EVEXPERT EVELINE MAX User manual
EVELINE MAX 11 kW MANUAL
EV Expert Portable charger 11kW
(for the European Union including Norway)
USER MANUAL
CONTENT
IMPORTANT SAFETY INSTRUCTIONS 3
CHARGER COMPONENTS 4
CONNECTING THE CHARGER 5
END OF CHARGING AND DISCONNECTING THE CHARGER 5
STATUS SIGNALING 6
PROBLEM-SOLVING 6
TECHNICAL SPECIFICATIONS 7
EU DECLARATION OF CONFORMITY 8
EVELINE MAX warranty conditions 9
Procedure for applying the warranty conditions 9
Additional provisions 10
IMPORTANT SAFETY INSTRUCTIONS
This document contains important instructions and warnings that must be observed when
using the portable charger for electric vehicles from EV Expert s.r.o.
WARNING
Read this document before using the charger. Failure to follow the instructions or warnings described in this
document may result in fire, electric shock, serious injury, or death.
➢The portable charger contains an RCD-A-EV circuit breaker and therefore a residual current device is
not necessary.
➢The EVELINE MAX portable charger is only designed for charging electric vehicles that support the IEC
62196-1 and IEC 61851-1 standard. Do not use it for other purposes or with other vehicles or objects.
➢The portable charger is only intended for vehicles that do not require ventilation during charging.
➢Before connecting the charger to the socket, make sure that it is rated for an adequate current load and
is not damaged.
➢Do not use the charger if it is defective, corroded or otherwise damaged, or if it indicates a serious
internal error.
➢Do not touch the connectors with sharp metal objects such as wires, needles or other tools.
➢Do not damage the charger with sharp objects or insert foreign objects into any part of the charger.
➢Keep the charger out of the reach of children or mentally incapable people.
➢When using and transporting the charger, handle it carefully to avoid damaging it. Do not subject it to
strong shocks, tension, twisting, tangling or loads.
➢Protect the charger, and especially its terminals, from moisture and water. Do not use it in heavy rain or
snow.
➢Make sure that the charging cable does not obstruct the movement of pedestrians, other vehicles or
other objects.
The charger must not be exposed to direct sunlight!
If a fault occurs, the user is not authorized to open, disassemble, repair or otherwise modify the device. If repair
is required, contact EV Expert s.r.o. or your dealer.
If you have any questions or recommendations, contact us at: [email protected]
CONNECTING THE CHARGER
1. Connect the charger to the mains to an industrial CEE socket. Do not use extension cables!
2. During the initialization phase, the red LED indicates that the TN-S network is selected. Blue indicates
that the IT network is selected.
3. If you need to change the selected network, press the button for 5 seconds during the initialization
phase to select the second network.
The user is solely responsible for the correct choice of network.
4. After correct detection of the PE conductor and successful initialization, the flashing white LED signals
the current setting of the maximum charging current.
1x
6A
2x
10A
3x
13A
4x
16A
5. Then the LED stays green and the charger is ready to charge.
6. Before connecting the electric car, it is possible to set the maximum charging current using the button.
When pressed, it changes color to either red or blue (depending on the type of network selected). The
number of presses determines the maximum charging current as in the initial signaling, ie one press
corresponds to a limit of 6A, two presses 10A, three 13A and four 16A. The fifth press sets the limit
back to 6A.
7. The number of presses is confirmed by the same number of flashes of the white LED.
If the supply is protected by less than 16A circuit breaker or there is a risk of concurrence with other
appliances, set an adequate maximum charging current. Limiting the maximum charging current is important to
prevent the circuit breaker from tripping. The charger remembers the last setting.
8. Connect the charger to the electric car.
9. Charging starts automatically.
END OF CHARGING AND DISCONNECTING THE CHARGER
NEVER disconnect the charger while charging!
1. First, stop charging on the side of the vehicle.
2. Unplug the charger from the grid.
3. If necessary, release the latch on the vehicle's charging port, and disconnect the charger from the
vehicle.
STATUS SIGNALING
The EVSE can signal several statuses during, before or after the charging process.
In general, a green-lit LED means that everything is ok. An orange-lit LED means that charging is underway. And
flashing LED means that there is a problem of some sort. The number of flashes depends on the type of problem.
Green/orange LED flashing – charging speed can be aected:
1x – problem with switching elements in the EVSE (rapid flashing)
2x – undervoltage or missing phases
3x – possible grid problems
4x – high temperature
Red LED flashing – charging will stop:
1x – problem with switching elements in the EVSE (rapid flashing)
2x – problem with the residual current device
3x – problem with the PE or neutral wire
4x – overvoltage
5x – very high temperature
6x – unsupported charging mode
All these statuses are also written on the device for easier identification of the problem.
PROBLEM-SOLVING
➢If charging slows down or suddenly stops, check the onboard system in the vehicle and the display on the
charger for an error condition. Then follow the reported error.
➢If charging has stopped, it may help to disconnect the portable charger from the car and the CEE socket
and reconnect it.
➢If the problem is caused by the high temperature of the charger, stop charging until the charger cools
down. Check that the charger is not exposed to direct sunlight, and if so, place it in the shade. If
overheating occurs regularly, contact EV Expert s.r.o. or your dealer.
In case of persistent problems, contact EV Expert s.r.o. at: [email protected]
TECHNICAL SPECIFICATIONS
Rated charging current
Max 1x16A or 3x16A* (11kW) – depending on the connector
Own consumption at rest
Less than 0,5W
Permissible ambient temperature
-40°C to +50°C
Degree of protection
Body and cable: IP65, plug-in terminals: IP44
Dimensions of the aluminum body
50 x 08 x 190mm (HxWxL)
Power supply terminal
CEE (red 5-pin for 16A)
Connector for electric vehicle
Type 1 or Type 2 in accordance with IEC 62196-2 to 32A
Phases used
1 or 3 depending on the vehicle
Manufactured in accordance with
IEC 62196, IEC 61851-1, CE, EMC, RoHS
Total length
5m or 7m
Compatible electrical network
TN-S, IT
RCDB (Integrated in the charger)
AC < 30mA / DC < 6mA
*The maximum current and charging time depend on the characteristics of the electric vehicle being charged. The charger
may limit the charging current at high temperatures.
EU DECLARATION OF CONFORMITY
WE
EV Expert s.r.o.
Polská 181 / 70
779 00, Olomouc
IČ: 056 99 711
as manufacturer, declare under our sole responsibility that the following referenced vehicle charging
products:
Portable charger EVELINE MAX
(serial number printed on the body of each charger)
is in conformity with the applicable requirements of the following directives:
2014/35/EU Low Voltage Directive
2014/30/EU EMC Directive
2011/65/EU Restriction of the use of certain hazardous substances in electrical and electronic
equipment
Conformity with these directives has been assessed for this product by demonstrating compliance
to the following harmonized standards and/or regulations:
●EN 61851-1:2010
●EN 62196-2
●EN 61000-6-3 ed.2:2007 + A1:2011
●EN 61000-6-1 ed.2:2007
●EN 61000-3-2
●EN 61000-3-3
The product is safe under normal and intended use conditions. We have taken all measures available to ensure the
conformity of products placed on the market with the essential requirements of European Union legislation.
In Olomouc, 5.1.2020
EVELINE MAX warranty conditions
1. EV Expert, sro (hereinafter "EV Expert") has developed a highly reliable device for charging electric vehicles,
called EVELINE MAX, which is designed to withstand normal operating conditions when used in accordance with
the operating manual (the “Manual”) supplied by EV Expert.
2. The EV Expert Limited Warranty (“Limited Warranty”) covers defects in workmanship and EVELINE MAX material
(“Defective Product”) for a period of two (2) years (“Warranty Period”) from the date of original purchase of the
Product.
3. The Limited Warranty does not apply and EV Expert assumes no responsibility for any defect or damage to any
EVELINE MAX that has been:
a. misused, neglected, altered or otherwise damaged, either internally or externally,
b. improperly operated, manipulated or used, including use under conditions for which the product was not
designed or used in an unsuitable environment or used in a manner inconsistent with EV Expert's
installation and operating manual or applicable laws and regulations
c. exposed to fire, water, corrosion, biological attack or input voltage that creates operating conditions
above the maximum or minimum limits specified in the EV Expert technical specifications, including
high input voltage from generators or lightning strikes,
d. exposed to accidental or consequential damage caused by defects in other components of the electrical
system,
e. if the original identification mark (including the trademark or serial number) of such EVELINE MAX has
been contaminated, altered or removed.
4. The limited warranty does not cover costs associated with troubleshooting of the customer's electrical systems.
The limited warranty does not exceed the original costs of EV Expert.
5. During the warranty period, EV Expert will, at its sole discretion, repair or replace a defective product free of
charge, provided that EV Expert inspects the existence of a defect covered by the limited warranty.
6. EV Expert will use new and / or repaired parts at its discretion when repairing or replacing a defective product.
EV Expert reserves the right to use parts or products of original or improved design when repairing or replacing a
defective product.
7. If EV Expert repairs or replaces a defective product, the limited warranty will continue on the repaired or
replacement product for the remainder of the original warranty period or ninety (90) days from the date of
return of the repaired or replacement product by EV Expert, whichever is later.
8. The limited warranty covers only parts and labor required to repair a defective product.
9. The Limited Warranty covers the cost of shipping a repaired or replacement product from EV Expert through a
carrier selected by EV Expert to locations within the European Union, but not to locations outside the European
Union. The limited warranty does not cover damage during transport or damage caused by improper handling by
the carrier. The carrier is responsible for such damages.
Procedure for applying the warranty conditions
1. To obtain repair or replacement under the limited warranty, the customer must follow a certified Return
Merchandise Authorization process.
2. All defective products must be returned with a Return Merchandise Authorization Number (RMAN), which the
customer must request from EV Expert.
The RMA request must contain the following information:
i. Proof of purchase of defective product
ii. Defective product model number
iii. Serial number of the defective product
iv. Detailed description of the defect
v. Shipping address for returning a repaired or replacement product.
3. Any defective product approved for return must be returned in the original shipping container or other packaging
that adequately protects the product from damage during shipment.
4. The returned defective product may not be disassembled or modified without the prior written consent of EV
Expert.
Additional provisions
1. The Limited Warranty is the only and exclusive warranty provided by EV Expert that is permitted by law. Its
meaning takes precedence over all other warranties, express or implied, statutory or otherwise, including
warranties of title, quality, merchantability, fitness for a particular purpose or warranties as to the accuracy,
eectiveness or suitability of any technical or other information provided in manuals or other documentation.
2. In no event shall EV Expert be liable for any special, direct, indirect, incidental or consequential damages, losses,
costs or expenses under contract, or restrictions on the commencement of any economic loss of any kind, any
loss or damage to property, or any personal injury.
3. To the extent that warranties relating to EVELINE MAX are required under applicable law, such implied warranties
will be limited in time to the Warranty Period to the extent permitted by applicable law. In states and provinces
that do not allow the limitation or exclusion of implied warranties or for the duration of the implied warranty, or
the limitation or exclusion of incidental or consequential damages, the above limitations or exclusions may not
apply.
4. This Limited Warranty gives the customer specific legal rights. The customer may have other rights that vary
from state to state or region to region.
Email contact address is [email protected]
Contact phone is +420 722 689 252
VAT ID: CZ05699711
Stupkova 18, 779 00 Olomouc
Czech Republic
For more information, visit our website: www.evexpert.eu or contact us at email: [email protected]
Table of contents
Other EVEXPERT Batteries Charger manuals
