EverFocus EQ150 User manual

1 1/ /3 3” ” H Hi ig gh h R Re es so ol lu ut ti io on n B B/ /W W D Di ig gi it ta al l C Ca am me
er ra a
E
Q15
0
User’s Manual
and
Operation Instructions

Notice
This manual is presented to the users of EQ150 by EverFocus Electronics
Corp. With years of engineering researches, EverFocus has spared no effort
to provide the high quality products to the worldwide users. For the policy
of continual product improvement, EverFocus reserves the right to make
changes to the product specifications and documentation without notice.
All the components of the products, including accessories, components, and
outlook, are based on the agreements of each deals to satisfy all kinds of
users. Meanwhile, please be advised that every step of operation must
follow the instruction of this manual to keep EQ150 working under the best
condition. Please notice that EverFocus will not be charged any claims or
renewing cases resulted from inappropriate operation.

Table of Contents
Safety Warning …………………………………………1
Introduction……………………………………………..2
Specification…………………………………………….3
Major Parts and Their Functions………………….…..4
Installation Instructions………………………….….…8

1. Handle the camera with care.
Be careful when handling the camera, do not drop it or subject
it to strong shock or vibration to prevent any damages to it. Do
not disassemble it or place it on an unstable base.
2. Do not install the camera near electric or magnetic fields.
Installed the camera away from TV, radio transmitter, magnet,
electric motor, transformer, audio speakers because the
magnetic fields generate from above devices will distort the
video image.
3. Do not install the camera in the high temperature environment.
Installed the camera away from stoves, or other heat
generating devices as the high temperature could cause
deformation, discoloration or other damages of the camera.
Install the camera at where the temperature range will stay
between 0℃to 50℃ (32℉ to 122℉).
4. Never face the camera toward the sun.
Never aim the camera at the sun or other extremely bright objects
whether it is in use or not.
5. Cleaning
Do not touch the surface of CCD sensor by hand directly. Use
a soft cloth to remove the dirt from the camera body. Use lens
tissue or a cotton tipped applicator and ethanol to clean the
CCD sensor and the camera lens. When the camera is not in
use, put the cover cap on the lens mount.
Safet
y
Warnin
g
1

The new EQ150 series is a solid-state color video camera specially
designed for high quality surveillance applications. It incorporates
break through DSP technology that provides most reliable and
accurate color picture in security industry. The camera is
convenient to use with C-mount or CS-mount lenses and easy
back-focus adjustment help to achieve installation efficiency.
Main Features :
¾1/3” B/W CCD pick up device for more than 560 TV lines of horizontal
resolution
¾Sophisticated DSP (Digital Signal Processing) circuitry design that delivers
excellent picture quality and performance.
¾Wide range automatic electronic shutter: 1/50(1/60)~1/100,000
¾Auto line lock with external phase adjustment
¾Used with either C-mount or CS-mount lenses and easy back-focus a
Adjustment.
¾System available in EIA or CCIR.
Introduction
2

Pickup Device 1/3" SONY B/W CCD
Picture Elements 768 x 494 (EIA)
752 x 582 (CCIR)
Horizontal Resolution 560 TV lines
Sensitivity 0.01 lux/F=1.2
S/N Ratio Over 48 dB
Electronic Shutter 1/50(1/60)~1/100,000 sec
Auto Iris Video / Direct Drive switch
Flickerless On/Off
Back Light Comp. On/Off
Electronic Shutter On/Off
Auto Gain Control On/Off
Line Lock On/Off
Audio Optional
Gamma Correction 0.45
Power Source 2 types: 12VDC/24VAC;90~260VAC
Power consumption 5W max.
Dimensions 50mm(H) x 57mm (W) x 140.2mm(D);
1.97" (H) x 2.24"(W) x 5.52" (D)
Operature Temparature 0°C~50°C ; 32°F~122°F (20%~80% Humidity)
Certifications FCC/CE
S
p
ecification
3

Front
Side
Side
Top
Rear
(EQ150) Rear(EQ150A)
Major Parts Names and Their Functions
4
1
2
3
4
5
6
7
8
9
10
9
11

1. Focal Length Adjustment Ring
Use this ring to adjust the appropriate focal length according to the type
of lens. Rotate the ring clockwise for the CS-mount lens, rotate it
counterclockwise for the C-mount lens. The factory setting is C-mount.
2. Lens Mount
To mount an appropriate C-mount or CS-mount lens.
3. Locking Screw
Use the locking screw to fix the focal length.
4. Lens Connector (4 pin socket)
To connect to the lens plug of the auto iris lens.
5. Control Switches
There are 6 control switches located on the sideboard, which are for the
setting of the special features. The switches in orders are for Flickerless,
Back Light Compensation, Electronic Shutter, Automatic Gain Control,
Line-Lock and Auto Iris Lens type.
FL (Flickerless Function) On/Normal
When picture flicker fiercely, turn FL on, then the camera will stabilize
the speed of electronic shutter at 1/100(EIA) or 1/120(CCIR)
automatically, and reduce the flicker immediately. The default setting is
Normal.
BLC (Back Light Compensation) On/Normal
When BLC is turned on, the AGC, ES and IRIS operating point is
determined by averaging over the center area instead of entire
field-of-view, so that a dimly-lit foreground object at center area can be
clearly distinguished from brightly-lit backgrounds.
BLC should not be used unless it is needed to compensate for back-lit.
The default setting is Normal.
5

ES (Electronic Shutter) Off/On
ES ON: The camera continuously adjusts the shutter speed from 1/60
(EIA), 1/50(CCIR) second to 1/100,000 second according to the
luminance conditions of the scene.
ES OFF: The shutter speed is fixed at 1/60 (EIA), 1/50 (CCIR) second.
Set ES OFF, when auto iris lens is used or flicker is observed under a
very bright fluorescent lamp. Otherwise, turn ES on for optimum
performance. The default setting is ON.
AGC (Automatic Gain Control) Off/On
AGC ON: The sensitivity increases automatically when light is low.
AGC OFF: A-low-noise picture is obtained under a low light
condition.
The default setting is ON.
LL (Line-Lock) Off/On
To select the sync mode between Internal Sync.(LL off) and
Line-Lock (LL on).
Set the line-lock off, the camera will synchronize to the internal time
base. Set the line-lock on, the camera’s vertical synchronization can
be driven by the AC signal in the power lines.
Note: Line-Lock sync mode operation is possible only when used
with an AC power source; it’s not possible with a DC power source.
6