EverFocus EPN Series User manual

EPN Series IP Speed Dome
EPN4220d/4220di
User’s Manual
Copyright © EverFocus Electronics Corp.
Release Date: January, 2016

Copyright 1995-2016 EverFocus Electronics Corp.
All rights reserved. No part of the contents of this manual may be reproduced or transmitted in any form
or by any means without written permission of the EverFocus Electronics Corporation.
EverFocus
12F, No.79, Sec. 1, Shin-Tai Wu Road,
Hsi-Chih, New Taipei City, Taiwan
TEL: [phone]
FAX: [phone]
www.everfocus.com.tw
January, 2016

i
About this document
All the safety and operating instructions should be read and followed before the unit is operated. This
manual should be retained for future reference. The information in this manual was current when
published. The manufacturer reserves the right to revise and improve its products. All specifications are
therefore subject to change without notice.
Regulatory Notices
FCC Notice "Declaration of Conformity Information"
This equipment has been tested and found to comply with the limits for a Class
A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Warning: Changes or modifications made to this equipment, not expressly approved by EverFocus or
parties authorized by EverFocus could void the user's authority to operate the equipment.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause undesired
operation.
EverFocus Electronics Corp.
12F-1, No.79, Sec. 1, Shin-Tai Wu Road,
Hsi-Chih, New Taipei City, Taiwan
EPN Series cameras comply with CE and FCC.

ii
Precautions
1. Do not install the camera near electric or magnetic fields.
Install the camera away from TV/radio transmitters, magnets, electric motors, transformers and
audio speakers since the electromagnetic fields generated from these devices may distort the video
image or otherwise interfere with camera operation.
2. Never disassemble the camera beyond the recommendations in this manual nor introduce
materials other than those recommended herein.
Improper disassembly or introduction of corrosive materials may result in equipment failure or other
damage.
3. Try to avoid facing the camera toward the sun.
In some circumstances, direct sunlight may cause permanent damage to the sensor and/or internal
circuits, as well as creating unbalanced illumination beyond the capability of the camera to
compensate.
4. Keep the power cord away from water and other liquids and never touch the power cord with wet
hands.
Touching a wet power cord with your hands or touching the power cord with wet hands may result
in electric shock.
5. Never install the camera in areas exposed to oil, gas or solvents.
Oil, gas or solvents may result in equipment failure, electric shock or, in extreme cases, fire.
6. Cleaning
For cameras with interchangeable lenses, do not touch the surface of the sensor directly with the
hands. Use lens tissue or a cotton tipped applicator and ethanol to clean the sensor and the camera
lens. Use a damp soft cloth to remove any dirt from the camera body. Please do not use complex
solvents, corrosive or abrasive agents for cleaning of any part of the camera.
7. Do not operate the camera beyond the specified temperature, humidity or power source ratings.
Use the outdoor camera at temperatures within -40°C ~ +50°C ≦95% / -40°F ~ +122°F ≦95% and
the indoor camera at temperatures within -10°C ~ +50°C ≦85% / 14°F ~ +122°F ≦85%; this
device is not rated as submersible. The input power source is 24 VAC~ / PoE. Be sure to connect the
proper + / - polarity and voltage, as incorrect polarity or too high a voltage will likely cause the
camera to fail, and such damage is not covered by the warranty. The use of properly fused or Class 2
power limited type supplies is highly recommended.
8. Mounting
Use care in selecting a solid mounting surface which will support the weight of the camera plus any
wind, snow, ice or other loading, and securely attach the camera to the mounting surface using
screws and anchors which will properly support the camera. If necessary (e.g. when mounting to
drop ceilings) use a safety wire to provide additional support for the camera.

iii
Contents
1. Introduction.....................................................................................................................................1
2. Features ............................................................................................................................................2
3. Installation.......................................................................................................................................4
3.1 Packing List ...............................................................................................................................4
3.2 Optional Accessories ................................................................................................................5
3.3 Cable Descriptions....................................................................................................................6
3.4 I/O Terminal Block....................................................................................................................7
3.5 Basic Installation for Outdoor Models .....................................................................................8
3.5.1 Installation Requirements .........................................................................................8
3.5.2 Important Note for Installation .................................................................................9
3.5.2.1 Replacing the Desiccant Bags .....................................................................9
3.5.2.2 Inserting a Micro SD Card .........................................................................10
3.5.2.3 Restoring to Factory Default.....................................................................10
3.5.2.4 Optionally Setting Up the DIP Switch .......................................................11
3.5.3 Wall-Mount Installation...........................................................................................15
3.5.4 Ceiling Mount Installation .......................................................................................18
4. Accessing the User Interface ...................................................................................................22
4.1 Checking the Dynamic IP Address..........................................................................................22
4.2 Settings for Microsoft Internet Explorer................................................................................25
4.3 Connecting the Camera to the Network................................................................................27
5. Live View Window........................................................................................................................29
5.1 PTZ Control Window ..............................................................................................................33
6. Playback ..........................................................................................................................................35
6.1 Remote Playback Using Playback Page ..................................................................................35
6.2 Setting Up the Playback Function ..........................................................................................37
6.2.1 Preparing the Micro SD Card ...................................................................................37
6.2.2 Testing the Playback Function .................................................................................38
6.3 Playing Back Using ARV Viewer..............................................................................................39
7. Settings ...........................................................................................................................................40
7.1 System Info.............................................................................................................................40
7.1.1 Information..............................................................................................................40
7.1.2 Log............................................................................................................................41
7.2 User Config .............................................................................................................................42
7.3 Network..................................................................................................................................44
7.3.1 Network ...................................................................................................................44
7.3.2 DDNS ........................................................................................................................46
7.3.3 SMTP / FTP...............................................................................................................48

iv
7.3.4 HTTPS .......................................................................................................................51
7.3.5 SNMP .......................................................................................................................54
7.3.6 Network Alarm.........................................................................................................54
7.4 Video ......................................................................................................................................55
7.4.1 Multi Streaming .......................................................................................................55
7.4.2 Camera.....................................................................................................................57
7.4.3 Advanced .................................................................................................................59
7.4.4 ROI (Region of Interest) ...........................................................................................63
7.4.5 Privacy Mask ............................................................................................................64
7.5 PTZ..........................................................................................................................................66
7.5.1 PTZ Control ..............................................................................................................66
7.5.2 PTZ OSD / Area.........................................................................................................72
7.5.3 Auto Tracking...........................................................................................................74
7.6 Audio ......................................................................................................................................78
7.7 User ........................................................................................................................................79
7.7.1 User Information......................................................................................................79
7.7.2 IP Address Filter .......................................................................................................81
7.8 Event.......................................................................................................................................82
7.8.1 Event Settings ..........................................................................................................82
7.8.2 Motion Detection.....................................................................................................86
7.8.3 Tamper Detection....................................................................................................87
7.8.4 Alarm I/O..................................................................................................................87
7.8.5 Schedule...................................................................................................................88
7.9 System ....................................................................................................................................89
7.9.1 Date/Time ................................................................................................................89
7.9.2 Daylight Saving.........................................................................................................90
7.9.3 SD Card.....................................................................................................................91
7.9.4 Maintenance............................................................................................................92
7.10 EKB200................................................................................................................................94
8. Upgrading Firmware Using IP Utility .....................................................................................96
9. Specifications................................................................................................................................98
10. Troubleshooting......................................................................................................................101
Appendix ...............................................................................................................................................104
A.Working in Conjunction with EverFocus’ EKB500 Keyboard.......................................................104
B.Tested Card Brands......................................................................................................................105
C.Enabling the Multicast Function..................................................................................................105

EPN4220d/4220di
1
1. Introduction
The EPN series is a high-performance IP speed dome supporting 20x optical-zoom and dual streams from
H.264 and MJPEG. The series comes in two types: outdoor (EPN4220d), indoor (EPN4220di). Equipped
with a weather-proof (IP66) and vandal-proof (IK10) housing, the outdoor models meet a wide variety of
needs for outdoor surveillance.
EverFocus IP speed dome provides Auto Tracking function to detect movement in the camera’s field of
view; and variable pan/tilt speeds ranging from 360° per second to 0.01° per second with 0.1° position
accuracy for fast and accurate monitoring. A maximum of 192 preset points can be configured for precise
location of target areas. Features like 360° endless rotation, 16 tour sequences, 4 patterns are all
provided.
The IP speed dome also features Wide Dynamic Range (WDR) function, which can provide clear images
even under back light circumstances where intensity of illumination can vary excessively. The DNR
(Digital Noise Reduction) function is designed for reducing the noises in the images, allowing the camera
to better distinguish between real motion and image noise, and thus results in a possibility to store more
video evidence on the connected storage devices.
A built-in micro SDHC card slot is also provided. You can power the camera by connecting the camera to
a 24 VAC power supply or a PoE switch. Since the EPN series IP speed dome conforms to ONVIF / PSIA for
compatibility with other network video devices, it interoperates with a wide variety of hardware and
software systems. You can also use EverFocus Mobile Applications to remotely view the live views of the
cameras through your handheld devices; or use EverFocus CMS to remotely manage multiple IP devices
connected on the network.
Outdoor
(EPN4220d)
Indoor
( EPN4220di)
Top Housing Top Housing
Outer Housing Outer Housing
Camera Main Body Camera Main Body
System Requirement
Before installing, please check that your computer meets this system requirement.
Operating System: Microsoft Windows XP / Vista (32-bit) / 7 (32-bit)
Microsoft Internet Explorer 7 or above
Note:For using the Internet Explorer, some settings are required. Please refer to 4.2 Settings for
Microsoft Internet Explorer.

EPN4220d/4220di
2
2. Features
Built-in H.264 / MJPEG digital signal output at 4CIF image size at up to 30 fps
Supports dual streams from H.264 / MJPEG
Supports MDI/MDI-X auto crossover
Bandwidth control: 256K ~ 6M bytes per second
Built-in network interface (10 / 100 Base-TX)
Smart Wizard settings for various event and schedule recording conditions
Built-in 20x optical AF zoom
True Day / Night function with removable IR cut filter
Low luminance for better image quality at night
Vandal-proof (IK10) for outdoor models
Weather-resistant (IP66-rated) for outdoor models
Auto Tracking
Motion Detection
Wide Dynamic Range (WDR)
Digital Slow Shutter (DSS)
Built-in Dynamic Noise Reduction (DNR)
Privacy Zone Masking
Excellent position accuracy of ±0.1 degree
From super slow [0.01°/sec] to very fast [360°/sec] pan/tilt speed
IP66-rated housings for all outdoor models
Maximum of 192 preset positions available
Supports directional virtual compass for easy operation
Programmable auto pan / 16 tours / 4 patterns
2 priority alarm inputs & 2 alarm outputs
Smart alarm reaction & resume after alarm
Enhanced auto-resume & power-up function
Digital flip function
One-click easy installation
Multi-languages on Web interface
ONVIF / PSIA compliant
Supports EverFocus CMS and Mobile applications (iOS / Android)
Supports eZ Tracker function: combining a fisheye and speed dome cameras for easy tracking and
smooth PTZ with 360° surround view*

EPN4220d/4220di
3
* The eZ Tracker is a cutting-edge technology that realizes the synergy of EverFocus network fisheye
and speed dome cameras. With eZ Tracker, users can control the speed dome camera through fisheye
camera Web UI. This technology not only obtains advantages from both types of cameras but also
creates new value for wide-area surveillance without compromising the optimal image quality. For more
details about the eZ Tracker function, please refer to the EFN Series Fisheye Camera User’s Manual.
Fisheye Window Speed Dome Window

EPN4220d/4220di
4
3. Installation
3.1 Packing List
The main box contains 3 boxes and a small box. Each box contains the items as listed below. Please check
that there is no missing item in the package before installing.
•Box 1: Top housing with a network connector and tool packet
Tool packet (Indoor only):
-Plastic anchor x 6
-Screw x 6
•Box 2: Camera main body with a tool packet
Tool packet
-Glove x 1 pair
-Desiccant pack x 3
-Power terminal block x 1
•Box 3: Outer housing
•Small Box: Power adapter
•Software CD x 1
•Quick Installation Guide x 1
Note:
1. Equipment configurations and supplied accessories vary by country. Please consult your local
EverFocus office or agents for more information. Please also keep the shipping carton for possible
future use.
2. Contact the shipper if any items appear to have been damaged in the shipping process.

EPN4220d/4220di
5
3.2 Optional Accessories
•EPTZ- PBOX (External power connection box) •Corner mount adapter
(Used for fixing a wall-mount bracket to a
90° wall corner, indoors or outdoors.)
•Pole mount adapter
(Used for installing a wall-mount bracket to a
pole, indoors or outdoors.)
•Indoor ceiling pendant mount bracket
(Used for installing a speed dome against
a ceiling.)
•Outdoor sunshield •Indoor recessed mount bracket
•Wall mount bracket •Indoor concrete ceiling mount adapter
(Used for attaching a speed dome to a
concrete ceiling.)
•EKB500 (RS-485 Keyboard) •EKB200 (USB controller keyboard)

EPN4220d/4220di
6
3.3 Cable Descriptions
1
2
3
4
5
6
7
RS-485+ (Yellow)
RS-485- (Orange)
24 VAC~
Video Test-Out Cable
Audio Out (Green)
Audio In (Blue)
LAN / PoE
No Name Description
1 RS-485+ Connects to an RS-485 device, such as EverFocus’ EKB500 keyboard.
2 RS-485-Connects to an RS-485 device, such as EverFocus’ EKB500 keyboard.
3 24 VAC~
Connects to the power adapter. Note that different regions may use
different ranges for AC voltage. Be sure to check the voltage range in
your area before installing.
4 Video Test-Out
Cable (BNC) Connects to a DVR or monitor.
5 Audio Out (Green) Connects to the speakers. See Note below.
6 Audio In (Blue) Connects to the microphones. See Note below.
7 LAN / PoE Connects to a 10/100 Ethernet or PoE.
Note: For details on working in conjunction with EverFocus’ EKB500 keyboard, please refer to
Appendix A.
Note that the audio in/out cables feature line 3.5mm jack (TRS). Be sure to prepare speakers /
microphones with TRS connector (see TRS Connector image below). Also, speakers / microphones with
a (built-in) amplifier and external power supply are required.
TRS Connector
Left Channel (Tip)
Right Channel (Ring)
Ground (Sleeve)
To activate the Audio function, the Enable Audio must be checked.
See 7.6 Audio in the User’s Manual.

EPN4220d/4220di
7
3.4 I/O Terminal Block
The I/O terminal block, located on the rear panel of the Base Board, can be used to develop
applications for alarm input and output, motion detection, PTZ control or a variety of other functions.
CON3
1 2 3 4 5 6 7 8 9 10 11 12
Pin Assignment
No.
Functions
No.
Functions
1
GND (-)
8
Alarm In 1
GND (-)
2
Alarm Out B
NO (+) 9 Alarm In (+)
3 COM (-) 10 Alarm In 2 GND (-)
4
NC (+)
11
Alarm In (+)
5
Alarm Out A
NO (+) 12 GND (-)
6
COM (-)
7
NC (+)

EPN4220d/4220di
8
3.5 Basic Installation for Outdoor Models
There are two ways to install the outdoor models of EPN series IP Speed Dome: Wall Mount and
Ceiling Mount.
3.5.1 Installation Requirements
The installation should be handled by a qualified service agent and should be complied with all
local regulations. Service personnel should check potential problem such as surfaces strength,
surface materials, falling objects, outer breaches, building vibration and other similar
conditions.
Check for all necessary materials, and ensure that the selected installation location is suitable
for the camera.
Bracket base
Bracket
Top housing
Main body

EPN4220d/4220di
9
3.5.2 Important Note for Installation
Before installing, insert a micro SD card into the main body and replace the 3 desiccant bags inside
the top housing. The desiccant bag loses its effectiveness after you open the camera. To keep the
camera’s interior dry, it is highly recommended to replace the desiccant bags every time when you
open the camera.
3.5.2.1 Replacing the Desiccant Bags
1. On the Top Housing, slightly press the black plastic socket backward and lift up the base
board.
2. Remove the desiccant bags from the top housing.
3. Stick the supplied 3 new desiccant bags inside the top housing.
Note: Ensure Not to place the desiccant bags under the position of the fan.
4. Insert the base board into the black plastic socket. The base board should click firmly into
position. Make sure the pin connector on the base board is lined up with the pin connector
on the main body when you press the two together.

EPN4220d/4220di
10
3.5.2.2 Inserting a Micro SD Card
1. Unscrew the four screws on the camera main body to remove the black housing.
Micro SD
Card Slot
2. Insert the micro SD card to the micro SD card slot.
3. Screw back the black housing.
3.5.2.3 Restoring to Factory Default
There are two ways to restore all of the camera’s settings to factory default values: 1. Click the
Default button on the Maintenance settings page, please refer to 7.9.4 Maintenance. 2. Press the
Reset Button on the camera main body, shown as below:
Press the Rest Button to
restore to factory default.

EPN4220d/4220di
11
3.5.2.4 Optionally Setting Up the DIP Switch
To allow the control device, such as a keyboard, to recognize and then control multiple cameras,
you need to set up the ID address for the cameras using the DIP switch on the Camera Main Body.
You can also set up the Protocol and Baud Rate for the cameras.
Note: Please ensure to turn off the power when setting up the DIP Switch. The new values will
only take effect after restarting the camera.
DIP Switch
Camera Main Body
ID Address
The ID address of the camera should be set to correspond properly with the control device, such
as a keyboard. The eight switches on the right correspond with the binary code of the ID address,
allowing up to 256 ID addresses (0 ~ 255) to be set up. Please refer to the sticker on the camera
main body or the following diagram for setting up the ID address. The default ID address is 1.
DIP Switch
Sticker on the Camera Main Body

EPN4220d/4220di
12
ON
12345678
Switch Address
1
ON
12345678
2
ON
12345678
3
ON
12345678
4
ON
12345678
5
ON
12345678
6
ON
12345678
7
ON
12345678
8
ON
12345678
9
ON
12345678
10
ON
12345678
11
ON
12345678
12
ON
12345678
Switch Address
13
ON
12345678
14
ON
12345678
15
ON
12345678
16
ON
12345678
17
ON
12345678
18
ON
12345678
19
ON
12345678
20
ON
12345678
21
ON
12345678
22
ON
12345678
23
ON
12345678
24
ON
12345678
25
ON
12345678
26
ON
12345678
27
ON
12345678
28
ON
12345678
29
ON
12345678
30
ON
12345678
31
ON
12345678
Switch Address
33
ON
12345678
34
ON
12345678
35
ON
12345678
36
ON
12345678
37
ON
12345678
38
ON
12345678
39
ON
12345678
40
ON
12345678
41
ON
12345678
42
ON
12345678
43
ON
12345678
44
ON
12345678
45
ON
12345678
46
ON
12345678
47
ON
12345678
48
ON
12345678
49
ON
12345678
50
ON
12345678
51
ON
12345678
52
ON
12345678
53
ON
12345678
54
ON
12345678
55
ON
12345678
56
ON
12345678
57
ON
12345678
58
ON
12345678
59
ON
12345678
60
ON
12345678
61
ON
12345678
62
ON
12345678
63
Switch Address Switch AddressSwitch AddressSwitch Address Switch AddressSwitch Address
ON
12345678
Switch Address
65
ON
12345678
66
ON
12345678
67
ON
12345678
68
ON
12345678
69
ON
12345678
70
ON
12345678
71
ON
12345678
72
ON
12345678
73
ON
12345678
74
ON
12345678
75
ON
12345678
76
ON
12345678
Switch Address
77
ON
12345678
78
ON
12345678
79
ON
12345678
80
ON
12345678
81
ON
12345678
82
ON
12345678
83
ON
12345678
84
ON
12345678
85
ON
12345678
86
ON
12345678
87
ON
12345678
88
ON
12345678
89
ON
12345678
90
ON
12345678
91
ON
12345678
92
ON
12345678
93
ON
12345678
94
ON
12345678
95
ON
12345678
Switch Address
97
ON
12345678
98
ON
12345678
99
ON
12345678
100
ON
12345678
101
ON
12345678
102
ON
12345678
103
ON
12345678
104
ON
12345678
105
ON
12345678
106
ON
12345678
107
ON
12345678
108
ON
12345678
109
ON
12345678
110
ON
12345678
111
ON
12345678
112
ON
12345678
113
ON
12345678
114
ON
12345678
115
ON
12345678
116
ON
12345678
117
ON
12345678
118
ON
12345678
119
ON
12345678
120
ON
12345678
121
ON
12345678
122
ON
12345678
123
ON
12345678
124
ON
12345678
125
ON
12345678
126
ON
12345678
127
Switch Address
ON
12345678
0
ON
12345678
32
ON
12345678
64
ON
12345678
96

EPN4220d/4220di
13
ON
12345678
Switch Address
129
ON
12345678
130
ON
12345678
131
ON
12345678
132
ON
12345678
133
ON
12345678
134
ON
12345678
135
ON
12345678
136
ON
12345678
137
ON
12345678
138
ON
12345678
139
ON
12345678
140
ON
12345678
Switch Address
141
ON
12345678
142
ON
12345678
143
ON
12345678
144
ON
12345678
145
ON
12345678
146
ON
12345678
147
ON
12345678
148
ON
12345678
149
ON
12345678
150
ON
12345678
151
ON
12345678
152
ON
12345678
153
ON
12345678
154
ON
12345678
155
ON
12345678
156
ON
12345678
157
ON
12345678
158
ON
12345678
159
ON
12345678
Switch Address
161
ON
12345678
162
ON
12345678
163
ON
12345678
164
ON
12345678
165
ON
12345678
166
ON
12345678
167
ON
12345678
168
ON
12345678
169
ON
12345678
170
ON
12345678
171
ON
12345678
172
ON
12345678
173
ON
12345678
174
ON
12345678
175
ON
12345678
176
ON
12345678
177
ON
12345678
178
ON
12345678
179
ON
12345678
180
ON
12345678
181
ON
12345678
182
ON
12345678
183
ON
12345678
184
ON
12345678
185
ON
12345678
186
ON
12345678
187
ON
12345678
188
ON
12345678
189
ON
12345678
190
ON
12345678
191
Switch Address Switch AddressSwitch AddressSwitch Address Switch AddressSwitch Address
ON
12345678
Switch Address
193
ON
12345678
194
ON
12345678
195
ON
12345678
196
ON
12345678
197
ON
12345678
198
ON
12345678
199
ON
12345678
200
ON
12345678
201
ON
12345678
202
ON
12345678
203
ON
12345678
204
ON
12345678
Switch Address
205
ON
12345678
206
ON
12345678
207
ON
12345678
208
ON
12345678
209
ON
12345678
210
ON
12345678
211
ON
12345678
212
ON
12345678
213
ON
12345678
214
ON
12345678
215
ON
12345678
216
ON
12345678
217
ON
12345678
218
ON
12345678
219
ON
12345678
220
ON
12345678
221
ON
12345678
222
ON
12345678
223
ON
12345678
Switch Address
225
ON
12345678
226
ON
12345678
227
ON
12345678
228
ON
12345678
229
ON
12345678
230
ON
12345678
231
ON
12345678
232
ON
12345678
233
ON
12345678
234
ON
12345678
235
ON
12345678
236
ON
12345678
237
ON
12345678
238
ON
12345678
239
ON
12345678
240
ON
12345678
241
ON
12345678
242
ON
12345678
243
ON
12345678
244
ON
12345678
245
ON
12345678
246
ON
12345678
247
ON
12345678
248
ON
12345678
249
ON
12345678
250
ON
12345678
251
ON
12345678
252
ON
12345678
253
ON
12345678
254
ON
12345678
255
Switch Address
ON
12345678
160
ON
12345678
192
ON
12345678
224
ON
12345678
128

EPN4220d/4220di
14
Protocol
The first, second and the third switches on the left are used to set the communication protocol.
Please refer to the sticker on the camera main body for setting up the protocol. The supported
protocols are listed on the sticker, including EVF, Pelco-D, Pelco-P, A-Type and Panasonic. The
default protocol is EVF.
DIP Switch
Sticker on the Camera Main Body
Note: If you switch the three protocol switches to ON, the camera will enter a self-test mode.
Baud Rate
The fourth and fifth switches on the left are used to set the baud rate (transmission speed).
Please refer to the sticker on the camera main body for setting up the baud rate. The default
baud rate is 9600.
DIP Switch
Sticker on the Camera Main Body