EverFocus EMN2260 User manual

EMN2260 Outdoor Mini Fixed Dome Network Camera
2MP, H265, IR & WDR
Quick Installation Guide
Copyright © EverFocus Electronics Corp.
Release Date: January, 2020
All the images including product pictures or screen shots in this document are for example only.
The images may vary depending on the product and software version. Information contained in
this document is subject to change without notice.
EverFocus Taiwan:
2F., No.12, Ln. 270, Sec. 3, Beishen Rd., Shenkeng Dist., New Taipei City 222, Taiwan
TEL: [phone] FAX: [phone] www.everfocus.com.tw

1
1. Physical Description
1
2
3
4
No.
Item Name
Descriptions
1
Light Sensor
Detects lights.
2
IR LEDs
IR LEDs for infrared illumination in night vision applications.
3
Lens
Camera Lens.
4 Micro SD Card Slot
Insert a micro SD card. Please go to the product page on
EverFocus website to see the latest Storage Compatibility List.
http://www.everfocus.com.tw
Dimensions

2
Packing List
Please check that there is no missing item in the package before installing.
EMN2260
1. Camera x 1
2. MAC Address Sticker x 2
3. Cable Gland Kit x 1 (connect to the LAN/PoE cable for waterproofing)
4. Screw x 4 (to lock the upper cover)
5. Small Screw x 2 ( to lock the camera base and the mounting plate)
6. Screw Anchor x 4 (in conjunction with Screw)
7. Desiccant Bag x 1
8. Hexagon Wrench x 1
9. Mounting Sticker x 1
10.Quick Installation Guide x 1
11.Software CD x 1
Note:
1. Equipment configurations and supplied accessories vary by country. Please consult
your local EverFocus office or agents for more information. Please also keep the
shipping carton for possible future use.
2. Contact the shipper if any items appear to have been damaged in the shipping process.
Optional Accessory
You can go to the product page on EverFocus’ website to check the related optional
accessories. Please click Accessories on each Product page on EverFocus Website
www.everfocus.com.tw
2. Cables
The cables provide connections for network, power, audio input and output.
LAN / PoE Cable
12VDC Power Input
Audio Output
Audio Input

3
Note: To activate Audio function, the Audio function must be enabled please refer to 5.5.2
Video Streaming.
3. Installation
1. Before screwing the camera to the wall, stick the supplied Mounting Sticker on the wall /
ceiling to mark the position for installation. Drill four holes on the wall / ceiling according
to the supplied sticker and push the supplied four Screw Anchors into the four holes on
the wall / ceiling. Drill another hole in the middle of the Sticker if you wish to run the
wires into the wall / ceiling.
Wall / Ceiling

4
2. Check that the holes of the Mounting Sticker are correct.
Wall / Ceiling
3. There are two ways to tread the cables:
a. Through the wall / ceiling: run the cables through the hole on the wall / ceiling.
Wall / Ceiling
b. The other way is to cut the side of the mounting plate and fix the wire on it, the
placement can be arbitrarily placed on the top, bottom, left and right according to the
installation situation.
4. Connect the camera to power. You can either connect the camera to a 12VDC power
source or to a PoE switch using the PoE cable.
5. Connect the camera to the network using the supplied Cable Gland Kit.

5
a. Insert a RJ-45 network cable (without the RJ-45 connector on the one end) through
the supplied Waterproof Ring, Cable Gland, Stopper and Screw Cap accordingly.
Waterproof Ring Cable Gland Stopper Screw Cap
b. Connect the RJ-45 cable to the LAN/PoE Cable of the camera.
RJ-45 Cable
LAN/PoE Cable
c. Tightly screw the Cable Gland and Screw Cap to the Rugged RJ-45 Connector Cable.
Screw Cap
Cable Gland
d. Crimp the RJ-45 connector onto the RJ-45 network cable. Note that the wires should
be placed into the RJ-45 connector based on the following order (from left to right).
Orange with white stripe
Orange
Green with white stripe
Blue
Blue with white stripe
Green
Brown with white stripe
Brown
6. Remove the four screws of the upper cover through the supplied Hexagon Wrench.

6
7. Use two supplied Small Screws to lock the camera base and the mounting plate.
8. Optionally insert a micro SD card into the card slot (please refer to 2. Physical
Description).
9. Remove the screw to adjust the pan / tilt / rotate angles of the lens.
10.Before screwing back the camera cover, remove the 2 old desiccant bags from the inside
of Camera Cover and replace them with the supplied Desiccant Bag. Screw the camera
cover back to the camera.
Remove the 2 desiccant bags
Note: Please screw back the
Camera Cover immediately
in case of reducing the
absorption capacity of the
desiccant bag inside the
camera body.

7
11.After adjusting the direction and angle of the lens, tighten the upper cover screws.
Wall / Ceiling
12.The installation is complete.
Wall / Ceiling
4. Accessing the Camera
You can look up the IP address of the IP camera using the IP Utility (IPU) program, which is
included in the software CD.
The default network is DHCP. However, if there is no dynamic IP address assigned to the
device, its IP will switch to 192.168.0.10. By default, the ID is admin and there is no
password. Please input a password for the first-time login.
P/N: