Everpure dacor SCS-350 Manual


EV3123-65 Rev A DE07
Instruction Guide
SCS-350 Filtration/Decalcication Service Kit

 
Milk Cleaning
(Approx. 5 minute process)
Within two hours after last drink
containing milk
Plumed Model CM24P Quarterly
Routine Cleaning Weekly
Decalcification
(Approx. 30 minute process) Quarterly & Every 4000 cycles*
Service Call Every 4000 cycles*
*4000 cycles occur about every 2 years

 
ACDC10 Dacor Puly Decalcifying Powder for
use with model CM24T and CM24P
ACCLKIT Dacor Kit containing Puly Detergent
Tablets and Puly Liquid Detergent
A-302 Dacor Stainless Steel Cleaner
EV9798-15 ScaleKleen: Everpure Decalcifying
powder for use with model CM24P
**Available from Dacor Appliance dealers, Dacor Parts Distributors or
at www.everythingdacor.com

Phillips Screwdriver•
Wrench•
Utility Knife•
Measuring Tape•
Pencil•


Installation Parts
Key Description Part No.
1 QL3 Filter Head EV9258-31
2 SCS-350 Cartridge EV9270-20
3 JT Cartridge EV9608-51
4 Elbow Stud 4 mm EV3124-06
5 Adapter, 3/8" NPT x 1/4" BSPP EV3123-64
6 Angle Stop Valve Adaptor EV3121-20
7 Fixed Elbow EV3081-59
8Teflon®Tape EV3121-19
9 Tubing, 1/4” PF A08601-19
10 ScaleKleen (See above chart) EV9798-50
11 2CB-GW Cartridge* EV9618-31



Measure 22" from the base of the cabinet, and mark the mounting
location for the top of the filter head. Make sure there is adequate
space above the head to open and close the built in shut-off valve and
to avoid crimping the water line tubing. Also, make sure your chosen
location offers easy access for future cartridge changes.
 Use 2CB-GW cartridge in locations that do not require
hardness reduction. Order EV9618-31 separately.
 Width Height Depth
SCS-350 5" 22" 5"
JT Can 5" 15" 5"
2CB-GW* 5" 15" 5"
 The head and cartridge must be mounted in the vertical
position, with the cartridge hanging down.
A
1
2
8
5


9
4
3

•2•
C234
5
8
9
13 14
D

15


18
Label
Lug
19
E

Identify Filter Head and the two Fittings, and note inlet is1.
1/4" and the outlet is 4 mm.
Apply Teflon Tape2. ®to the threads of each Elbow Fitting.
Wrap tape in direction of the threads to assure a tight fit
and avoid small leaks.
Screw the 1/4" Inlet Elbow Fitting into the left side of the3.
filter head, and hand tighten only.
Screw the 3/8" NPT x 1/4" BSPP adapter onto the outlet4.
before screwing in the 4 mm Outlet Elbow Fitting into the
right side of the filter head.
Securely mount the filter head on the cabinet wall using5.
the enclosed mounting screws and washers.

Locate and close the cold water Angle Stop Valve. Open6.
cold water line of faucet to release water pressure.
Unscrew and disconnect the braided tubing on top of the7.
Angle Stop Valve .
Attach the bottom of Angle Stop Adaptor to the existing8.
cold water Angle Stop Valve.
Attach the braided tubing to the top of the Angle Stop9.
Adaptor.
Close side valve on Angle Stop Adaptor and open cold10.
water Angle Stop Valve to return water service to kitchen
sink. Check for leaks.
Connect 1/4" PF Tubing to water supply11.
Measure length of tubing needed to connect Angle12.
Stop Adaptor to Inlet Elbow Fitting on Filter Head. Allow
adequate tubing to avoid sharp turns.
Cut tubing at a 90° angle using a sharp knife.13.
Insert ends of tubing into quick-connect fittings. Push tube14.
into fitting and gently pull to confirm a tight fit.
Connect the 4 mm water line from the coffee machine to15.
the QL3 head with the 4 mm elbow stud on the outlet side
of the QL3

Lift handle of the built-in shut off in the QL3 head.15.
Hold head firmly with one hand.16.
Align cartridge lug with label on filter head.17.
Insert filter cartridge – Push upwards.18.
Turn it to the right – About 1⁄4 turn – Until rotation stops.19.
Open side valve of angle stop adaptor and check for leaks20.
up to inlet elbow fitting.
Turn water on at supply.21.
With the filtered water system in the ON position and with22.
the water retrieval vessel under the tea wand.
Begin rinsing process and press the tea button twice to23.
remove air.
Be sure to leave the drain water vessel in
position until the cleaning process is completed.
Push and hold the decaffeinated button until “Cleaner24.
Insert Cleaner” appears in the display.
Push the decaffeinated coffee button again to immediately25.
start the rinse cycle. If the decaffeinated coffee button is
not pushed again, the cleaning cycle will automatically
start in 20 seconds.
Run the clean cycle a second time after discarding the26.
rinse fluid from the drain water vessel.
15

•3•


Put a 2-quart container or retrieval vessel on the drip tray,1.
under the coffee dispenser to collect the wash and rinse
water.
Push and hold the CLEAN (decaffeinated coffee) button until2.
“Clean Insert Cleaner” appears in the display.
Push CLEAN again to immediately start the cleaning cycle. If3.
the CLEAN button is not pushed again, the cleaning cycle will
automatically start in about 20 seconds.
The coffee system will begin rinsing after the clean cycle4.
is done. When rinsing is complete, the display will read
“Machine Ready”. Press (cycle) the tea button once, and let
the machine sit with cleaning fluid in tank for 15 minutes.
After the cleaning cycle is complete, empty the cleaning5.
fluid from the retrieval vessel at the tea wand and return the
vessel to the tea wand for rinsing cycles.


Turn off water supply to the coffee system.1.
Slide the coffee system forward to access the regulator.2.
With the QL3 head permanently installed in series with the3.
existing water line and regulator, proceed to prepare the JT
cartridge.
Remove the diverter or cartridge installed on the QL3 head.4.
Remove the inlet tube from the JT sanitizing & flushing5.
cartridge with a small screw driver.
Lay the insert to the side and prepare the decalcification6.
powder for use in the JT cartridge.
Dissolve one packet of decalcification powder in 12 ounces7.
of warm water.
Fill sanitizing & flushing cartridge with decalcification8.
solution and top-off with water. Reinstall the inlet tube.
Install the sanitizing & flushing cartridge onto the QL3 head.9.
Keep upright so water does not run out.
Be sure the shutoff lever on the QL3 head is up and in the off10.
position (rotate until it stops). Turn the water back on at the
water source.
Now move the shutoff lever on the QL3 head down, to the on11.
position.

9
45
F
Bypass Diverter
4

With the retrieval vessel in place, cycle the tea (hot water)1.
button three times. Once complete, turn off the water at the
water filtration system head (Everpure QL3).
With the water turned off at the water filtration head, twist and2.
remove the decalcification cartridge (Everpure model JT) and
store for future use.
Install a new water filtration cartridge (Everpure model SCS-350,3.
H54, 2CB-GW or H300) into the water filtration system head and
turn the water on by moving the lever down on the QL3 head.
With the filtered water system in the ON position and with the4.
water retrieval vessel under the tea wand, begin the flushing
process.
Begin the rinsing process by pressing the tea button twice to5.
remove air.
Be sure to leave the drain water vessel in position
until the cleaning process is completed.
Push and hold the CLEAN (decaffeinated coffee) button until6.
“Clean Insert Cleaner” appears in the display.
Push the CLEAN (decaffeinated coffee) button again to7.
immediately start the rinse cycle. If the decaffeinated coffee
button is not pushed again, the cleaning cycle will automatically
start in about 20 seconds.
When the rinsing is complete, the machine will read “Machine8.
Ready”.
Proceed to rinse the tea wand by pressing the tea button once.9.
Repeat this process at least three times.
Taste a water sample from the drain water vessel checking for10.
any residual citrus flavors in the drain water. If after multiple
rinses you still taste residual citrus flavors in the rinse water
repeat the rinsing processes again.


1040MuireldDrive•HanoverPark,Illinois60133•800.323.7873
Toekomstlaan30•B-2200Herentals,Belgium
HashimotoMNBldg.7F•3-25-1HashimotoSagamihara-Shi•Kanagawa229-1103,Japan
Technical Service
800.942.1153
www.everpure.com
©2007 Everpure, LLC Printed in U.S.A. EV3123-65 Rev A DE07

You have just purchased one of the finest water treatment units made. As an expression of our confidence in Everpure products, this product is warranted against defects in material
and workmanship to the original end-user when installed in accordance with Everpure specifications. The warranty period commences from the date of purchase* and is administered
as follows:






The unit must be used in operating conditions that conform to Everpure’s recommended design guidelines. This warranty will not apply if the unit has been modified, repaired or altered
by someone not authorized by Everpure.
If a part described above is found defective within the specified period, you should notify Everpure technical service at the phone number listed below. Any part found defective within
the terms of this warranty will be repaired or replaced (at Everpure’s discretion) by your local dealer or Everpure technical service. You pay only freight from our factory and local
dealer charges. Any repaired or replaced warranty item will be incorporated under the original warranty terms of the existing system.
We are not responsible for damage caused by accident, fire, flood, freezing, Act of God, misuse, misapplication, neglect, oxidizing agents (such as chlorine, ozone, chloramines
and other related components), alteration, installation or operation contrary to our printed instructions, or by the use of accessories or components which do not meet Everpure’s
specifications. Refer to the specifications section in the Installation and Operating manual for approved application parameters.
Our product performance specifications are furnished with each water treatment unit. TO THE EXTENT PERMITTED BY LAW, EVERPURE DISCLAIMS ALL IMPLIED WARRANTIES,
INCLUDING WITHOUT LIMITATION WARRANTIES OF MERCHANTABILITY AND FITNESS FOR PARTICULAR PURPOSE; TO THE EXTENT REQUIRED BY LAW, ANY SUCH IMPLIED
WARRANTIES ARE LIMITED IN DURATION TO THE PERIOD SPECIFIED ABOVE FOR THE ENTIRE WATER TREATMENT UNIT. As a manufacturer, we do not know the characteristics of
your water supply or the purpose for which you are purchasing this product. The quality of water supplies may vary seasonally or over a period of time, and your water usage rate may
vary as well. Water characteristics can also differ considerably if this product is moved to a new location. For these reasons, we assume no liability for the determination of the proper
equipment necessary to meet your requirements, and we do not authorize others to assume such obligations for us. Further, we assume no liability and extend no warranties, express
or implied, for the use of this product with a non-potable water source or a water source which does not meet the conditions for use described in the owner’s guide or performance
data sheet for this product. OUR OBLIGATIONS UNDER THIS WARRANTY ARE LIMITED TO THE REPAIR OR REPLACEMENT (AT EVERPURE’S DISCRETION) OF THE FAILED PARTS OF
THE WATER TREATMENT UNIT, AND WE ASSUME NO LIABILITY WHATSOEVER FOR DIRECT, INDIRECT, INCIDENTAL, CONSEQUENTIAL, SPECIAL, GENERAL OR OTHER DAMAGES.
Some states do not allow the exclusion of implied warranties or limitations on how long an implied warranty lasts, so the above limitation may not apply to you. Similarly, some states
do not allow the exclusion of incidental or consequential damages, so the above limitation or exclusion may not apply to you. This warranty gives you specific legal rights, and you
may also have other rights which vary from state to state. Consult your telephone directory for your local independently operated Everpure dealer, or write Everpure for warranty and
service information.
Clean and maintain the coffee system regularly as
instructed in the Coffee System Maintenance Schedule. Clean it only in
the manner indicated in this manual. To prevent hazardous fumes and
drink contamination use only the cleaning agents specified.
Do not use a steam or pressure cleaner to clean the
coffee system or any part of it. Damage caused by cleaning the unit in
this manner could result in electric shock, fire, or explosion.
To avoid burns from hot surfaces, turn off the power
switch and allow the coffee system to cool at least 30 minutes before
cleaning.
To prevent sickness due to food poisoning, perform a
milk cleaning no more than two hours after making the last milk drink.
When cleaning mechanical parts of the coffee system,
exercise care with hands and arms around the metal edges.
Do not put any part of your coffee system in a dishwasher.
Many parts are not dishwasher safe.
Use only water with a hardness level of four grains per
gallon (GPG) or less when cleaning or making drinks with your coffee
system.
To properly decalcify a plumbed coffee system the water
supply must be interrupted between the water filtration system and the
coffee system regulator.
Compression fittings found in these locations are critical
to proper installation. Incorrectly installed fittings can cause serious
leakage.
When using decalcification powders avoid contact of these
solutions with any stainless steel surfaces including the coffee system,
counter tops, sinks, or other household appliances in the area.
If you currently use a home water filtration or softening
system you must install the bypass diverter assembly (model EV310876)
into the QL3 head immediately after removing the JT cartridge and
before turning on the water supply.
The Universal Plumbing Code adopted by over 20 states,
and other specific state and county codes prohibit the use of saddle
valves and their use is never recommended. You must adhere to your
state/local plumbing codes. Consult your licensed plumber if you have
related questions.
Do NOT use copper tubing with the John Guest Fittings
provided with your Everpure Filter System. Copper tubing may appear
to fit, but water leaks will develop over time and use. If copper tubing
is required, you must use copper compression fittings available from
any hardware/plumbing supply.