EverFocus EDN228 User manual

EDN228 Mini Dome Network Camera
2-Megapixel & WDR
User’s Manual
Copyright © EverFocus Electronics Corp,
Release Date: November, 2014

Copyright 1995 - 2014 EverFocus Electronics Corp.
All rights reserved. No part of the contents of this manual may be reproduced or transmitted in any form or by
any means without written permission of the EverFocus Electronics Corporation.
EverFocus
12F-1, No.79, Sec. 1, Shin-Tai Wu Road,
Hsi-Chih, New Taipei City, Taiwan
TEL: [phone]
FAX: [phone]
www.everfocus.com.tw
November, 2014

i
About this document
All the safety and operating instructions should be read and followed before the unit is operated. This
manual should be retained for future reference. The information in this manual was current when
published. The manufacturer reserves the right to revise and improve its products. All specifications are
therefore subject to change without notice.
Regulatory Notices
FCC Notice "Declaration of Conformity Information"
This equipment has been tested and found to comply with the limits for a Class
A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful interference
to radio or television reception, which can be determined by turning the equipment off and on, the user
is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
- Consult the dealer or an experienced radio/TV technician for help.
Warning: Changes or modifications made to this equipment, not expressly approved by EverFocus or
parties authorized by EverFocus could void the user's authority to operate the equipment.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause undesired
operation.
EverFocus Electronics Corp.
12F-1, No. 79, Sec. 1, Shin-Tai Wu Rd.,
Hsi-Chi, New Taipei City, Taiwan, R.O.C.
EDN228 camera complies with CE and FCC.

ii
Precautions
1. Do not install the camera near electric or magnetic fields.
Install the camera away from TV/radio transmitters, magnets, electric motors, transformers and
audio speakers since the electromagnetic fields generated from these devices may distort the video
image or otherwise interfere with camera operation.
2. Never disassemble the camera beyond the recommendations in this manual nor introduce
materials other than those recommended herein.
Improper disassembly or introduction of corrosive materials may result in equipment failure or other
damage.
3. Try to avoid facing the camera toward the sun.
In some circumstances, direct sunlight may cause permanent damage to the sensor and/or internal
circuits, as well as creating unbalanced illumination beyond the capability of the camera to
compensate.
4. Keep the power cord away from water and other liquids and never touch the power cord with wet
hands.
Touching a wet power cord with your hands or touching the power cord with wet hands may result in
electric shock.
5. Never install the camera in areas exposed to oil, gas or solvents.
Oil, gas or solvents may result in equipment failure, electric shock or, in extreme cases, fire.
6. Cleaning
For cameras with interchangeable lenses, do not touch the surface of the sensor directly with the
hands. Use lens tissue or a cotton tipped applicator and ethanol to clean the sensor and the camera
lens. Use a damp soft cloth to remove any dirt from the camera body. Please do not use complex
solvents, corrosive or abrasive agents for cleaning of any part of the camera.
7. Do not operate the camera beyond the specified temperature, humidity or power source ratings.
Use the camera at temperatures within -10°C ~ 50°C / -14°F~122°F, and humidity between 20% and
80%; this device is not rated as submersible. The input power source is 12 VDC / PoE. Be sure to
connect the proper + / - polarity and voltage, as incorrect polarity or too high a voltage will likely
cause the camera to fail, and such damage is not covered by the warranty. The use of properly fused
or Class 3 power limited type supplies is highly recommended.
8. Mounting
Use care in selecting a solid mounting surface which will support the weight of the camera plus any
wind, snow, ice or other loading, and securely attach the camera to the mounting surface using
screws and anchors which will properly support the camera. If necessary (e.g. when mounting to
drop ceilings) use a safety wire to provide additional support for the camera.

iii
CONTENTS
1. Introduction.................................................................................................................................. 1
2. Physical Description .................................................................................................................... 2
2.1 Dimensions ..........................................................................................................................................3
3. Features......................................................................................................................................... 3
4. Installation.................................................................................................................................... 4
4.1 Packing List...........................................................................................................................................4
4.2 Basic Installation ..................................................................................................................................4
5. Accessing the User Interface ...................................................................................................... 7
5.1 Checking the Dynamic IP Address........................................................................................................7
5.2 Settings for Microsoft Internet Explorer..............................................................................................9
5.3 Connecting the Camera to the Network............................................................................................11
5.4 Live View Window..............................................................................................................................13
6. Playback ...................................................................................................................................... 16
6.1 Remote Playback Using Playback Page..............................................................................................16
6.2 Setting Up the Playback Function......................................................................................................19
6.2.1 Inserting / Removing the micro SD Card..............................................................................19
6.2.2 Testing the Playback Function..................................................................................................20
6.3 Playing Back Using ARV Viewer .........................................................................................................22
7. Settings........................................................................................................................................ 24
7.1 System Settings..................................................................................................................................25
7.1.1 Network ...............................................................................................................................25
7.1.2 Date / Time ..........................................................................................................................32
7.1.3 Storage .................................................................................................................................33
7.1.4 Display and Overlay..............................................................................................................35
7.1.5 System Maintenance............................................................................................................37
7.1.6 System Information..............................................................................................................40
7.1.7 User ......................................................................................................................................41
7.1.8 Black /White List ..................................................................................................................43
7.2 Camera Settings .................................................................................................................................44
7.2.1 Streaming.............................................................................................................................44
7.2.2 Profile...................................................................................................................................47
7.2.3 Camera .................................................................................................................................49
7.2.4 Schedule...............................................................................................................................52
7.2.5 Image....................................................................................................................................53
7.3 Event Settings ....................................................................................................................................55
7.3.1 Event Wizard ........................................................................................................................55
7.3.2 Event ....................................................................................................................................56

iv
7.3.3 Notification ..........................................................................................................................60
7.4 Link to Smart Phone App ...................................................................................................................63
8. Upgrading Firmware Using IP Utility....................................................................................... 64
9. Specifications ............................................................................................................................. 66
10. Troubleshooting ......................................................................................................................... 68
Appendix............................................................................................................................................ 71
A. Tested Card Brands ............................................................................................................................71
B. Enabling the Multicast Function........................................................................................................72

EDN228
1
1. Introduction
The EDN228 is a 2-megapixel mini dome IP camera, providing 30 fps at 1920 x 1080 viewing resolution. The
camera supports dual streams from H.264 & MJPEG video compression formats. The camera has a built-in
micro SDHC card slot, providing local recording when the event was triggered. Power over Ethernet (IEEE
802.3af) supplies power to the camera via the network for easy installation with only one cable,
eliminating the need for power cables and reducing installation costs. EDN228 conforms to ONVIF / PSIA
for compatibility with other network video devices – even from other manufacturers. You can also use
EverFocus Mobile Applications to remotely view the live views of the cameras through your handheld
devices; or use EverFocus CMS to remotely manage multiple IP devices connected on the network.
System Requirement
Before installing, please check that your computer meets these system requirements.
Operating System: Microsoft Windows XP / Vista (32-bit) / 7 (32-bit)
Microsoft Internet Explorer 7 or above
Note: For using the Internet Explorer, some settings are required. Please refer to 5.2 Settings for
Microsoft Internet Explorer.

 EDN228
2
2. PhysicalDescription
NO.ItemNameDescriptions
1FixScrews Usedtoadjustlens.
2LensFixedlens.
312VDCableUsedtoconnecttoa12VDCpowersupply.
4RJ‐45ConnectorCableUsedtoconnecttoaLAN/PoEcable.
5MicroSDHC/SDXCCardSlotInsertamicroSDHC/SDXCcardhere.
6ResetButtonPressthebuttontoresetthecamera.

CableConnection
CableNameDescription
PowerCableConnectstothe12VDCpowersource.Youcanoptionallyusethesupplied
PowerAdapterPigtailorapoweradapter.
PowerAdapterPigtailConnectsoneendtothePowerCable,andtheotherendtothe12VDC
powersource(blackwiretogroundend;redtopositiveend).

EDN228
3
2
2.1 Dimensions
3. Features
•1/2.8” HD color CMOS image sensor delivers high resolution, and supports both H.264, MPEG-4
and M-JPEG in full frame rate
•Wide dynamic range
•Provides true day / night functionality with automatic IR filter operation
•Multi profiles settings for allows choice of image quality to fit the environment
•High performance noise filter improves image quality
•IDual power capability PoE or 12 VDC for flexible installation
•Supports live monitoring of video from mobile devices via MobileFocus / MobileFocus Plus apps
(iOS and Android)
•ONVIF / PSIA compliant

EDN228
4
4. Installation
4.1 Packing List
Please check that there is no missing item in the package before installing.
•
Camera x 1
•
Hexagon Wrench x 1
•
Screw with Washer x 3
•
Power Adapter Pigtail x 1
•Screw Anchor x 3
•Cable Gland and Screw Cap x 1
(with one conduit on the inner stopper)
•Software CD x 1
•Sticker x 1
•Quick Installation Guide x 1
•Waterproof Ring x 1
Note:
1. Equipment configurations and supplied accessories vary by country. Please consult your local
EverFocus office or agents for more information. Please also keep the shipping carton for possible
future use.
2. Contact the shipper if any items appear to have been damaged in the shipping process.
4.2 Basic Installation
1. Before screwing the camera to the wall, stick the Sticker on the wall / ceiling to mark the position
for installation. Drill three holes on the wall / ceiling according to the supplied Sticker and push the
supplied three Anchors into the three holes on the wall / ceiling.
2. Unscrew the camera cover and screw the camera base to the ceiling / wall by using the supplied
three Screws with Washers.

EDN228
5
3. Loosen two Set Screws to adjust the lens.
4. Optionally insert the micro SDHC / SDXC card.
5. Connect the LAN / PoE cable to the camera.
a. Remove the Screw Cap from the Cable Gland.
b. Insert a RJ-45 network cable (without the RJ-45 connector on the one end) through the Cable
Gland and Screw Cap.

EDN228
6
c. Place the Waterproof Ring into the LAN / PoE cable. Connect the RJ-45 cable to the RJ-45
Connector Cable. Tightly screw the Cable Gland and Screw Cap to the RJ-45 Connector Cable.
6. Optionally connect the camera to the 12 VDC power source using the supplied Power Adapter
Pigtail or a power adapter.
7. Screw back the camera cover to the camera base.

EDN228
7
5. Accessing the User Interface
This section explains how to access the Web interface of the camera for configuration.
5.1 Checking the Dynamic IP Address
You can look up the IP address and access the Web interface of the camera using the IP Utility (IPU)
software included in the software CD or from the Website of EverFocus (click hereto download).
Please connect the IP camera in the same LAN of your computer.
1. Save IP Utility Setup AutoRun.exe in your computer. Double click the .exe file and follow
the on-screen instructions. Check Run IPUtility.exe and click the Finish button, the IP Utility will
be launched to search the IP devices connected in the same LAN automatically.
2. To access to the Live View window, double click the IP address of the desired device, the login
window pops up. Type the user ID and password to log in. By default, the user ID is user1 and the
password is 11111111.

EDN228
8
3. Click OK, the Live View window appears.
Note:
1. You might be required to download ActiveX for viewing the camera feed. If asked, click Yes.
2. To enable Remote Live View, Firmware Upgrade and ActiveX Prompt on Internet Explorer,
some settings have to be complete. Please refer to 5.2 Settings for Microsoft Internet
Explorer in the User’s Manual.
4. To optionally configure the Machine Name, IP Address, IP Type or Port Number using the IPU:
a. Log in the camera by checking the desired model and then click the Log in icon. The
Log in dialog box appears.
b. Type the Username and Password. Click the OK button, the Login status displays.
Note:
1. The default user ID is user1 and the default password is 11111111.
2. If you select more than one camera that has the same user ID / password, you will be
able to log in several cameras at once.
c. Right click the column to configure the settings. Click the Apply Changes button to
apply and save the settings.
Note:
1. Most networks uses DHCP to assign IP address, if you are unsure of your network
settings, please consult your network administrators for configuration details.
2. If you want to set up PPPoE, please refer to 6.1.1 Network.

EDN228
9
5.2 Settings for Microsoft Internet Explorer
To enable Remote Live View, Firmware Upgrade and ActiveX Prompt on Internet Explorer, some
settings have to be complete. Please follow the steps below:
1. On the computer, click Start > Control Panel > System and Security > Action Center (click Change
User Account Control Settings), the User Account Control Settings window appears. Adjust the
slide bar to Never Notify and then click OK. Restart your computer if requested.
2. Open the Internet Explore, click Tools > Internet Options > Security Tab > Custom Level, the
Security Settings windows appears.

EDN228
10
3. In the Download unsigned ActiveX controls field, select Prompt. In the Include local directory
path when uploading files to a server field, select Enable. Click OK.
4. In the Internet Options window, click the Advanced tab and then disable Enable memory
protection to help mitigate online attacks. Click OK.

EDN228
11
5.3 Connecting the Camera to the Network
There are three methods to connect the IP camera to the network: Router or LAN Connection, Direct
High-Speed Connection and One-to-One Connection.
Router or LAN connection
This is the most common connection in which the IP camera is connected to a router and allows
multiple users on and off site to see the IP camera on a LAN/WAN (Internet). The camera must be
assigned an IP address that is compatible with its LAN. By setting up port forwarding on the router, you
can remotely access the cameras from outside of the LAN via the Internet. To remotely access the Web
interface of the IP camera, please refer to 6.1.1 DDNS. To set up port forwarding, please consult the
manual of the router.

EDN228
12
Direct High-Speed Connection
In a Direct High-Speed Connection, the camera connects directly to a modem without the need for a
router. You need to set the static or dynamic WAN IP address assigned by your ISP (Internet Service
Provider) in the camera’s configuration web pages. To access the camera, just type
“http://xxx.xxx.xxx.xxx”, where xxx.xxx.xxx.xxx is the IP address given by your ISP. If you have a dynamic
IP address, this connection may require that you use DDNS for a reliable connection. Please refer to
6.1.1 DDNS.
One-to-One Connection (Directly from PC to IP Camera)
You can connect directly without using a switch, router or modem. However, only the PC connected to
the camera will be able to view the IP camera. You will also have to manually assign a compatible IP
address to both the computer and the IP camera. Unless the PC has another network connection, the IP
camera will be the only network device visible to the PC. See the diagram below:

EDN228
13
5.4 Live View Window
1. Live View
Click the Live View button to display the Live View window. If you experience video feed lag time (if
connected via Internet), you can reduce the resolution or limit the number of streams. See 6.2.1
Streaming.
2. Playback
Click the Playback button to play back the recorded data directly from the on-camera micro SD /
SDHC card. For this function to become active, you have to insert a micro SD / SDHC card into the
micro SD / SDHC card slot on the camera (see 6.2 Setting up the Playback Function). For the tested
card brands, please refer to Appendix A.
3. Snapshot
Click the Snapshot button to take a snapshot. By default, the snapshot will be saved at
C:\EverFocus\. To change the location, see Record to Local in 7.1.3 Storage.
Note: For Microsoft IE10 and above users, some settings have to be complete to enable this
function (see B. Snapshot/Record error message in 10. Troubleshooting).
4. Record
Click the Record button to start / stop recording the current video stream. By default, this icon is
only for one-minute video recording and the recordings will be saved at C:\EverFocus\. To change

EDN228
14
the recording time, see File Size in 7.1.3 Storage. To change the location, see Record to Local in 7.1.3
Storage. To record long-period recordings, please set up a recording schedule (7.3.2 Schedule
Settings). To change the source video stream and recording format, see Recording and Snapshot
Settings in 7.1.3 Storage.
5. Setting
Click the Setting button to enter the Settings page (see 7. Settings).
6. Wizard
Click the Wizard button to enter the Setup Wizard.
7. Hallway Display (9:16): Click the Rotate button to rotate the live image. This function
allows users to monitor vertically-oriented areas such as hallway, corridors and aisles.
Note: To achieve the best 9:16 display effect, it’s recommended to:
1. Install the camera sideways by rotating the camera to the left or right by 90°.
2. Select a 16:9 View Size (e.g. 1920x1080 / 1024x768).
3. Use the Rotate button.