60, 1/1 20, 1/2 40, 1/4 80,
1/1000, 1/2000, 1/4000, 1/8000,
1/1 5000, 1/30000
Flicker
Sens-Up
Off, x2, x4, x8, x16, x32
AGC
0-10
4 Backlight
Off
HLC
Mode
Night Only / All Day
Level
0-20
Color
BLK / CUSTOMIZE / WHT / YEL / CYN / GRN
/ MAG / RED / BLU
BLC
H-POS
0-20
V-POS
0-20
H-Size
0-20
V-Size
0-20
WDR Mode
Normal
ROI
Window Zone
0-3
Window Use
On / Off
H-POS
0-1920
V-POS
0-1080
H-Size
0-1920
V-Size
0-1080
Weight
Middle / High / Low
5Day&Night Auto Mode
Auto
IR LED
On / Off
Anti-Sat.
0-20
LED Power
Dimming
AGC Thres
0-20
AGC Margin
0-20
Delay
Middle / High /
Low
Color
White LED
On / Off
Anti-Sat.
0-20
LED Power
Dimming
AGC Thres
0-20
AGC Margin
0-20
Delay
Middle / High /
Low
B&W
IR LED
On / Off
Anti-Sat.
0-20
LED Power
Dimming
AGC Thres
0-20
AGC Margin
0-20
Delay
Middle / High /
Low
Extern
IR LED
On / Off
Anti-Sat.
0-20
LED Power
Dimming
Extern SW
High / Low

6
D > N Thres
0-20
N > D Thres
0-20
Delay
Middle / High /
Low
6 Color AWB
Auto
Autoext
Preset
Manual
C-Temp
3000K / 5000K / 8000K
R-Gain
0-20
B-Gain
0-20
Color Gain
0-20
7
DNR
Middle / High / Off / Low
8 Image
Sharpness
CVBS
0-10
CVI
0-10
TVI
0-10
AHD
0-10
Gamma
0.45 / 0.55 / 0.65 / 0.75
Mirror
On / Off
Flip
On / Off
ACE
Off / Low / Middle / High
Defog
Off
On
Mode
Manual / Auto
Level
Low / Middle / High
Privacy
Off
On
Zone Num
0-15
Zone DISP
On / Off
H-POS
0-60
V-POS
0-34
H-Size
0-60
V-Size
0-34
Y-Level
0-20
CB Level
0-20
CR Level
0-20
Trans
0 / 1 / 2 / 3
9 Motion
Off
On
Det
Window
Window Zone
0 / 1 / 2 / 3
Window Use
On / Off
Det H-POS
0-60
Det V-POS
0-34
Det H-Size
0-60
Det V-Size
0-34
Det Tone
0 / 1 / 2 / 3 / 4
Mdrect Fill
On / Off
Sensitivity
0-10
Motion OSD
On / Off
Text Alarm
On / Off
Signal Out
On / Off
10
System
Output
HD Output
Off / CVBS / CVI / TVI / AHD

7
Mode
Frame Rate
1080 25P(30P) / 720 25P(30P) / 720
50P(60P)
Freq.
50HZ / 60HZ
Confirm
YES
Image
Range
Full
Comp
User
Offset
0-32
Color
Space
HD-CbCr / YUV / SD-CbCr
Color Bar
On / Off
Language
ENG / CHN / CHN(S) / JPN / KOR / POR
Cam Title
Off
Right Up
Left Down
Reset