EverFocus EMD990F User manual

EMD990F
1080p FHD Mobile IR Mini Dome Camera
User’s Manual
Copyright © EverFocus Electronics Corp,
Release Date: December, 2018
All the images including product pictures or screen shots in this document are for example only. The images may
vary depending on the product and software version. Information contained in this document is subject to change
without notice.

Precautions
1. Do not install the camera near electric or magnetic fields. Install the camera away from
TV/radio transmitters, magnets, electric motors, transformers and audio speakers since the
electromagnetic fields generated from these devices may distort the video image or otherwise
interfere with camera operation.
2. Never disassemble the camera beyond the recommendations in this manual nor introduce
materials other than those recommended herein. Improper disassembly or introduction of
corrosive materials may result in equipment failure or other damage.
3. Try to avoid facing the camera toward the sun. In some circumstances, direct sunlight may
cause permanent damage to the sensor and/or internal circuits, as well as creating unbalanced
illumination beyond the capability of the camera to compensate.
4. Keep the power cable away from water and other liquids and never touch the power cord
with wet hands. Touching a wet power cord with your hands or touching the power cord with
wet hands may result in electric shock.
5. Never install the camera in areas exposed to oil, gas or solvents. Oil, gas or solvents may result
in equipment failure, electric shock or, in extreme cases, fire.
6. Cleaning. For cameras with interchangeable lenses, do not touch the surface of the sensor
directly with the hands. Use lens tissue or a cotton tipped applicator and ethanol to clean the
sensor and the camera lens. Use a damp soft cloth to remove any dirt from the camera body.
Please do not use complex solvents, corrosive or abrasive agents for cleaning of any part of the
camera.
7. Do not operate the camera beyond the specified temperature, humidity or power source
ratings. This camera is suitable for indoor operation only. Use the camera at temperatures
within -20°C~50°C (-4°F~122°F) and humidity less than 80%; this device is not rated as
submersible. The input power source is 12VDC. Be sure to connect the proper + / - polarity and
voltage, as incorrect polarity or too high a voltage will likely cause the camera to fail, and such
damage is not covered by the warranty.
8. Mounting. Use care in selecting a solid mounting surface which will support the weight of the
camera plus any wind, snow, ice or other loading, and securely attach the camera to the
mounting surface using screws and anchors which will properly support the camera. If
necessary (e.g. when mounting to drop ceilings) use a safety wire to provide additional support
for the camera.

Safety Notice
Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class A digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
- Consult the dealer or an experienced radio/TV technician for help.
FCC Caution:Any changes or modifications not expressly approved by the party responsible for
compliance could void the user's authority to operate this equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.

1
1. Introduction
Equipped with a 1080p Sony Starvis CMOS sensor, the EMD990F is one of the EverFocus eZ.HD
series cameras, providing 1080p full HD image quality. Featured with True Wide Dynamic Range
(T-WDR) function, the camera can provide clear images even under backlight circumstances where
intensity of illumination can vary excessively. The EMD990F supports both NTSC and PAL scanning
systems and is IP68 certified. The 6 IR LEDs enable night vision up to 10m (~33ft.). EMD990F is the
ideal solution for your mobile surveillance needs.
1.1 Packing List
1.2 Features
1080p Full HD with high flexibility and performance for astounding image
Adopts Sony Starvis CMOS sensor, delivering amazing high sensitivity
Astounding image quality from the 2.8mm lens
Extended IR range up to 10m / 33ft. with 6 LEDs (depends on scene IR reflectivity)
True-WDR to improve the visibility under high contrast scene
Supports 3D-Noise Reduction function
Flexible angle viewing with 3-Axis rotation design
Supports UTC function: Control camera OSD settings directly from DVR end
2. Cable Description
No.
Name
Descriptions
1
Power Cable
Connects to a 12VDC power source.
2
Video Output
1080p output, using a 75 Ohm BNC-type coaxial cable.
3 DC Power Pigtail Cable
Optional power pigtail cable. The red wire is positive (+);
while the black wire is negative (-).

Camera x 1

Screw + Plastic Anchor x 3

User Manual x 1

DC Power Pigtail Cable x 1

Hexagon Wrench x 1

Installation Sticker x 1

2
3. Installation
3.1 Installation and Adjustment
1. Stick the supplied Installation Sticker on the position where you want to mount the
camera. Drill three holes through the marks on the Installation Sticker and insert the
supplied three Anchors. Drill another hole within the area of the Installation Sticker only if
you want to wire the cables through the surface.
2. Loosen the two screws using the supplied Hexagon Wrench and then remove the base
plate from the camera.

3
3. Screw the camera base plate to the surface using the supplied three Screws.
4. Screw the camera body back to the base plate using the supplied Hexagon Wrench. You
can wire the cables from the side of camera, or through the surface. Please see the image
below.
Wire the Cables from the Side Wire the cables through
of the camera base the surface
Remark: Do not screw the camera too tight at this stage as you will have to adjust the
camera angle later.

4
5. Connect the camera to the 12VDC power source using the supplied DC Power Pigtail Cable
or power adapter. Connect the video-out cable to the monitor.
6. Adjust the camera angle by rotating the camera body. After adjusting the camera angle,
tighten the two screws on both sides of the camera using the supplied Hexagon Wrench.
Camera Body
Screw
Screw

5
4. Configuration in the OSD Menu
You can configure camera settings in the OSD menu from DVR end. OSD menu structure is listed on
the below table:
No.
Main
Sub Menu
Sub Menu / Function
1
Lens
Manual
2 Exposure
Shutter
NTSC: 1/30, 1/60, FLK, 1/240, 1/480, 1/1000, 1/2000, 1/5000,
1/10000, 1/50000, X2, X4, X6, X8, X10, X15, X20, X25, X30, Auto
PAL: 1/25, 1/50, FLK, 1/200, 1/400, 1/1000, 1/2000, 1/5000,
1/10000, 1/50000, X2, X4, X6, X8, X10, X15, X20, X25, X30, Auto
AGC
0-15
Sens-up
Off
Auto
Sens-up
X2, X4, X6, X8, X10, X15, X20, X25, X30
Brightness
1-100(50 default)
D-WDR
Off
On
Level
0-8
Auto
Defog
Off
Auto
Pos/Size
Position, Size,↑,↓,→,←
Gradation
0-2
Default
3 Backlight
Off
BLC
Level Middle, High, Low
Area
Position, Size,↑,↓,→,←
Default
HSBLC
Select
Area1, Area2, Area3, Area4
Display
Off
On
Position, Size,↑,↓,→,←
Black Mask
On/Off
Level
0-100
Model
All Day
Night
AGC Level
0-255
Default
WDR
Level 0-4
D&N Mode
Off / Auto
4 White
Balance
ATW
AWC→SET
Indoor
Outdoor
Manual
Blue
0-100

6
Red 0-100
AWB
5 Day &
Night
Ext
D→N(Delay)
0-60
N→D(Delay)
0-60
Auto
D→N(CDS)
1-255
D→N(Delay)
0-60
N→D(CDS
1-255
N→D(Delay)
0-60
Color
B/W
Burst
Off/On
IR Smart
Off
On
Level
0-15
Area
Position, Size,↑,↓,→,←
6 NR
2DNR
Middle/Low/Off/High
3DNR
Middle/Low/Off/High
7 Special
Cam Title
Off
On 0123456789ABCDEFGHIJKLMNOPQRSTUVWXYZ▶→
←↑↓()ˉ-_▊/=&:~,.
D-effect
Freeze
Off/On
Mirror Off, Mirror, V-flip, Rotate
Neg. Image
Off/On
Motion
Off
On
Select
Area1,Area2,Area3,Area4
Display
On
Position, Size,↑,↓,→,←
Off
Sensitivity
0-100
Color
Green, Blue, White, Red
Trans
1.00,0.75,0.50,
0.25
Alarm
View Type
Off, Block, Outline, All
OSD View
On/Off
Alarm Out
On/Off
Time
0-15
Default
Privacy
Off
On
Select
Area1,Area2,Area3,Area4
Display
Off
Color
Position, Size,↑,↓,→,←
Mosaic Position, Size,↑,↓,→,←
Inv
Position, Size,↑,↓,→,←

7
Color White, Black, Red, Blue, CYAN, Yellow,
Green, User
Trans
1.00,0.75,0.50,
0.25
Default
Language
ENG/CHN1/CHN2/GER/FRA/ITA/SPA/POL/RUS/POR/NED/TUR/KOR/
JPN/HEB/ARB
Defect
Live DPC
Off
On
AGC level
0-255
Level
0-100
White DPC
Off
On
Pos/Size
Position, Size,↑,↓,→,←
Start
Close the iris then press
DPC View
Off/On
Level
0-60
AGC
0-14
Sens-up
x2, x4, x6, x8,x10, x15, x20,
x25, x30
Black DPC
Off
On
Pos/Siz
Position, Size,↑,↓,→,←
Start
Press Enter
DPC View
Off/On
Level 0-100
RS485
CAM ID
0-255
ID Display
Off/On
Baud Rate
2400,4800,9600,19200 ,38400
8 Adjust
Sharpness
Off
Auto
Level
0-10
Start AGC
0-255
End AGC
0-255
Monitor
Gamma User,0.45,0.50,0.55,0.60,0.65,0.70,0.75,0.80,0.85,
0.90, 0.95,1.00
Blue Gain
0-100
Red Gain 0-100
LSC
Off/On
Video.
Out PAL/NTSC
9
Exit
Save& END /Reset/Not Save

8
5. Specification
Model Name EMD990F
Pickup Device 1080p Sony Starvis CMOS sensor
Video Format NTSC / PAL
Effective Pixels 1920 (H) x 1080 (V)
Scanning System Progressive Scan
Sensitivity 0 Lux with IR On
Electronic Shutter Auto / Manual (x30 ~ 1/50,000)
Gamma Correction 0.45 ~ 100
Lens Type 2.8mm fixed lens
FOV H=120°, V=80°, D=140°
BLC OFF / BLC / HSBLC / WDR Selectable
AGC 0 ~ 15 Levels
White Balance ATW / AWC-SET / Indoor / Outdoor / Manual / AWB
Sync Mode Internal
Day/Night Ext, Auto, Color, B/W
IR LED 6 Units
IR Distance Up to 10m / 33ft. (depends on scene IR reflectivity)
S/N Ratio >50dB (AGC off)
OSD Languages English / Simplified Chinese / Traditional Chinese / German / French /
Italian / Spanish / Polish / Russian / Portuguese / Netherlands /
Turkish / Korean / Japanese / Hebrew / Arabic
DNR 2DNR / 3DNR, Off
DEFOG Off / Auto
T-WDR On / Off / Auto (120dB)
Sens-up Off / Auto (x2 ~ x30)
Mirror Off / Mirror / V-Flip / Rotate
Motion Detection Off / On for 4 selectable zones
Privacy Mask Off / On for 4 selectable zones
Environment IP68 Weather Resistant
Power Source 12VDC
Power Consumption 2W max.
Operating Temperature -20°C ~ 50°C / -4°F ~ 122°F
Humidity Less than 80%
Dimensions 58.4 x 60.1mm / 2.3" x 2.4"
Weight 160g / 0.35lb
Certifications CE, FCC, RoHS

9
EverFocus Electronics Corp.
EverFocus Taiwan:
2F., No.12, Ln. 270, Sec. 3, Beishen Rd.,
Shenkeng Dist., New Taipei City 222, Taiwan
TEL: [phone]
FAX: [phone]
www.everfocus.com.tw
mark[email protected]
EverFocus China - Shenzhen:
3F,Building 7,Longcheng Industrial
Park,No.440,Longguan Road,
Dalang Street, Longhua, Shenzhen,
Guangdong, China
TEL: [phone]
FAX: [phone]
www.everfocus.com.cn
mark[email protected]
EverFocus China - Beijing:
Room 609, Technology Trade Building,
Shangdi Information Industry Base,
Haidian District, Beijing 100085, China
TEL: [phone]~39
FAX: [phone]
www.everfocus.com.cn
[e-mail]
EverFocus Japan:
3F, Kuramochi, Building II
2-2-3 Koto-Bashi, Sumida-Ku,
Tokyo, 130-0022, Japan
TEL: [phone]
FAX: [phone]
www.everfocus.co.jp
[e-mail]
EverFocus USA - California:
1801 Highland Avenue, Unit A, Duarte, CA
91010, USA
TEL: [phone]
FAX: [phone]
www.everfocus.com
[e-mail]
Your EverFocus product is designed
and manufactured with high quality
materials and components which can
be recycled and reused.
This symbol means that electrical and
electronic equipment, at their
end-of-life, should be disposed of
separately from your household waste.
Please, dispose of this equipment at
your local community waste
collection/recycling centre.
In the European Union there are
separate collection systems for used
electrical and electronic product.
Please, help us to conserve the
environment we live in!
Ihr EverFocus Produkt wurde entwickelt
und hergestellt mit qualitativ
hochwertigen Materialien und
Komponenten, die recycelt und wieder
verwendet werden können.
Dieses Symbol bedeutet, dass
elektrische und elektronische Geräte am
Ende ihrer Nutzungsdauer vom
Hausmüll getrennt entsorgt werden
sollen.
Bitte entsorgen Sie dieses Gerät bei
Ihrer örtlichen kommunalen
Sammelstelle oder im Recycling Centre.
Helfen Sie uns bitte, die Umwelt zu
erhalten, in der wir leben!
P/N: 4605D099002001D