EverFocus EBH5201 Technical manual

Operation Instruction
HDcctv 1080p
Indoor Compact Bullet Camera
EBH5201
EBH5201-006
EBH5201

EVERFOCUS ELECTRONICS CORPORATION
Operation Instruction
© 2013 EverFocus Electronics Corp
Please read this manual rst for correct installation and operation. This manual should be
retained for future reference. The information in this manual was current when published.
The manufacturer reserves the right to revise and improve its products. All specications are
therefore subject to change without notice.
All rights reserved. No part of the contents of this manual may be reproduced or transmitted in
any form or by any means without written permission of the EverFocus Electronics Corporation.
3

4
PRECAUTIONS
1. Do not install the camera near electric or magnetic elds.
Install the camera away from TV/radio transmitters, magnets, electric motors, transformers and audio speakers
since the electromagnetic elds generated from these devices may distort the video image or otherwise
interfere with camera operation.
2. Never disassemble the camera beyond the recommendations in this manual nor
introduce materials other than those recommended herein. Improper disassembly or
introduction of corrosive materials may result in equipment failure or other damage.
3. Try to avoid facing the camera toward the sun. In some circumstances, direct sunlight may
cause permanent damage to the sensor and/or internal circuits, as well as creating unbalanced illumination
beyond the capability of the camera to compensate.
4. Keep the power cord away from water and other liquids and never touch the power
cord with wet hands. Touching a wet power cord with your hands or touching the power cord with wet
hands may result in electric shock.
5. Never install the camera in areas exposed to oil, gas or solvents.
Oil, gas or solvents may result in equipment failure, electric shock or, in extreme cases, re.
6. Cleaning
For cameras with interchangeable lenses, do not touch the surface of the sensor directly with the hands. Use
lens tissue or a cotton tipped applicator and ethanol to clean the sensor and the camera lens. Use a damp
soft cloth to remove any dirt from the camera body. Please do not use complex solvents, corrosive or abrasive
agents for cleaning of any part of the camera.
7. Do not operate the camera beyond the specied temperature, humidity or power source ratings.
This camera is suitable for indoor operation. Use the camera at temperatures within -10°C~50°C (14°F~122°F) and
in an indoor environment; this device is not rated as weather proof. The input power source is 12VDC. The use of
properly fused or Class 2 power limited type supplies are highly recommended.
8. Mounting
Use care in selecting a solid mounting surface which will support the weight of the camera plus any wind,
snow, ice or other loading, and securely attach the camera to the mounting surface using screws and anchors
which will properly support the camera. If necessary (e.g. when mounting to drop ceilings) use a safety wire to
provide additional support for the camera.

5
ATTENTION! This is a class A product which may cause radio interference in
a domestic environment; in this case, the user may be urged to take adequate
measures.
Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment o and on, the user is encouraged
to try to correct the interference by one of the following measures :
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit dierent from that to which the
receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: Any changes or modications not expressly approved by the
party responsible for compliance could void the users’ authority to operate this
equipment.

Table of Contents
1. PRODUCT OVERVIEW ................................................................. 7
1.1 FEATURES .............................................................................................. 7
1.2 ACCESSORY PARTS LIST ..................................................................... 8
1.3 SPECIFICATIONS ................................................................................... 9
1.4 DIMENSIONS .......................................................................................... 10
2. CAMERA COMPONENT DESCRIPTION ...................................... 11
3. INSTALLATION ............................................................................. 12
4. OSD Structure.............................................................................. 14
6

1. Product Overview
The EBH5201 is an HDcctv indoor bullet camera with Digital Day/Night capability in a compact housing only 1.77" in
diameter and less than 4" long. Based on a 1/3”Panasonic 2.1 megapixel progressive scan sensor and wide angle 2.45mm
megapixel lens for HD 1080p resolution 100% digital images, it delivers vastly superior video quality compared to
traditional CCTV images. This superior resolution not only captures more critical evidentiary information, but the inherent
ability for megapixel video also extends the area of coverage, expedites completion of investigations, resolves complaints
and reduces both capital and operational costs. Designed with 4X Digital Slow Shutter low light enhancement technology,
the EBH5201 can captures color images in low light without ghosting, or it can switch to monochrome mode automatically
in low light environments.
This highly advanced imaging system also incorporates state of the art optical enhancement technologies: Lens Shading
Correction compensates to eliminate articial shadows caused by attenuation of light as it traverses the outer portions
of the lens; Digital Slow Shutter low light enhancement for optimal low light sensitivity combines with Digital Noise
Reduction (DNR) to maximize image clarity while conserving DVR disk storage space; digital zoom with electronic PTZ to
ne tune eld of view; Highlight Suppression (HSBLC) to handle imbalamce due to bright spots in the scene; image ip/
rotate, and much more.
No major upgrade to the IT network is required to deploy this powerful technology; HDcctv cameras communicate at
digital speeds up to 1.5Gb/s over existing or new coaxial cable (RG59 or other types for longer distances), using industry
standard BNC connectors. With its NTSC/analog secondary output to allow convenient aim and focus using a standard
hand held test monitor, full OSD controls, and 94° wide horizontal viewing angle megapixel lens the EBH5201 delivers
exible, robust coverage in a wide range of low light surveillance applications while delivering stunning HD image quality
1.1 Features
• HDcctv 2.1 Megapixel real time 1920x1080/1280x720 HD video over coax for superlative image detail
• Supports video outputs of 1080p30/25 and 720p60/50 (Field Select)
• Choice of Day/Night operation or Full Color Images in Low Light
• Provides DNR to improve picture clarity while enabling DVRs to improve disk storage utilization
• Flexible mounting and positioning - mount included, or ts any 1/4"-20 mount
• SD TV out for aim and focus using standard hand held test monitor
• 2.45mm megapixel lens captures a 94° wide horizontal eld of view
• Easy to use OSD setup menu with an array of options
• Enhanced low light sensitivity through a sensitivity increase setting of up to 4x
• Lens Shading Compensation osets diminished light transmission through lens periphery
for uniform image illumination
• HSBLC [Highlight Suppression Back Light Compensation] to suppress imbalance due to bright areas in the scene
• Digital zoom increases eective lens magnication up to 20x
• Up to 30 Privacy Zones
• Dead pixel compensation for increased clarity and extended service life
7
Chapter
1

8
1.2 Accessory Parts List
Please be careful when you unpack the box due to the electronics devices inside.
Check and make sure that you have all the items listed below inside the original box:
Camera Mounting Bracket
Manual Screws Service Video Cable
Please Note: If an item appears to have been damaged in shipment, replace it properly in its carton and notify the
shipper. If any items are missing, notify your EverFocus Electronics Corp. Sales Representative or Customer Service. The
shipping carton is the safest container in which the unit may be transported. Save it for possible future use.

9
1.3 Specications
Pickup Device 1/3” Panasonic 2.1 Megapixel Color Progressive CMOS sensor
Image Pixels 1920(H)x1080(V) with 2.75μx 2.75μ pixel size
HDcctv Image Area Dimensions 5.28mm (H) x 2.97 mm(W); ø 6.06 mm area diagonal
Sensitivity 0.1 lux/F1.2 (DSS OFF)
S/N Ratio More than 50dB
Video Format Main Output HDcctv
Video Resolution/Mode Main Output Field Select 1080p30/25, 720p60/50
Main Output Connector BNC-F
Video Format Test Output NTSC/PAL Selectable
Test Output Connector Pin connector on board; adapter to BNC supplied
Lens Type 2.45mm Fixed Focal Length
FOV Angle 94°Horizontal
Shutter Speed Auto / Manual Selectable
OSD Yes (5-axis joystick control)
D/N Mode Auto, Color, B/W (Electronic D/N)
Exposure Control Automatic Electronic Shutter
DSS Low light boost 2X, 3X, 4X
Lens Shading Compensation On / Off
Auto Gain Control Variable 0~23dB (23bD=200x)
White Balance ATW/Push/Manual/Outdoor/Indoor
DNR Low / Medium / High
HSBLC On / Off
Digital Zoom 1X ~20X
Power Source & Consumption DC12V (+/-10%) @ 160mA
Image Flip Off/V Flip/H Flip/H+V Flip (Rotate)
Programable Privacy Zones 30 areas independently adjustable for size, location, color
Weight 136.1g/408oz (Camera Only; Mount adds 113.4g/4oz)
Dimensions
Body: 86.7mm/3.41"(L) x Ø44mm/Ø1.77" Diameter(W)
Mount: Ø60mm/Ø2.36" Diameter(W)
[Adds 97.6mm/3.84" max to height]
Operating Temperature -10°C~50°C ; 14°F~122°F
Operating Humidity 20%~80% humidity, non-condensing
Certications FCC/CE

10
1.4 Dimensions
Inches:
MOUNTING HOLE (Top/Bottom)
(1/4"-20 UNC, Depth 0.17")
MOUNTING HOLE (Top/Bottom)
(1/4"-20 UNC, Depth 0.17")
2.95"
Ø1.77"
3.81"
Ø2.36"
0.1"-Ø0.14"
1.63"
1.41"
3.45"

11
2. Camera Component Description
Chapter
2
OSD Control Joystick
Service Video Connector
HDcctv Out BNC
Power LED
DC12V Input
+-

12
3. Installation
Chapter
3

When installing the camera, make sure that all cable ends and connectors
are protected from humidity and other outdoor environments.
13
* NOTE
Connections
DC12V In
BNC Female
(HDcctv Jack)
DC12V
Adapter
HDcctv DVR or other
HDcctv Signal Equipment
NTSC Video In
*Service Video Connector Handheld
Monitor
Test Cable
EBH5201

14
Chapter
4
4. OSD Structure
Main Sub Menu Sub Menu
SETUP
EXPOSURE
BRIGHTNESS 0 ~ 20
SHUTTER MODE AUTO, MANUAL
SHUTTER
SPEED
1/30(25), 1/60(50), 1/120(100), 1/250, 1/700, 1/1K,
1/1.6K, 1/2.5K, 1/5K, 1/7K, 1/10K, 1/30K.
DSS
(Digital Slow Shutter) OFF, X2, X3, X4.
AGC MAX 0 ~ 23dB
INITIAL
RETURN
WHITE BALANCE
WB MODE AUTO / PUSH LOCK / MANUAL
CHROMA 0 ~ 20
KELVIN LOW, MIDDLE, HIGH
RED GAIN 0 ~ 20
BLUE GAIN 0 ~ 20
PUSH AUTO -
INITIAL
RETURN
BLC
MODE OFF, BLC
BLC OSD OFF, ON
BLC X - POSITION 0 ~ 20
BLC Y - POSITION 0 ~ 20
BLC X - SIZE 0 ~ 20
BLC Y - SIZE 0 ~ 20
INITIAL
RETURN
DAY & NIGHT
D&N MODE AUTO, COLOR, BW
DWELL TIME 1sec ~ 10sec
AGC THRS 0 ~ 20
MARGIN 0 ~ 20
INITIAL
RETURN
IMAGE
SHARPNESS 0 ~ 10
MIRROR OFF, ON
FLIP OFF, ON
DZOOM(Digital Zoom) 1X ~ 20X
SHADING (LSC) OFF, ON
HLMASK (HSBLC) OFF,ON
HLMASK LEVEL 0 ~ 20
HLMASK COLOR WHITE, YELLOW, CYAN, GREEN
MAGENTA, RED, BLUE, BLACK
INITIAL
RETURN
Image
DNR OFF, LOW, MIDDLE, HIGH
INITIAL
RETURN

15
4. OSD Structure
Main Sub Menu Sub Menu
SPECIAL
CAM TITLE
CAM TITLE
0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K
L M N O P Q R S T U V W X Y Z ! - () < >
SPA > > < < BAK
LOCATION
RETURN
LANGUAGE ENGLISH, RUSSIAN, SPANISH,
GERMAN, FRENCH, PORTUGUESE
PRIVACY
OFF, ON ZONE NO 0 ~ 29
MASK MODE OFF, ON
X - POSITION 0 ~ 60
Y - POSITION 0 ~ 40
X - SIZE 0 ~ 40
Y - SIZE 0 ~ 40
COLOR
BLACK, WHITE, YELLOW, CYAN, GREEN,
MAGENTA,
RED, BLUE
TRANSPARENCY 100%,75%,50%,25%,0%
INITIAL
RETURN
MOTION DETECT
OFF, ON RESOLUTION 0 ~ 4
SENSITIVITY 0 ~ 20
WINDOW USE ON, OFF
WINDOW TONE 1 ~ 6
X-POSITION 0 ~ 60
Y-POSITION 0 ~ 40
X-SIZE 0 ~ 60
Y-SIZE 0 ~ 40
INITIAL
RETURN
DISPLAY
CAM TITLE OFF, ON
MOTION DETECT OFF, ON
ZOOM OFF, ON
INITIAL
RETURN
SYSTEM
SHADING DET OFF, ON
DEFECT DET OFF, ON
DOUT FORMAT 720P, 1080P
DOUT FPS 50, 60 / 25, 30
COLOR BAR OFF, ON
INITIAL
RETURN
FACTORY
DEFAULT
EXIT

EverFocus Electronics Corp.
EverFocus Taiwan:
12F, No.79, Sec. 1, Shin-Tai Wu Road,
Hsi-Chih, Taipei, Taiwan
TEL: [phone]
FAX: [phone]
www.everfocus.com.tw
[email protected]
EverFocus Europe - Germany:
Albert-Einstein-Strasse 1, D-46446
Emmerich, Germany
TEL: [phone]
FAX: [phone]
www.everfocus.de
[email protected]
EverFocus China - Beijing:
Room 609, Technology Trade Building,
Shangdi Information Industry Base,
Haidian District, Beijing 100085, China
TEL: [phone]~39
FAX: [phone]
www.everfocus.com.cn
[email protected]
EverFocus China - Shenzhen:
4F, No. 2, D4 Building, Wan Yelong
Industrial Park, Tangtou Road, Shiyan,
Baoan, Shenzhen, Guangdong 518101, China
TEL: [phone]
FAX: [phone]
www.everfocus.com.cn
[email protected]
EverFocus USA - California:
1801 Highland Avenue, Unit A, Duarte, CA 91010, USA
TEL: [phone]
FAX: [phone]
www.everfocus.com
[email protected]
EverFocus USA - New York:
415 Oser Avenue, Unit S, Hauppauge, NY 11788, USA
TEL: [phone]
FAX: [phone]
www.everfocus.com
[email protected]
EverFocus Japan:
5F, Kinshicho City Building, 2-13-4 Koto-Bashi,Sumida-Ku,
Tokyo, 130-0022, Japan
TEL: [phone]
FAX: [phone]
www.everfocus.co.jp
[email protected].jp
EverFocus Europe - UK:
Unit 12, Spitfire Business Park,
Hawker Road, Croydon Surrey, CR0 4WD, UK
TEL: [phone]
FAX: [phone]
www.everfocus.com
[email protected]
EverFocus India:
Suite 803, Housen Bhavan, C-21,
Bandra Kurla Complex, Bandra (East),
Mumbai 400051, India
TEL: [phone]
FAX: [phone]
www.everfocus.in
[email protected]
Your EverFocus product is designed
and manufactured with high quality
materials and components which can
be recycled and reused.
This symbol means that electrical and
electronic equipment, at their end-of-
life, should be disposed of separately
from your household waste.
Please, dispose of this equipment at
your local community waste
collection/recycling centre.
In the European Union there are
separate collection systems for used
electrical and electronic product.
Please, help us to conserve the
environment we live in!
Ihr EverFocus Produkt wurde
entwickelt und hergestellt mit qualitativ
hochwertigen Materialien und
Komponenten, die recycelt und wieder
verwendet werden können.
Dieses Symbol bedeutet, dass
elektrische und elektronische Geräte
am Ende ihrer Nutzungsdauer vom
Hausmüll getrennt entsorgt werden
sollen.
Bitte entsorgen Sie dieses Gerät bei
Ihrer örtlichen kommunalen
Sammelstelle oder im Recycling Centre.
Helfen Sie uns bitte, die Umwelt zu
erhalten, in der wir leben!