Everlight 19-237/R6GHBHC-A01/2T Instruction Manual

EVERLIGHT ELECTRONICS CO.,LTD.
Everlight Electronics Co., Ltd. http://www.everlight.com Rev. 1.0 Page: 1 of 12
Device No. : DSE-937-001 Prepared date: 03-04-2004 Prepared by : Jessica Chang
Technical Data Sheet
Full Color Chip LED
19-237/R6GHBHC-A01/2T
Features
․Package in 8mm tape on 7〞diameter reel.
․Compatible with automatic placement equipment.
․Compatible with infrared and vapor phase reflow
solder process.
․Multi-color type.
․Pb-Free.
Descriptions
․The 19-237 SMD Taping is much smaller
than lead frame type components, thus
enable smaller board size, higher packing
density, reduced storage space and finally
smaller equipment to be obtained.
․Besides, lightweight makes them ideal for
miniature applications. etc.
Applications
․Automotive: backlighting in dashboard and switch.
․Telecommunication: indicator and backlighting in
telephone and fax.
․Flat backlight for LCD, switch and symbol.
․General use.
Device Selection Guide
Chip
Type Material Emitted Color Lens Color
R6 AlGaInP Brilliant Red
GH InGaN Brilliant Green
BH InGaN Blue
Water Clear

EVERLIGHT ELECTRONICS CO.,LTD.
Everlight Electronics Co., Ltd. http://www.everlight.com Rev. 1.0 Page: 2 of 12
Device No. : DSE-937-001 Prepared date: 03-04-2004 Prepared by : Jessica Chang
19-237/R6GHBHC-A01/2T
Package Outline Dimensions
1.6
1.6
0.55
0.55
0.8
0.35
1.0
0.550.55
0.35
0.8
2.4
41
32
1
23
4
1.1
Anode mark
Red
Blue
Green
For reflow soldering (propose)
Note: The tolerances unless mentioned is ±0.1mm,Unit = mm

EVERLIGHT ELECTRONICS CO.,LTD.
Everlight Electronics Co., Ltd. http://www.everlight.com Rev. 1.0 Page: 3 of 12
Device No. : DSE-937-001 Prepared date: 03-04-2004 Prepared by : Jessica Chang
19-237/R6GHBHC-A01/2T
Absolute Maximum Ratings (Ta=25℃)
Parameter Symbol Rating Unit
Reverse Voltage VR5 V
Forward Current IF
R6:25
GH:25
BH:25
mA
Operating Temperature Topr -40 ~ +85 ℃
Storage Temperature Tstg -40 ~ +90 ℃
Soldering Temperature Tsol 260 (for 5
seconds) ℃
Power Dissipation Pd
R6:60
GH:110
BH:110
mW
Peak Forward Current
(Duty 1/10 @1KHz) IFP
R6:60
GH:100
BH:100
mA

EVERLIGHT ELECTRONICS CO.,LTD.
Everlight Electronics Co., Ltd. http://www.everlight.com Rev. 1.0 Page: 4 of 12
Device No. : DSE-937-001 Prepared date: 03-04-2004 Prepared by : Jessica Chang
19-237/R6GHBHC-A01/2T
Electro-Optical Characteristics (Ta=25℃)
Parameter Symbol Min. Typ. Max. Unit Condition
Luminous Intensity
R6
Iv GH
BH
72
112
28.5
100
180
50
----- mcd IF=20mA
Viewing Angle 2θ1/2 ----- 120 ----- deg IF=20mA
Peak Wavelength
R6
λp GH
BH
-----
632
518
468
----- nm IF=20mA
Dominant Wavelength
R6
λd GH
BH
-----
624
525
470
----- nm IF=20mA
Spectrum Radiation
Bandwidth
R6
△λ GH
BH
-----
20
35
35
----- nm IF=20mA
Forward Voltage
R6
VF GH
BH
-----
2.0
3.3
3.3
2.4
3.9
3.9
VIF=20mA
Reverse Current
R6
IRGH
BH
----- -----
10
50
50
μAVR=5V
Notes:
1.Tolerance of Luminous Intensity ±10%
2.Tolerance of Dominant Wavelength ±1nm
3.Tolerance of Forward Voltage ±0.1V

EVERLIGHT ELECTRONICS CO.,LTD.
Everlight Electronics Co., Ltd. http://www.everlight.com Rev. 1.0 Page: 5 of 12
Device No. : DSE-937-001 Prepared date: 03-04-2004 Prepared by : Jessica Chang
19-237/R6GHBHC-A01/2T
Typical Electro-Optical Characteristics Curves
R6

EVERLIGHT ELECTRONICS CO.,LTD.
Everlight Electronics Co., Ltd. http://www.everlight.com Rev. 1.0 Page: 6 of 12
Device No. : DSE-937-001 Prepared date: 03-04-2004 Prepared by : Jessica Chang
19-237/R6GHBHC-A01/2T
Typical Electro-Optical Characteristics Curves
GH

EVERLIGHT ELECTRONICS CO.,LTD.
Everlight Electronics Co., Ltd. http://www.everlight.com Rev. 1.0 Page: 7 of 12
Device No. : DSE-937-001 Prepared date: 03-04-2004 Prepared by : Jessica Chang
19-237/R6GHBHC-A01/2T
Typical Electro-Optical Characteristics Curves
BH

EVERLIGHT ELECTRONICS CO.,LTD.
Everlight Electronics Co., Ltd. http://www.everlight.com Rev. 1.0 Page: 8 of 12
Device No. : DSE-937-001 Prepared date: 03-04-2004 Prepared by : Jessica Chang
19-237/R6GHBHC-A01/2T
Label explanation
CAT: Luminous Intensity Rank
HUE: Dom. Wavelength Rank
REF: Forward Voltage Rank
Reel Dimensions
Note: The tolerances unless mentioned is ±0.1mm ,Unit = mm
19-237/R6GHBHC-A01/2T

EVERLIGHT ELECTRONICS CO.,LTD.
Everlight Electronics Co., Ltd. http://www.everlight.com Rev. 1.0 Page: 9 of 12
Device No. : DSE-937-001 Prepared date: 03-04-2004 Prepared by : Jessica Chang
Carrier Tape Dimensions: Loaded quantity 2000 PCS per reel
Note: The tolerances unless mentioned is ±0.1mm ,Unit = mm
Moisture Resistant Packaging
Aluminum moistue-proof bag LabelDesiccant
Label
19-237/R6GHBHC-A01/2T

EVERLIGHT ELECTRONICS CO.,LTD.
Everlight Electronics Co., Ltd. http://www.everlight.com Rev. 1.0 Page: 10 of 12
Device No. : DSE-937-001 Prepared date: 03-04-2004 Prepared by : Jessica Chang
Reliability Test Items And Conditions
The reliability of products shall be satisfied with items listed below.
Confidence level：90%
LTPD：10%
No. Items Test Condition
Test
Hours/Cycles Sample Size Ac/Re
1 Reflow Soldering
Temp. : 260℃±5℃
Min. 5sec. 6 Min. 22 PCS. 0/1
2 Temperature Cycle
H : +100℃15min
∫5 min
L : -40℃15min
300 Cycles 22 PCS. 0/1
3 Thermal Shock
H : +100℃5min
∫10 sec
L : -10℃5min
300 Cycles 22 PCS. 0/1
4 High Temperature
Storage Temp. : 100℃1000 Hrs. 22 PCS. 0/1
5 Low Temperature
Storage Temp. : -40℃1000 Hrs. 22 PCS. 0/1
6 DC Operating Life IF= 20 mA 1000 Hrs. 22 PCS. 0/1
7 High Temperature /
High Humidity 85℃/ 85%RH 1000 Hrs. 22 PCS. 0/1
19-237/R6GHBHC-A01/2T

EVERLIGHT ELECTRONICS CO.,LTD.
Everlight Electronics Co., Ltd. http://www.everlight.com Rev. 1.0 Page: 11 of 12
Device No. : DSE-937-001 Prepared date: 03-04-2004 Prepared by : Jessica Chang
Precautions For Use
1. Over-current-proof
Customer must apply resistors for protection , otherwise slight voltage shift will cause big
current change ( Burn out will happen ).
2. Storage
2.1 Do not open moisture proof bag before the products are ready to use.
2.2 Before opening the package, the LEDs should be kept at 30℃or less and 90%RH or less.
2.3 The LEDs should be used within a year.
2.4 After opening the package, the LEDs should be kept at 30℃or less and 70%RH or less.
2.5 The LEDs should be used within 168 hours (7 days) after opening the package.
2.6 If the moisture absorbent material (silica gel) has faded away or the LEDs have exceeded the
storage time, baking treatment should be performed using the following conditions.
Baking treatment : 60±5℃for 24 hours.
3. Soldering Condition
3.1 Pb-free solder temperature profile
3.2 Reflow soldering should not be done more than two times.
3.3 When soldering, do not put stress on the LEDs during heating.
3.4 After soldering, do not warp the circuit board.
4. Soldering Iron
Each terminal is to go to the tip of soldering iron temperature less than 280℃for 3 seconds
within once in less than the soldering iron capacity 25W. Leave two seconds and more intervals, and do
soldering of each terminal. Be careful because the damage of the product is often started at the time of
the hand solder.
19-237/R6GHBHC-A01/2T

EVERLIGHT ELECTRONICS CO.,LTD.
Everlight Electronics Co., Ltd. http://www.everlight.com Rev. 1.0 Page: 12 of 12
Device No. : DSE-937-001 Prepared date: 03-04-2004 Prepared by : Jessica Chang
5.Repairing
Repair should not be done after the LEDs have been soldered. When repairing is unavoidable, a
double-head soldering iron should be used (as below figure). It should be confirmed beforehand whether
the characteristics of the LEDs will or will not be damaged by repairing.
E
VERLIGHT ELECTRONICS CO., LTD. Tel: [phone]
Office: No 25, Lane 76, Sec 3, Chung Yang Rd, Fax: [phone]
Tucheng, Taipei 236, Taiwan, R.O.C http://www.everlight.com