EverFocus ED910F User manual

ED910F & ED930F
1080p Full High Definition
True Day/Night Indoor Dome Camera
User’s Manual
Copyright © EverFocus Electronics Corp.
Release Date: February 2016

2
Precautions
1. Do not install the camera near electric or magnetic fields. Install the camera away from
TV/radio transmitters, magnets, electric motors, transformers and audio speakers since the
electromagnetic fields generated from these devices may distort the video image or
otherwise interfere with camera operation.
2. Never disassemble the camera beyond the recommendations in this manual nor introduce
materials other than those recommended herein. Improper disassembly or introduction of
corrosive materials may result in equipment failure or other damage.
3. Try to avoid facing the camera toward the sun. In some circumstances, direct sunlight may
cause permanent damage to the sensor and/or internal circuits, as well as creating
unbalanced illumination beyond the capability of the camera to compensate.
4. Keep the power cable away from water and other liquids and never touch the power cord
with wet hands. Touching a wet power cord with your hands or touching the power cord
with wet hands may result in electric shock.
5. Never install the camera in areas exposed to oil, gas or solvents. Oil, gas or solvents may
result in equipment failure, electric shock or, in extreme cases, fire.
6. Cleaning. For cameras with interchangeable lenses, do not touch the surface of the sensor
directly with the hands. Use lens tissue or a cotton tipped applicator and ethanol to clean
the sensor and the camera lens. Use a damp soft cloth to remove any dirt from the camera
body. Please do not use complex solvents, corrosive or abrasive agents for cleaning of any
part of the camera.
7. Do not operate the camera beyond the specified temperature, humidity or power source
ratings. This camera is suitable for indoor operation only. Use the camera at temperatures
within -10°C~50°C (14°F~122°F) and humidity less than 80%; this device is not rated as
submersible. The input power source is 12VDC or 24VAC. Be sure to connect the proper + / -
polarity and voltage, as incorrect polarity or too high a voltage will likely cause the camera
to fail, and such damage is not covered by the warranty.
8. Mounting. Use care in selecting a solid mounting surface which will support the weight of
the camera plus any wind, snow, ice or other loading, and securely attach the camera to the
mounting surface using screws and anchors which will properly support the camera. If
necessary (e.g. when mounting to drop ceilings) use a safety wire to provide additional
support for the camera.

3
Safety Notice
Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class A digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates uses and
can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct the interference by one of the
following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver
is connected.
- Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: Any changes or modifications not expressly approved by the party responsible for
compliance could void the user's authority to operate this equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause undesired operation.

4
Contents
1. Introduction...................................................................................................................... 5
1.1 Packing List .....................................................................................................................5
1.2 Features ..........................................................................................................................6
2. Cable Description.............................................................................................................. 6
3. Installation ....................................................................................................................... 7
3.1 Installation and Adjustment ...........................................................................................7
4. Configuration in the OSD Menu........................................................................................13
5. Specifications...................................................................................................................17

ED910F/ED930F eZ.HD Indoor Dome Camera
5
1. Introduction
The EverFocus eZ.HD Series ED910F/930F provides incredible performance in bright light
environments or low light, and the resolution listed in the specification from the actual camera you
install. To take full advantage of the amazing resolution available from this advanced imaging
technology, the Everfocus eZ.HD Series ED910F/930F uses a vari-focal lens together with 1/2.9" SONY
2.24M pixels CMOS to deliver 1080p high resolution together with a useable native low light
sensitivity of 0.08lux without using digital slow shutter. The camera truly provides optimized images
without compromising 1080p high resolution. The Digital Wide Dynamic Range function provides
clear color images in the most challenging of bright or unbalanced lighting conditions. The ED930F
camera also features 18 LEDs with range of 30m / 100 ft. and provides true day/night that enhances
images in low light environments with guaranteed ZERO ghosting. The cameras are equipped with
3-axis rotation mechanical design that delivers wall or ceiling mounting flexibility. Users can take the
advantage of vari-focal 2.8~12mm DC iris lens to easily adjustable field of view from the cameras.
The cameras also feature dual voltage operation and a full suite of OSD Menu and DSP functions
controllable at the camera (3DNR to save DVR HDD space, privacy masking, mirroring, and much
more). This is the camera that you have been waiting for to create analog CCTV systems that
produce astounding image clarity in a wide range of indoor applications at the widest range of light
levels. The ED910F/930F supports both NTSC and PAL scanning systems, which can be switched via
OSD.
Model Image Sensor Resolution IR LEDs Day / Night
ED910F 1/2.9" SONY 2.24M pixels
CMOS 1080p
No
True Day/Night
ED930F Yes (18 LEDs)
1.1 Packing List
Dome Camera x 1 Screw x 3
User Manual x 1 Screw Driver x 1
Test Lead x 1 Plastic Anchor x 3
DC Power Pigtail Cable x 1
Quick Installation Guide x 1
Template Plate x 1
Warning Paper x 1

ED910F/ED930F eZ.HD Indoor Dome Camera
6
1.2 Features
1080p with high flexibility and performance for astounding image
1/2.9" SONY 2.24M pixels CMOS Sensor, delivers amazing high sensitivity
Vari-focal 2.8~12mm DC iris lens to capture the desired field of view
18 IR LEDs for 30m/100ft. range -depending on scene IR reflectivity (for ED930F)
D-WDR to improve the visibility under high contrast scene
3D-Noise Reduction ensures less blurry moving subjects, vivid and high SN ratio images
even under low light environments
Support 1080p ,720p & 960H analog signal output, which can be easily switched using
OSD Joystick
The flexible angle viewing with its 3 Axis rotation design allows wall or ceiling mounting
Easy lock installation by screwing the base plate to the surface and then locking the
camera to the base plate without mounting screws
eZ.Controller function: Control camera OSD settings and PTZ operation directly from DVR
end
2. Cable Description
No. Name Descriptions
1 Power Cable Connect to a 12VDC or 24VAC power source.
2 Video Output 1080p, 720p and 960H output, using a 75 Ohm BNC-type
coaxial cable.
3 Test Lead Connect to a monitor for setting image aim and focus.
4 DC Power Pigtail Cable Optional power pigtail cable. The red wire is positive (+);
while the black wire is negative (-).

ED910F/ED930F eZ.HD Indoor Dome Camera
7
3. Installation
3.1 Installation and Adjustment
ED910F without LED ED930F with LED
Camera Breakdown

ED910F/ED930F eZ.HD Indoor Dome Camera
8
Important Notice
Please be noted the camera Base Plate may loosen when you take out the camera from the pack. It
is because the Base Plate is attached to the Camera Body without twisting tightly in order to
simplify the installation procedure.
1. Stick the Template Plate on the position where you want to attach the camera, drill three
holes on the Template Plate for screwing the camera with the supplied Screws and Plastic
Anchors. If you wish to run the wires through the wall / ceiling, drill an additional hole in
the middle “Line out” circle position. Otherwise you can wire the cables from the side cut
of the camera (refer to the “Line out” arrow position).
2. Insert the supplied three Plastic Anchors into the three holes.

ED910F/ED930F eZ.HD Indoor Dome Camera
9
3. Rotate counter-clockwise to remove the camera cap, press and pull to remove the liner.
Note: Hold the liner with one hand, then press and pull to remove the liner (refer to the “arrow”
marked on the liner)
4. Push the inner click outward and rotate the base plate counter-clockwise, then remove
the camera body from the base plate.(See the yellow arrow label on the camera)

ED910F/ED930F eZ.HD Indoor Dome Camera
10
5. Screw the base plate to the wall / ceiling using the supplied three Screws.
6. To screw the camera body back to the base plate, aim the arrow label of the camera body
to the arrow label of the base plate, and rotate the camera body clockwise. A “click”
sound should be heard when the camera body and the base plate are firmly locked.

ED910F/ED930F eZ.HD Indoor Dome Camera
11
7. Connect the camera to the 12 VDC or 24 VAC power source and an AHD DVR.
8. Optionally connect the camera to a monitor using the supplied Test Lead to adjust camera
angles, focus, zoom and configure OSD menu.
a. Connect one end of the Test Lead to the camera and the other end to a monitor.
b. To adjust camera angles, simply tilt, pan or rotate the camera.
c. To configure the OSD Menu, use the function button.

ED910F/ED930F eZ.HD Indoor Dome Camera
12
Note: The function button is using to control direction, and also to switch video format and
video output. Please follow the detailed instruction as below to switch the camera to:
Switch between 1080p and 720p (Default, 1080p): Press Upward for 5 Seconds
Switch from HD (1080p / 720p) to 960H: Press Left for 5 Seconds
Switch from 960H to HD (1080p / 720p): Press Right for 5 Seconds
Switch between NTSC and PAL: Press Downward for 5 Seconds
d. To adjust the Zoom / Focus, use the Zoom / Focus screws. Tighten the zoom /Focus
screws using the supplied Screw Driver.
9. Put the liner back and twist the camera cover cap back to the camera.

ED910F/ED930F eZ.HD Indoor Dome Camera
13
4. Configuration in the OSD Menu
You can use the function buttons on the rear panel of the camera body to configure camera settings
in the OSD menu:
No. Main Sub
Menu Sub Menu / Function
1 Lens DC Mode
Indoor
Outdoor
Min Shu. NTSC: 1/30
PA L : 1/2 5
Max. Shu.
NTSC: 1/60,FLK,1/240,
1/480,1/1000,
1/2000,1/5000,
1/10000, 1/50000
PAL: 1/50,FLK,1/200,
1/400,1/1000,
1/2000*,1/5000,
1/10000, 1/50000
Iris Speed 0 – 15
Manual
2 Exposure
Shutter
NTSC: 1/30, 1/60, FLK, 1/240, 1/480, 1/1000, 1/2000, 1
/5000, 1/10000,
1/50000, X2, X4, X6, X8, X10, X15, X20, X25, X30, Auto
PAL: 1/25, 1/50, FLK, 1/200, 1/400, 1/1000, 1/2000, 1/5000, 1/10000,
1/50000, X2, X4, X6, X8, X10, X15, X20, X25, X30, Auto
AGC 0 – 15
Sens-up Off
Auto Sens-up X2, X4, X6, X8, X10, X15, X20, X25, X30
Brightne
ss 1-100
D-WDR
Off
On Level 0-8
Auto
Defog
Off
Auto
Pos/Size Position, Size,↑,↓,→,←
Gradation 0-2
Default
3 Backlight Off

ED910F/ED930F eZ.HD Indoor Dome Camera
14
BLC
Level Middle, High, Low
Area Position, Size,↑,↓,→,←
Default
HSBLC
Select Area1, Area2, Area3, Area4
Display Off
On Position, Size,↑,↓,→,←
Black Mask On/Off
Level 0-100
Model All Day
Night AGC Level 0-255
Default
4White
Balance
ATW
AWC→SET
Indoor
Outdoor
Manual Blue 1-500
Red 0-100
AWB
5
Day &
Night
Ext D→N(Delay) 0-60
N→D(Delay) 0-60
Auto
D→N(AGC) 1-255
D→N(Delay) 0-60
N→D(AGC) 1-255
N→D(Delay) 0-60
Color
B/W
Burst Off/On
IR Smart
Off
On
Level 0-15
Area Position, Size,↑,
↓,→,←
IR PWM Off
0-100
6 NR 2DNR Middle/Low/Off/High
3DNR Middle/Low/Off/High
7 Special Cam Title
Off
On 0123456789ABCDEFGHIJKLMNOPQRSTUVWXYZ▶→
←↑↓()ˉ-_▊/=&:~,.
D-effect Freeze Off/On

ED910F/ED930F eZ.HD Indoor Dome Camera
15
Mirror Off, Mirror, V-flip, Rotate
Neg. Image Off/On
Motion
Off
On
Select Area1,Area2,Area3,Area4
Display On Position, Size,↑,↓,→,←
Off
Sensitiv
ity 0-100
Color Green, Blue, White, Red
Trans 1.00,0.75,0.50,
0.25
Alarm
View Type Off, Block, Outline, All
OSD View On/Off
Alarm Out On/Off
Time 1-15
Default
Privacy
Off
On
Select Area1,Area2,Area3,Area4
Display
Off
Color Position, Size,↑,↓,→,←
Mosaic Position, Size,↑,↓,→,←
Inv Position, Size,↑,↓,→,←
Color White, Black, Red, Blue, CYAN, Yellow,
Green
Trans 1.00,0.75,0.50,
0.25
Default
Language ENG/CHN1/CHN2/GER/FRA/ITA/SPA/POL/RUS/POR/NED/TUR
Defect
Live DPC
Off
On AGC level 0-255
Level 0-100
White DPC
Off
On
Pos/Size Position, Size,↑,↓,→,←
Start Close the iris then press
DPC View Off/On
Level 0-60
AGC 0-14

ED910F/ED930F eZ.HD Indoor Dome Camera
16
Sens-up x2, x4, x6, x8,x10, x15, x20,
x25, x30
Black DPC
Off
On
Pos/Siz Position, Size,↑,↓,→,←
Start Press Enter
DPC View Off/On
Level 0-255
RS485
CAM ID 0-255
ID Display Off/On
Baud Rate 2400,4800,9600,19200 ,38400
8 Adjust
Sharpness
Off
Auto
Level 0-10
Start AGC 0-255
End AGC 0-255
Monitor
CRT Blue Gain 0-100
Red Gain 0-255
LCD
Gamma
User,0.45,0.50,0.55,0.60,0.6
5,0.70,0.75,0.80,0.85,0.90,
0.95,1.00
Blue Gain 0-100
Red Gain 0-100
LSC Off/On
Video. Out PAL/NTSC
9 AF
AF Mode
Semi.
Auto
Manual
One Shot AF
TDN AF On
Off
Lens Init.
10 Exit Save& END /Reset/Not Saved

ED910F/ED930F eZ.HD Indoor Dome Camera
17
5. Specifications
Specifications and designs are subject to change for improving the functionality of this product
without notice.
P/N
ED910F
ED930F
Pickup Device
1/2.9" SONY 2.24M pixels CMOS
Video Format
NTSC and PAL( can be switched via OSD)
Effective Pixels
1920 (H)*1080 (V)
Scanning System
Progressive Scan
Sensitivity
0.01Lux/F1.4
0Lux with IR on
S/N Ratio Over 50 dB (AGC OFF)
Electronic Shutter AUTO, Manual (X30~1/ 50000), FLK
Video Output BNC 1.0Vp-p 75Ω
Gamma Correction
0.45
Lens Type
DC Iris 2.8-12mm, F1.4
BLC
OFF/BLC/HS BLC Selectable
AGC
0~15 Levels
White Balance
ATW/AWC-SET/INDOOR/OUTDOOR/MANUAL/AWB
Sync Mode
Internal
Day/Night
Ext, Auto, Color, B/W
IR LED N/A 18 Units
IR Distance N/A
Up to 30m/100ft. range(depending
on scene IR reflectivity)
OSD Languages
12-Language
Digital Noise Reduction
2DNR/3DNR, Off
Defog
Off/Auto
D-WDR On/Off
Sens-up Off/On(x30~x2)
Mirror Off/Mirror/V-Flip/Rotate
Motion Detection Off/On for 4 selectable zones
Privacy Mask Off/On for 4 selectable zones
Environmental
Indoor
Power Source
12VDC/24VAC
Power Consumption
12VDC:1.6w max./ 24VAC:
1.7w max.
12VDC:3.7w max./ 24VAC: 3.5w
max.
Operating Temperature -10°C~50°C / 14°F~122°F
Humidity Less than 80%
Dimensions(in/mm)
133 x 96.6mm / 5.24 " x 3.8"
Weight(lbs/g)
0.65lbs /295g
0.79lbs /360g
Certifications
CE/FCC/RoHS

ED910F/ED930F eZ.HD Indoor Dome Camera
18
EverFocus Electronics Corp.
EverFocus Taiwan:
12F-1, No.79, Sec. 1, Shin-Tai Wu Road,
Hsi-Chih, New Ta ip ei City, Taiwan
TEL: [phone]
FAX: [phone]
www.everfocus.com.tw
[e-mail]
EverFocus Europe - Germany:
Albert-Einstein-Strasse 1, D-46446
Emmerich, Germany
TEL: [phone]
FAX: [phone]
www.everfocus.de
[e-mail]
EverFocus China - Beijing:
Room 609, Technology Trade Building,
Shangdi Information Industry Base,
Haidian District, Beijing 100085, China
TEL: [phone]~39
FAX: [phone]
www.everfocus.com.cn
[e-mail]
EverFocus China - Shenzhen:
4F, No. 2, D4 Building, Wan Yelong
Industrial Park, Tangtou Road, Shiyan,
Baoan, Shenzhen, Guangdong 518101, China
TEL: [phone]
FAX: [phone]
www.everfocus.com.cn
[e-mail]
EverFocus USA - California:
1801 Highland Avenue, Unit A, Duarte, CA 91010,
USA
TEL: [phone]
FAX: [phone]
www.everfocus.com
[e-mail]
EverFocus Japan:
3F Kuramochi, Buildingll 2-2-3 Koto-Bashi,
Sumida-Ku Tokyo, 130-0022, Japan
TEL: [phone]
FAX: [phone]
www.everfocus.co.jp
[e-mail]
Your EverFocus product is designed and
manufactured with high quality
materials and components which can
be recycled and reused.
This symbol means that electrical and
electronic equipment, at their
end-of-life, should be disposed
ofseparately from your household
waste.
Please, dispose of this equipment at
your local community waste
collection/recycling centre.
In the European Union there are
separate collection systems for used
electrical and electronic product.
Please, help us to conserve the
environment we live in!
Ihr EverFocus Produkt wurde
entwickelt und hergestellt mit
qualitativ hochwertigen Materialien
und Komponenten, die recycelt und
wieder verwendet werden können.
Dieses Symbol bedeutet, dass
elektrische und elektronische Geräte
am Ende ihrer Nutzungsdauer vom
Hausmüll getrennt entsorgt werden
sollen.
Bitte entsorgen Sie dieses Gerät bei
Ihrer örtlichen kommunalen
Sammelstelle oder im Recycling
Centre.
Helfen Sie uns bitte, die Umwelt zu