EverFocus EPD200A User manual

EVERFOCUS
Indoor Pendent Dome Camera
Operation Instructions
Model No. EPD200
Please read this manual first for correct installation and operation. This manual should be retained
for future reference. The information in this manual was current when published. The
manufacturer reserves the right to revise and improve its products. All specifications are therefore
subject to change without notice.
PRECAUTIONS
1. Do not install the camera near electric or magnetic fields.
Install the camera away from TV, radio transmitter, magnet, electric motor, transformer,
audio speakers since the magnetic fields generate from above devices will distort the video
images.
2. Never disassemble the camera nor put impurities in it.
Disassembly or impurities may result in trouble or fire.
3. Never face the camera toward the sun.
Direct sunlight or severe ray may cause fatal damage to sensor and internal circuit.
4. Keep the power cord away from water and liquid.
Touching the wet power cord may result in electric shock.
5. Never install the camera in areas exposed to water, oil or gas.
Water, oil or gas may result in failure, electric shock or fire.

1
6. Cleaning
Do not touch the surface of sensor by hand directly. Use a soft cloth to remove the dirt from
the camera body. Use lens tissue or a cotton swab and ethanol to clean the sensor and the
camera lens.
7. Do not operate the camera beyond the specified temperature, humidity or
power source ratings.
Use the camera at temperatures within 0℃~ 50℃/32℉~122℉and humidity between 20%~
80%. The input power source is 12VDC/24VAC.
PREFACE
EPD200 is compact, full functioned CCD Color Cameras for indoor pendent mount. The
dome camera is designed with advanced digital processing circuitry for high resolution 1/3"
CCD sensor, it has DIP switch for FL ON/OFF, BLC ON/OFF, AGC ON/OFF. The dome
camera uses a vari-focal auto iris lens for discreet surveillance or close-up viewing and it
features with iris level volume control for the best viewing quality.
FEATURES
z1/3” SONY CCD pick up device for more than 380 TV lines of horizontal resolution
zThe high sensitivity of 1.0 Lux/F=1.2 is achieved by using 1/3” SONY CCD
zThe Electronic Shutter and AGC functions allow the camera to be used in environment
with varying light levels
zBuilt-in Vari-Focal lens(optional)
zWith manual PAN mechanism up to 90 degree
zFL, BLC, AGC On/Off switchable
zCompact size
zSystem available for NTSC or PAL
CONTENT LIST
1. Camera Unit
2. Operation Instructions (this document)
3. Hex Wrench
4. Power Extension Cable
5. Video Cable for testing Video Connector
OPTIONALACCESSORY
•EN220 5.6-inch LCD Test Monitor

2
SPECIFICATION
Pickup Device 1/3" SONY Super HAD CCD
Video Format
N
TSC or PAL
Scanning System
N
TSC: 525 TV lines, 60 fields/sec.
PAL: 625 TV lines, 50 fields/sec.
Picture Elements 510 x 492 (NTSC); 500 x 582 (PAL)
Horizontal Resolution 380 TVL
Sensitivity 0.3 Lux /F=1.2
S/N Ratio Over 48dB(AGC Off)
Electronic Shutter 1/50(1/60)~1/100,000
Lens Vari-Focal or Fixed Lens
Video Output BNC 1.0Vp-p 75ohm
Back Light Comp.. On/Off switch
Auto Gain Control On/Off switch
Flickerless On/Off switch
Auto White Balance Auto
Auto IRIS DC-Drive
Gamma Correction 0.45
Sync. Mode Internal Sync.
Power Source Two types:
12VDC/24VAC
12VDC only
Power Consumption 12VDC:3W max.
24VAC: 1.5W max
Video Output Connector BNC output x 1
2.5mm Lock x 1
AC 24V Power Connector + Video 2.5mm x 2-pin(for DC jack)
2.0mm x 2-pin(for BNC)
DC 12V Power Connector + Video 1.25mm x 4-pin, (1BNC, DC jack)
Weight 0.3 kg ; 0.66 lbs
Dimension 110mm(W)x 125(H)/ 4.33”(W) x4.92”(H)
Pendent Tube Diameter: 26mm/1.06”
Operating Temperature 0~50 ; 32°F~122°F (20%~80% Humidity)
Certifications CE, FCC

3
DIMENSION DIAGRAM
a. Conduit Size
b.
26mm/1.06”
125mm/4.92”
110mm/4.33”
90mm/3.54”
80mm/3.15””

4
HARDWARE OVERVIEW
a. Front panel design (For Vari-Focal Lens Model)
b. Front panel design (For Fixed Lens Model)
IRIS LEVEL
CONTROL
BNC Pigtail Slot for
Focusing and
Testing Module
BLC – Back Light
Compensation
AGC (Automatic
Gain Control)
FL(Flickerless)
BNC Pigtail Slot for
Focusing and
Testing Module
BLC – Back Light
Compensation
AGC (Automatic
Gain Control)
ES(Electronic
Shutter)
FL(Flickerless)

5
INSTALLATION
This section covers simple steps and detail installation. Please follow instruction for preventing
any unnecessary damage.
Simple Steps:
1. Connect to 26mm/1.06” EMT Conduit Pipe and lock it with Hex Wrench
2. Open camera bubble cover
3. Connect to testing monitor(optional accessories)
4. Adjust lens, camera position
5. Optional adjust camera setting on Dip Switch
1. Mount Camera
a. Pre-install 26mm/1.06” EMT conduit pipe and wire video and power cables though conduit
pipe. Connect power and video to the camera.
b. Locking pipe with camera by tightening set screws with supplied Hex wrench.
Note!! When connect to 12VDC with Power Extension cable . Please make sure you
connect powr +,- correctly. Wrong connection may damage the camera.
Camera
26mm EMT
Conduit Pipe
2.5mm Hex
Wrench
Set Screws

6
2. Open Camera Bubble Cover
Turn the camera bubble until you see the arrow face to here.
3. Connecting to testing monitor EN220
Connect the BNC Pigtail accessory to the front of the module for help with focusing or video
testing.
White (+)
Black (-)

7
4. Adjust Camera Position and Lens
a.Adjust camera position (Tilt angle up to 90 degree): Adjust camera to the position you
like. The turning angel is up to 90 degree. Use ‘tool-less’ screws on the side of the module
to secure position.
b. Zoom and focus adjustments (For Vari-focal Lens Model)
After the camera was installed, the zoom and focus of the lens must be adjusted.
(1) Loosen the zoom ring knob, and then turn the ring towards <W> or <T> as necessary to
obtain the desired view range.
W side (Zoom out)
The viewing range will be wider and the subject is smaller.
T side (Zoom in)
The viewing range will be smaller and the subject is larger.
(2) Loosen the focus ring knob, then turn the ring towards <∞> or <N> as necessary to
obtain the clear video image.
(3) Repeat steps 1 and 2 until the best image is obtained.
Once the lens setting finished, tighten the zoom ring and the focus ring knobs.
CAMERA SETTING
¾BLC (Back Light Compensation)
When BLC is turned on, the AGC, FL and IRIS operating point is determined by averaging over
the center area instead of entire field-of-view, so that a dimly-lit foreground object at center area
can be clearly distinguished from brightly-lit backgrounds. BLC should not be used unless it is
needed to compensate for back-light.
The default setting is OFF. For Auto-Iris lens model, the brightness can also be adjusted via the
Iris level control VR.
¾AGC (Automatic Gain Control)
AGC ON: The sensitivity increases automatically when light is low.
AGC OFF: A-low-noise picture is obtained under a low light condition.
90 Degree
Tool-less Screws

8
The default setting is ON.
¾FL (Flickerless)
When picture flicker fiercely, turn FL on, then the camera will stabilize the speed of electronic
shutter at 1/100(S)(NTSC) or 1/120(S)(PAL) automatically, and reduce the flicker immediately.
The default setting is OFF.
¾IRIS Level Control (For Vari-Focal Lens Model)
Brightness Level can be adjusted from the IRIS level VR while using the direct drive lens.
•Turn counterclockwise to L to get darker picture.
•Turn clockwise to H to get brighter picture.¾Electronic Shutter (For Fixed Lens Model)
ES ON: The camera continuously adjusts the shutter speed from 1/60 (NTSC), 1/50 (PAL) second
to 1/100,000 second according to the luminance conditions of the scene.
ES OFF: The shutter speed is fixed at 1/60 (NTSC),1/50 (PAL) second.
Set ES OFF, when auto iris lens is used or flicker is observed under a very bright fluorescent lamp.
Otherwise, turn ES on for optimum performance.

9
EverFocus Electronics Corp.
Head Office:
12F, No.79 Sec. 1 Shin-Tai Wu Road,
Hsi-Chih, Taipei, Taiwan
TEL: [phone]
FAX: [phone]
www.everfocus.com.tw
USA L.A. Office:
1801 Highland Ave. Unit A
Duarte, CA 91010, U.S.A.
TEL: [phone]
FAX: [phone]
www.everfocus.com
USA N.Y. Office:
415 Oser Avenue Unit S
Hauppauge, NY 11788
TEL: [phone]
FAX: [phone]
www.everfocus.com
Europe Office:
Albert-Einstein-Strasse 1
D-46446 Emmerich, Germany
TEL: [phone]
www.everfocus.de
China Office:
Room B-05D-1, KESHI PLAZA , Shangdi
Information Industry Base,
Haidian District, Beijing China 100085
TEL: [phone]/38/39
FAX: [phone]
www.everfocus.com.cn
Japan Office:
1809 WBG MARIBU East 18F,
2-6 Nakase.Mihama-ku.
Chiba city 261-7118, Japan
TEL: [phone]
FAX: [phone]
www.everfocus.com
Y
our EverFocus product is desi
g
ned and
manufactured with high quality materials and
components which can be recycled and
reused.
This symbol means that electrical and
electronic equipment, at their end-of-life,
should be disposed of separately from your
household waste.
Please, dispose of this equipment at your
local community waste collection/recycling
centre.
In the European Union there are separate
collection systems for used electrical and
electronic product.
Please, help us to conserve the environment
we live in!
Ihr EverFocus Produkt wurde entwickelt und
hergestellt mit qualitativ hochwertigen
Materialien und Komponenten, die recycelt
und wieder verwendet werden können.
Dieses Symbol bedeutet, dass elektrische und
elektronische Geräte am Ende ihrer
Nutzungsdauer vom Hausmüll getrennt
entsorgt werden sollen.
Bitte entsorgen Sie dieses Gerät bei Ihrer
örtlichen kommunalen Sammelstelle oder im
Recycling Centre.
Helfen Sie uns bitte, die Umwelt zu erhalten, in
der wir leben!
P/N: MEFDG00400