EverFocus ES0812-31 User manual

ES0812-31
8-Port 10M/100M + 2-Port Giga uplink (1*TP+1*SFP)
Desktop Web Smart PoE Switch
User’s Manual
Copyright © EverFocus Electronics Corp,
Release Date: September, 2013
Notice: This content is subject to be changed without notice.

EVERFOCUS ELECTRONICS CORPORATION
PoE Switch
User’s Manual
2013 EverFocus Electronics Corp
www.everfocus.com
All rights reserved. No part of the contents of this manual may be reproduced or transmitted in any form
or by any means without written permission of the Everfocus Electronics Corporation.
Release Date: September, 2013
QuickTime is a registered trademark of the Apple Computer, Inc.
Windows is a registered trademark of the Microsoft Corporation.
Linksys is a registered trademark of the Linksys Corporation.
D-Link is a registered trademark of the D-Link Corporation.
DynDNS is a registered trademark of the DynDNS.org Corporation.
Other product and company names mentioned herein may be the trademarks of their respective owners.

Safety Precautions
FCC Warning
This Equipment has been tested and found to comply with the limits for a Class-A
digital device, pursuant to Part 15 of the FCC rules. These limits are designed to
provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses, and can radiate radio frequency energy.
It may cause harmful interference to radio communications if the equipment is not
installed and used in accordance with the instructions. However, there is no
guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is encouraged to
try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
CE Mark Warning
This is a Class-A product. In a domestic environment this product may cause radio
interference in which case the user may be required to take adequate measures.

Table of Contents
1. Introduction...................................................................................................... 1
1.1 Product Overview.................................................................................................1
1.2 Key Features .........................................................................................................1
1.3 Package ................................................................................................................4
2. Hardware Description ....................................................................................... 5
2.1 Product Outlook:..............................................................................................5
2.2 LED Indicators...................................................................................................6
2.3 Hardware Installation.......................................................................................6
2.4 Hardware Restore Button ................................................................................7
3 Preparation for Web Configuration ..................................................................... 8
4. Web Management Guide..................................................................................10
4.1 User Log In .....................................................................................................10
4.2 Administrator .................................................................................................12
4.2.1 Authentication Configuration .....................................................................12
4.2.1.1 System IP Configuration .......................................................................12
4.2.1.2 System Status .......................................................................................14
4.2.1.3 Load Default Setting.............................................................................15
4.2.1.4 Firmware Update .................................................................................16
4.3 Port Management ..............................................................................................18
4.3.1 Port Configuration....................................................................................18
4.3.2 Port Mirroring ..........................................................................................20
4.3.3 Bandwidth Control...................................................................................20
4.3.4 Broadcast Storm Control..........................................................................21
4.3.5 PoE ...........................................................................................................22
4.4 VLAN Setting ......................................................................................................24
4.4.1 VLAN Mode ..............................................................................................24
4.4.2 VLAN Member..........................................................................................25
4.4.3 Multi to 1 Setting .....................................................................................29
4.5 Per Port Counter ................................................................................................30
4.5.1 Port Counter................................................................................................30
4.6 QoS Setting.........................................................................................................32
4.6.1 Priority Mode ..............................................................................................32
4.6.2 Port, 802.1p, IP/DS based ...........................................................................33
4.6.3 TCP/UDP Port Based....................................................................................33
4.7 Security ..............................................................................................................35
4.7.1 MAC Address Binding..................................................................................35

4.7.2 TCP/UDP Filter.............................................................................................36
4.8 Spanning Tree.....................................................................................................38
4.8.1 STP Bridge Settings......................................................................................38
4.8.2 STP Port Settings .........................................................................................39
4.8.3 Loopback Detection Settings ......................................................................40
4.9 Trunking..............................................................................................................42
4.10 Backup/Recovery .............................................................................................44
4.11 Miscellaneous ..................................................................................................45
4.12 Logout ..............................................................................................................48
4.13 Q&A..................................................................................................................49

PoE Switch
1
1. Introduction
1.1 Product Overview
The switch is 8-port 10M/100M + 2 port Giga uplink (1*TP+1*SFP) Desktop
Web Smart PoE Switch, the switch supports IEEE 802.3at Power over Ethernet
standard, up to 30W per port, maximum 130W power consumption per system
and no special network cable required for your PD devices.
The switch also provides exceptionally smart Web management features, such
as VLAN, QoS, RSTP, LACP, Port Security…etc. The switch is designed for small or
medium network environment to strengthen its network connection. This
product is compact 11” size, making it ideal for Desktop users with limited space.
It also gives you the option of installing it in a 19” cabinet by rack-mount kits or
underneath a desk.
1.2 Key Features
Standard
Standard
IEEE 802.3 10BaseT
IEEE 802.3u 100BaseTX
IEEE 802.ab 1000BaseT
IEEE 802.3z 1000BaseSX/LX
IEEE 802.3x Full-duplex and Flow Control
IEEE 802.3ad Link Aggregation
IEEE 802.1Q VLAN
IEEE 802.1D Spanning tree protocol
IEEE 802.1p Class of Service
IEEE 802.1w Rapid Spanning tree protocol
IEEE 802.at Power over Ethernet (PoE+)

PoE Switch
2
Interface
Number of Port: 10
Fast Ethernet: 8-port 10/10 Base-TX with IEEE 802.3at PoE+
Gigabit Ethernet: 1-port 10/100/1000 Base-T, 1-port Gigabit SFP
Performance
MAC Address: Up to 4K
Buffer Memory: 2.75Mb
Transmission Method: Store and Forward Mechanism
Software Feature Description
Port Management
Port Configuration: Enable/Disable such as Link State, Speed/Duplex, Flow
Control, Address Learning; Monitor Link Status
Port Mirroring: One to one, one to many, many to one mirroring
Bandwidth Control: Up to 256 levels Bandwidth Control for TX and RX Rate
Broadcast Storm Control: Broadcast Storm Control and Threshold Setting
PoE Control: PoE Enable/Disable, PoE Status
Port Counter (Statistic): Monitor the port statistic
VLAN Setting
VLAN Mode: Port-based and Tag-based VLAN
Port Based VLAN: Up to 10 ports Port-Based VLAN
Tag Based VLAN: Up to 32 VLANs, Available DID from 1~4094
QoS Setting
Support High & Low Priority Queue
Priority Mode: First-In-First-Out, Strict and Weight-Round-Robin (WRR)
Priority Mode
Class of Service schemes: 802.1p,IP TOS/DS or Port Base
TCP/UDP Port & Priority queue mapping
Security Setting
Port Security - Port & MAC Address Binding, up to 3 MAC Address per port
TCP/UDP Filtering: Protocol Port Filter for secure WAN Port

PoE Switch
3
Spanning Tree Protocol
Version: Support Legacy Spanning Tree Protocol & Rapid Spanning Tree
Protocol
Loopback Detection: Loopback detection to avoid network loop.
Trunking
Trunking Type: Static Trunk or LACP
Trunk Group: 1, Gigabit Port 9 and Port 10 can be aggregated
LACP Long/Short Timeout time
IGMP Snooping V1&V2
Basic Features
Embedded HTTP web Management
User name/Password Authentication Configuration
Configuration Backup/Recovery
TFTP Firmware upgradeable
Secure Management
LED
LED Indicator
System: Power
Per Port: Link/ Act
PoE Port: Act/Status
Power
Power Input: 100~240V/AC, 50~60HZ
PoE Power Output: 802.3at compliant, 30W Max. per Port
Power Consumption: 130Watts (Max)
Product Dimensions/ Weight
Dimension : 44 × 266 × 160 mm (H x W x D)
Weight : 1.8kg

PoE Switch
4
1.3 Package
Before you start to install this switch, please verify your package that contains
the following items:
One Switch
One Power Cord
One User Manual CD
Optional Accessory:
11” to 19” Rack-mount kit

PoE Switch
5
2. Hardware Description
This section mainly describes the hardware of the Web-Smart Management PoE
Switch and gives a physical and functional overview on the certain switch.
2.1 Product Outlook:
Front Ethernet Ports: The front panel of the web smart switch consists of 8
10/100Base-TX RJ-45 ports,1 10/100/1000M RJ-45 and 1 Gigabit SFP uplink ports.
LED:The LED Indicators are also located on the front panel. They indicate the
System and Port Status.
Load Default Push Button: The button allows you to restore the configuration to
default.
Rear Panel
The 3-pronged power plug is placed at the rear panel of the switch right side
shown as below.
LED
Display
Gigabit Uplink
1x RJ-45/ 1x SFP Port
FE/PoE
RJ-45 Port
Load Default

PoE Switch
6
2.2 LED Indicators
The LED Indicators present real-time information of systematic operation status.
The following table provides description of LED status and their meaning.
LED
Color/Status
Description
Power
Amber On
Power on
10/100M
Link/ ACT
Green On
Link Up
Green Blinking
Data activating
PoE
Amber On
Port is linked to Power Device
Off
No Power Device is connected
1000M
(Port 9-10)
Green On
Link Up
Green Blinking
Data activating
2.3 Hardware Installation
Set the switch on a large flat space with a power socket close by. The flat space
should be clean, smooth, level and sturdy. Make sure there is enough clearance
around the switch to allow attachment of cables, power cord and allow air
circulation. The last, use twisted pair cable to connect this switch to your PC then
user could start to operate the switch.
AC Power Input
Connect the attached power cord to the AC power input connector, the available
AC power input is range from 100-264VAC.
Ethernet cable Request
The wiring cable types are as below.
10 Base-T: 2-pair UTP/STP Cat. 3, 4, 5 cable, EIA/TIA-568 100-ohm (Max. 100m)
100 Base-TX: 2-pair UTP/STP Cat. 5 cable, EIA/TIA-568 100-ohm (Max. 100m)
1000 Base-T: 4-pair UTP/STP Cat. 5 cable, EIA/TIA-568 100-ohm (Max. 100m)
PoE: To delivery power without problem, the Cat 5/5e and Cat 6 cable is

PoE Switch
7
suggested. The high quality Ethernet cable reduces the lost while power
transmission.
SFP Installation
While install the SFP transceiver, make sure the SFP type of the 2 ends is the same
and the transmission distance, wavelength, fiber cable can meet your request. It
is suggested to purchase the SFP transceiver with the switch provider to avoid any
incompatible issue.
The way to connect the SFP transceiver is to Plug in SFP fiber transceiver fist. The
SFP transceiver has 2 plug for fiber cable, one is TX (transmit), the other is RX
(receive). Cross-connect the transmit channel at each end to the receive
channel at the opposite end.
2.4 Hardware Restore Button
The purpose of this button is to provide a method for the network administrator
to restore all configurations to the default value.
To activate this function, the user should follow the following procedures.
(1) Press the “Load default” button for 3 seconds until you see all the LED blinking.
(2) When LED starts blinking, it means the CPU is executing the “load default”
procedure. You can release the button now.
After completing this procedure, all the factory default value will be restored. It
includes the IP address, the user name, the password and all switch
configurations.
Please noticed that the rest of the switch settings will be erased after this
procedure.

PoE Switch
8
3 Preparation for Web Configuration
The web management page allows you to use a standard web-browser such as
Microsoft Internet Explorer, Google Chrome or Mozila Firefox, to configure and
interrogate the switch from anywhere on the network.
Before you attempt to use the web user interface to manage switch operation,
verify that your Switch is properly installed on your network and that every PC on
this network can access the switch via the web browser.
Verify that your network interface card (NIC) is operational, and that your
operating system supports TCP/IP protocol.
Wire the switch power and connect your computer to the switch.
The switch default IP address is 192.168.2.1. The Switch and the connected PC
should locate within the same IP Subnet.
Change your computer’s IP address to 192.168.2.XX or other IP address which is
located in the 192.168.2.x (For example: IP Address: 192.168.2.30; Subnet Mask:
255.255.255.0) subnet.

PoE Switch
9
Launch the web browser and Login.
1. Launch the web browser (Internet Explorer or Mozila Firefox) on the PC.
2. Type http://192.168.2.1 (or the IP address of the switch). And then press
Enter.
3. The login screen will appear next.
4. Key in the password. Default user name and password are both admin.
If you can’t login the switch, the following steps can help you to identify the
problem.
1. Switch to DOS command mode and type the “ipconfig” to check the NIC’s
setting. Type the “ping 192.168.2.1”to verify a normal response time.
2. Check the security or Firewall settings, high security level may limit the web
access. Check with the IT people.
3. Try different Web-browser, like the Mozila or Google Chrome.

PoE Switch
10
4. Web Management Guide
4.1 User Log In
This part instructs user how to set up and manage the switch through the web
user interface. Please follow the description to understand the procedure.
At the first, open the web browser, and go to 192.168.2.1 site then the user will
see the login screen. Key in the password to pass the authentication then clicks the
OK.The log in process is completed and comes out the sign “Password successfully
entered”.
Log in
ID: admin
Password: admin
Figure 1-1
※Note: It will show error message if you key in wrong user name or password.
Figure 1-2

PoE Switch
11
Main Page
Figure 1-3

PoE Switch
12
4.2 Administrator
4.2.1 Authentication Configuration
This page shows authentication configuration information. User can set new
Username and Password in this page.
Figure 2-1
4.2.1.1 System IP Configuration
This page shows system configuration including the current IP address, Subnet
Mask and Gateway.
Figure 2-2
User can configure the IP settings, Subnet Mask, Gateway as below:
IP Address:Manually assign the IP address that the network is using. The
default IP is 192.168.2.1

PoE Switch
13
Subnet Mask: Assign the subnet mask to the IP address.
Gateway: Assign the network gateway for industrial switch.
IP Configure: Select the Static or DHCP.
The default setting is Static, you can manually configure the IP Address settings.
Select DHCP mode means the switch acts as the DHCP client and the switch will
try get the IP Address from the DHCP server.
Click Update to update the new settings.
It will show “update successfully” then press Reboot button. It will enter user
login screen automatically
Click DHCP -> Update, you can see the warning message.
Note: After changed to DHCP mode, the switch must be restarted to get new IP
address, however, since the switch only provide web management, it is hard for
user to find its new IP. Please don’t try this mode without pre-configured DHCP
setting in DHCP Server.

PoE Switch
14
4.2.1.2 System Status
This page displays the information about the switch of MAC address, how many
Physical Ports it has, System Version and Idle Time Security. Besides, users can
also fill in up to 15 characters in the Comment, Contact and Location field for note.
Figure 2-3
MAC Address: Displays the unique hardware address assigned by manufacturer
(default).
Number of Ports: Displays number of ports in the switch.
Comment:Add character here for not.
System Version:Displays the switch’s firmware version.
Idle Time Security: User can set the time security. When user leave the
computer for a moment, the software will auto logout or back to the last
display.
Click Update button to update the information. The system may request you to
restart the switch, please follow the instruction.
Figure 2-4 Time Out after the Idle Time Time Out

PoE Switch
15
4.2.1.3 Load Default Setting
Clicking the Load button will make the switch being set to the original
configuration.
Figure 2-4
※Note: It exclude to change user name, password and IP configuration. If you
want to restore default setting including IP and user name password, then you
can press the reset button for hardware base reset.
More detail information about Load Default Setting – Hardware Base is activated
by click Load Default Button. The procedure is described as following.
The purpose of this button is to provide a method for the network administrator
to restore all configurations to the default value.
To activate this function, the user should follow the following procedures.
(1) Press the “Load default” button for 3 seconds until you see all the LED blinking.
(2) When LED starts blinking, it means the CPU is executing the “load default”
procedure. You can release the button now.
After completing this procedure, all the factory default value will be restored. It
includes the IP address, the user name, the password and all switch
configurations.
Please noticed that the rest of the switch settings will be erased after this
procedure.