EVERVIEW EV2001SD User manual

FULL-MOTION TV WALL MOUNT
[e-mail]
EV2001SD

*
*
*
*
*
WARNING! SEVERE PERSONAL INJURY AND PROPERTY DAMAGE CAN RESULT FROM IMPROPER
INSTALLATION OR ASSEMBLY. READ THE FOLLOWING WARNINGS BEFORE BEGINNING.
If you do not understand the instructions or have any concerns or questions, please contact a qualified
installer.
Do not install or assemble if the product or hardware is damaged or missing. Not all parts and hardware
included must be used. If you require replacement parts, contact customer service at
[email protected].
This product has been designed for use on a vertical wall constructed of wood studs. Wood studs being
defined as a wall consisting of a minimum of 2” x 4” studs with a maximum of 24” stud spacing with a
maximum of 1/2” of wall covering (drywall, lath, plaster).For custom installations please contact a
qualified installer.
This product may contain moving parts. Use with caution.
DO NOT EXCEED THE MAXIMUM WEIGHT CAPACITY FOR THIS PRODUCT.
CAUTION!MAXIMUM WEIGHT CAPACITY
!80 lbs
(36.3kgs)
WARNING!
Tools Needed (Not Included)
Weight Capacity
USE WITH PRODUCTS LARGER THAN THE MAXIMUM WEIGHT AND SIZE MAY RESULT IN
INSTABILITY CAUSING POSSIBLE INJURY. USER MUST REMOVE TELEVISION OR OBJECT
OFF THE BRACKET BEFORE ADJUSTING. NOT SUITABLE FOR A TV THAT SURPASSES THE
TELEVISION MAXIMUM WEIGHT CAPACITY AND RECOMMENDED DIAGONAL MEASURED TV
SIZE!
Tape Measure Pencil Drill
1/2 in. (13 mm)
7/32 in. (5.5 mm)
Wood Drill
Screw Driver
Socket Wrench
Stud Finder
25/64 in. (10 mm)
Metric Wrench

1PC 2PCS
Supplied Hardware
A1 A2
Lag Bolts
5/16x2 in
38
Washers
ø8mm
D1 D2 E1 E2
Philips Screws
M6 x 12mm
M6 x 30mm
Philips Screws
M8 x 25mm
M8 x 50mm
B2
Spacers
L15mm
B1
Washers
ø6mm
C
Spacers
L5mm
x8
Philips Screws
M4 x 12mm
M4 x 30mm
x8
F1 F2
B3
bubble level
x1

Step 1 Before TV bracket installation
Measure the distance between the holes located
at the back of your TV(these measures may form
the shape of a square , or a rectangle) and check
that these taken measures are within the VESA(*)
range for this wall mount.
(*) VESA : International standard established by the
TV manufacturers used to determine if LCD/LED
TVs are compatible with wall mounts.
75 mm ≈ 2 7/8 in
100 mm ≈ 4 in
200 mm ≈ 7 7/8 in
300 mm ≈ 11 3/4 in
400 mm ≈ 15 3/4 in
Check TV Screws
Please select the proper screw length for your
TV by hand tightening to check your plat panel
thread depth.
When attaching brackets to the TV, be careful not to over tighten screws and be sure
that screws do not bottom out in the mounting holes.

TV
M4 x 12mm
F1
B1
M6 x 12mm
D1
M8 x 25mm
C
E1
TV
Step 2 Install TV bracket
for your reference
Manual Only!
Manual Only!
for your reference
TV
E2
B2
C
TV
B1
B2
C
or
F2 M4 x 30mm
D2 M6 x 30mm M8 x 50mm

3-2
Ensure marking at the
center of the stud.
Step 3
These anchors are for concrete or brick walls ONLY. DO NOT use them in
drywall or wood studs.
Ensure the wall plate is securely fastened to the wall before continuing on to the next step.
3-1
Use a stud finder (not included) to locate wood
stud. Mark the edge and center locations.
LEVEL

3-4
3-3
Drill 4 pilot holes using a 7/32 in. (5.5mm) diameter drill bit.
Make sure the depth is not less than 2 3/8" (60mm).er locations.
7/32in.
A1
Mount wall plate using 4 sets of 2 3/8 in lag bolts and
washers with a 1/2 in. socket wrench (not included).
A2
A1
A2
LEVEL

Step 4
Mounting your TV to the Brackets and lock it.
1
locking
2

Step 5 Post Installation Level
If needed, the TV can be leveled +/-3 degrees.
25/64 in. (10 mm)
Metric Wrench

Step 6 Tilt adjustment
Tilt adjustment
If mount can not tilt freely,
pls adjust the hardness of
nut in both sides.