EverFocus EZA1840 eZ.HD Series User manual

EZA1840 eZ.HD Series
8MP IP66 IR Bullet Camera
User’s Manual
Copyright © EverFocus Electronics Corp.
Release Date: September, 2019
All the images including product pictures or screen shots in this document are for example
only. The images may vary depending on the product and software version. Information
contained in this document is subject to change without notice.
EverFocus Taiwan:
2F., No.12, Ln. 270, Sec. 3, Beishen Rd., Shenkeng Dist., New Taipei City 222, Taiwan
TEL: [phone] FAX: [phone] www.everfocus.com.tw
All manuals and user guides at all-guides.com
all-guides.com

1
1. Introduction
EverFocus eZ.HD series cameras – EZA1840 is equipped with a 8MP CMOS sensor.
The model provides 4mm fixed lens with ICR. Featured with True Wide Dynamic
Range (T-WDR), the camera can provide clear images even under backlight
circumstances where intensity of illumination can vary excessively. The EZA1840
supports both NTSC and PAL scanning systems (auto detection) and is IP66
certified.
1.1 Packing List
Camera x 1
Mounting Sticker x 1
L-Type Wrench x 1
Screw & Screw Anchor x 3
User Manual x 1
1.2 Features
Equipped with 8MP CMOS sensor
4mm fixed lens with ICR to capture the desired field of view
Extended IR range of up to 40m / 131ft. with 4 LEDs (depends on scene IR
reflectivity)
T-WDR to improve the visibility under high contrast scene
The flexible angle viewing with its 3-Axis rotation design allows wall or
ceiling mounting
IP66-rated with metal housing
Supports UTC function: Control camera OSD settings from DVR end
1.3 Dimensions
70mm / 2.76"
157mm / 6.18" 66mm / 2.6"
All manuals and user guides at all-guides.com

2
1.4 Optional Accessory
BA-E310
Color / Material: White / Metal
Size (Φ x H): 101 x 52mm / 3.98”x 2”
Weight: 540g / 1.2lb
1.5 Cable Description
12VDC Power Cable
Video Output Cable (BNC, 75Ohm)
2. Installation
1. Stick the supplied Mounting Sticker to the surface to mark the 3 screw
positions. Drill 3 holes on the surface and insert the supplied 3 Screw Anchors
into the screw holes. If you want to run the cable through the surface, drill a
hole within the 3 screw area.
2. To mount the camera to the surface, screw the Camera Base to the surface
using the supplied 3 Screws.
Mounting
Surface
Screws Screw Anchors
Camera Base
3. Connect the Power Cable to a 12VDC power source. Connect the Video
Output Cable to a monitor or DVR.
4. You can use the Joystick on the cable to configure camera OSD settings.
Remove the Protection Cap from the Joystick before using it.
All manuals and user guides at all-guides.com

3
UP
DN
Configuring OSD Settings:
•Push the Joystick up / down to select among
menu items.
•Push the Joystick left / right to adjust the level of
the selected item.
•Press the Joystick to enter the submenu or exit
the OSD Setup Menu.
5. You can optionally adjust camera angles. To do so, loosen the Rotate Screw
on the bracket using the supplied L-Type Wrench to adjust camera angles.
After adjusting camera angles, tightly screw back the Rotate screw.
Rotate Screw
All manuals and user guides at all-guides.com

4
3. Configuration in the OSD Menu
No
Main
Sub Menu
Sub Menu / Function
1 Edge Det On
Level
0-10
Color
YEL, CYN, GRN, MAG, RED, BLU, BLK,
WHT
Off
2 Exposure
Brightness
0-20
Shutter
Auto
Mode
Normal / Deblur
Manual Speed
1/30, 1/60, 1/120, 1/250,
1/500, 1/1000, 1/2000,
1/4000, 1/8000, 1/15000,
1/30000
Flicker
Sens-Up
Not supported
AGC
0-10
3 Backlight
HLC
Level
0-20
Color
YEL, CYN, GRN, MAG, RED, BLU, BLK,
WHT
BLC
H-POS
0-38
V-POS
0-35
H-SIZE
0-38
V-SIZE
0-35
WDR
WDR Mode
Line
ROI Mode
Box
Window Zone
0-3
Window Use
On, Off
H-POS
0-3856
V-POS
0-2176
H-SIZE
0-3856
V-SIZE
0-2176
Polygon
Window Zone
0-3
Window Use
On, Off
POS0-X
0-935
POS0-Y
0-360
POS1-X
0-935
POS1-Y
0-360
POS2-X
0-935
POS2-Y
0-360
POS3-X
0-935
POS3-Y
0-360
Off
Weight
High, Middle, Low
Off
4 Day/Night Mode
Auto
IR LED
Adaptive, Off
Anti-Sat.
0-20
D>N Thres
0-20
N>D Thres
0-20
Delay
High, Middle, Low
Color
B/W
IR LED
Adaptive, Off
Anti-Sat.
0-20
D>N Thres
0-20
All manuals and user guides at all-guides.com

5
N>D Thres
0-20
Delay
High, Middle, Low
Extern
IR LED
Adaptive, Off
Anti-Sat.
0-20
Extern SW
High, Low
D>N Thres
0-20
N>D Thres
0-20
Delay
High, Middle, Low
5 Color AWB
Auto
Autoext
Preset
Manual
C-Temp
3000K, 5000K, 8000K
R-Gain
0-20
B-Gain
0-20
Color Gain
0-20
6
DNR
High, Middle, Low, Off
7 Image
Sharpness
0-10
Gamma
0.45, 0.55, 0.65, 0.75
Mirror
On, Off
Flip
On, Off
D-Zoom
Not supported
ACE
High, Middle, Low, Off
Defog On
Mode
Auto, Manual
Level
High, Middle, Low
Off
Shading
On
Weight
0%-100%
Off
Privacy
Box On
Zone Num
0-15
Zone Disp
On, Off
H-POS
0-120
V-POS
0-68
H-Size
0-120
V-Size
0-68
Y Level
0-120
CB Level
0-68
CR Level
0-120
Trans
0-68
Off
Polygon On
Zone Num
0-7
Zone Disp
On, Off
POS0-X
0-240
POS0-Y
0-136
POS1-X
0-240
POS1-Y
0-136
POS2-X
0-240
POS2-Y
0-136
POS3-X
0-240
POS3-Y
0-136
Y Level
0-20
CB Level
0-20
CR Level
0-20
Trans
0-3
All manuals and user guides at all-guides.com
all-guides.com

6
Off
8 Motion On
Det Window
Window Use
0-3
Window Zone
On, Off
Det H-POS
0-96
Det V-POS
0-56
Det H-Size
0-96
Det V-Size
0-56
Sensitivity
0-10
Motion OSD
On, Off
Text Alarm
On, Off
Signal Out
On, Off
Off
9 System
Output
Frame Rate
4K/15fps, 4MP/30fps, 1080p/30fps
Freq
60Hz (auto detection)
Analog Mode
AHD, TVI, CVI, CVBS
Confirm
Yes
Return
Exit
Image Range
Full
Comp
User
Offset
0-32
Color Space
HD-CbCr, SD-CbCr, YUV
Audio Mic
Not supported
Color Bar
On, Off
Language
ENG, CHN, CHN(S), JPN, KOR, POR, ESP
Cam Title
Left-Down
Right-Up
Off
Reset
On
10
Exit
All manuals and user guides at all-guides.com