evoheat EVO ULTRA Series User manual

[e-mail]
1300 859 933
www.evoheat.com.au
Evo Ultra Manual
Page 1
Contents
1. Introduction...............................................................................................................................................2
2. Unit Dimensions .......................................................................................................................................3
3. Safety Instructions ....................................................................................................................................4
4. Installation ................................................................................................................................................5
4.1 System Installation ..............................................................................................................................5
4.2 Plumbing.............................................................................................................................................5
4.3 Electrical Connection ..........................................................................................................................6
4.4 Initial Start-up......................................................................................................................................6
5. Operation..................................................................................................................................................7
5.1 The Controller .....................................................................................................................................7
5.2 Operating Functions............................................................................................................................7
5.2.1 Using the HELP Button.................................................................................................................7
5.2.2 Starting & Shutting Down..............................................................................................................7
5.2.3 Switching Modes ..........................................................................................................................7
5.2.4 System State Checking ................................................................................................................8
5.2.5 Changing Temperature.................................................................................................................8
5.2.6 Clock Setting ................................................................................................................................8
5.2.7 Timer Settings ..............................................................................................................................8
5.2.8 Keyboard Lock............................................................................................................................10
5.2.9 Malfunction Display.....................................................................................................................10
6. Troubleshooting......................................................................................................................................11
6.1 Fault Table........................................................................................................................................11
6.2 BHB10 Fault Table............................................................................................................................12
6.3 Possible Failures & Solutions............................................................................................................13
7. Appendix ................................................................................................................................................14
7.1 Parameter List...................................................................................................................................14
7.2 Cable Specifications..........................................................................................................................14
7.3 Wiring Diagrams................................................................................................................................15
7.4 Automatic Water Filling Valve............................................................................................................18
8. Maintenance...........................................................................................................................................19
9. Warranty.................................................................................................................................................20

[e-mail]
1300 859 933
www.evoheat.com.au
Evo Ultra Manual
Page 2
1. Introduction
This manual contains information relating to the installation, troubleshooting, operation, and maintenance of this
EvoHeat unit. Instructions in this manual must always be followed. Failure to comply with these recommendations will
invalidate the warranty. Should you have any questions or require technical support, call the EvoHeat office on 1300
859 933 to speak to our team.
The data and information contained in this manual is correct at the time of publishing and is subject to change without
notice. For the most up to date manual, contact EvoHeat directly.
The Evo Ultra is a water to water heat pump that is the perfect solution in
applications where chillers and cooling towers are being used for
temperature control. When installed in line with the chiller, the Evo Ultra can
capture rejected waste from the chiller return lines and utilise this heat to
provide FREE HOT WATER!
TECHNICAL DATA Evo Ultra 32 Evo Ultra 64 Evo Ultra 129
Evaporator Side
20°C/15°C
Condenser Side
45°C/55°C
Heating Capacity kW 34.4 68.8 137.6
Consumed Power kW 26 54.1 104.1
Power Input kW 8 16 32
C.O.P 4.3 4.3 4.3
Evaporator Side
20°C/15°C
Condenser Side
65°C/75°C
Heating Capacity kW 27.6 55.2 110.4
Consumed Power 20.1 40.3 80.3
Power Input kW 7.6 15 30.5
C.O.P 3.62 3.62 3.62
Voltage/Phase 380-415/3/50 380-415/3/50 380-415/3/50
Max. Running Current A 27 54 108
Rated Power Input kW 8.5 17 34
Max. Power Input kW 14.6 29.2 58.4
Noise dB(A) 65 68 69
Compressor Type Copeland Scroll ZW Series R134a EVI Scroll
Compressor No. 1 2 4
Evaporator Water Flow m3/h 3.3 6.8 13.6
Condenser Water Flow m3/h 2.7 5.6 11.1
Refrigerant Type R134a R134a R134a
Suggested Water Temp. Range °C 55 ~ 75 55 ~ 75 55 ~ 75
Max. Outlet Water Temp. °C 80 80 80
Net Weight kg 202 441 866
Net Dimensions (L/W/H) mm 1030 / 640 / 730 1172 / 900 / 1365 1600 / 1130 / 1500
Heating: Heat source side: water inlet/outlet temperature: 20°C/15°C User side water inlet/outlet temperature: 65°C/75°C
When the units work between 55-85°C, make sure the low-pressure range is between 0.27-0.65MPa and the evaporating temperature is between
7-30°C. The above data is for reference only, specific data is subject to the product nameplate

[e-mail]
1300 859 933
www.evoheat.com.au
Evo Ultra Manual
Page 3
2. Unit Dimensions
EVO ULTRA 32
EVO ULTRA 64
EVO ULTRA 129
Unit: mm A (L) B (W) C (H) D E F G H
Evo Ultra 32 1030 640 730 1000 980 640 443 400
Evo Ultra 64 1172 900 1365 850 850 812 750 680
Evo Ultra 129 1600 1130 1500 1080 1050 1000 800 410

[e-mail]
1300 859 933
www.evoheat.com.au
Evo Ultra Manual
Page 4
3. Safety Instructions
Installation, repair, or relocations must only be done by a fully qualified technician. If done incorrectly there is
a number of hazards that can occur including fire, electric shock, water leakage and injury.
•A circuit breaker must be installed for the unit.
•Ensure the unit has a good power connection and earthing to avoid the risk of electrical shocks.
•Maintenance and operation must be carried out according to the recommended time and frequencies, as
stated in this manual.
•The unit must be stored in a room without any continuously operating ignition sources (for example: open
flames, an operating gas appliance)
•Do not pierce or burn the unit.
•If the supply cord is damaged, it must be replaced by a qualified service agent.
•This appliance must be installed in accordance with national wiring regulations.
•Before obtaining access to terminals all supply circuits must be disconnected.
•Use supply wires suitable for 75°C
•The unit is equipped with an over-load protection system. After a previous stoppage, the unit will not start for
at least 3 minutes.
•For unit cleaning or maintenance, switch off and disconnect the power of the unit.
•Do not install the unit near flammable gas or spray flammable substances near it.
•Ensure the heat pump is installed on a strong and stable platform.
•If the supply cord is damaged, it must be replaced.
•Use genuine standard spare parts only.

[e-mail]
1300 859 933
www.evoheat.com.au
Evo Ultra Manual
Page 5
4. Installation
According to Reverse Carnot Cycle theory and the same process as normal water source heat pump units, The Evo
Ultra absorbs heat from soil and transfers the heat to water as the soil temperature is generally stable, i.e., the heat
source is stable, the units work capability will not change with the ambient temperature.
4.1 System Installation
• This model can be installed on a concrete base with expansion bolts or installed on the ground or roof by
a steel bracket with rubber cushion. Make sure that the units are horizontally placed.
• The units should be installed at a place convenient for installation and maintenance.
• The units should install shock-absorbing devices in case of the shock transferring to the building.
• Rigid pipelines in the engine room should adopt spring shock-absorbing brackets.
For transit, use four slings longer than 8m when moving the units and use the lifting holes on the bottom board. Put a
cushion block at the places of contact in case of damage.
4.2 Plumbing
When connecting the water pipeline, you cannot exchange the user side pipeline with the heat source side pipeline.
The unit’s user side and heat source side direction should be in accordance with the direction as marked on the units.
Water pipeline resistance out of the units should as minimal as possible.
The pipeline must be clean to prevent jamming. Before packing the insulation layer, a leakage test should be
conducted.
Adopt the same diameter water pipe as mentioned in the user guide for inlet and outlet connection pipe out of the
units. Ensure that the pipeline is full of water and has fine moisture measures when the unit is at work.
The Expansion water tank should be equipped at the highest part of the water pipeline. The water surface of the
expansion water tank should be 0.5m or higher than the highest point of water pipeline.
Choose the insulation water tank with suitable volume according to the units heating and cooling capacity and ensure
the insulation of pipeline out of the water tank.
If the units have no water pump equipped, please choose the proper water pump according to the units water flow
volume on the user guide, making sure the water flow volume satisfies the units requirement. There should be hose
connection equipment between the water pump and units. If the water pump is installed outdoors, there should be
water-proof and anti-freezing equipment.
An automatic exhaust air valve should be equipped at the highest point of the water pipeline in case of air detention in
the pipe; Drainage valve should be equipped at the lowest point of the water pipeline, so it can be convenient for
maintenance and drainage.
A Y-type filter should be installed at the circular water pump inlet port of the user side and heat source side in case
that impurities may damage the units. The Y-type filter should be detachable for cleansing and maintenance.
Softened water can be better for circular water.
The connection of the water inlet and outlet should be flexible to reduce vibration.
Drain out the water in the pipeline when you will not use the units for a long time in case of freezing.
Do not change the set return water temperature and water tank insulation temperature.
Thermometer and water pressure gauge should be equipped at the units water inlet and outlet port for checking.
User side water should be tap water and the hardness should be less than 20. If not, install an electric hydro treater at
the tap water side.

[e-mail]
1300 859 933
www.evoheat.com.au
Evo Ultra Manual
Page 6
4.3 Electrical Connection
IMPORTANT: Always use a qualified Electrician to perform any electrical work. A licensed electrician must read the
information before connecting.
Ensure the power cable and circuit breaker are of a suitable size for the heater being installed. Also check that there is
adequate voltage and current available at the heater connection to run the unit.
• Open the front panel and open the power supply access.
• The power supply must go through the wire access and be connected to the power supply terminals in the
controlling box. Then connect the 3-signal wire plugs of the wire controller and main controller.
• If an external water pump is required, please insert the power supply wire into the wire access and
connect it to the water pump terminals.
• If an additional auxiliary heater is needed to be controlled by the heat pump controller, the relay (or power)
of the aux-heater must be connected to the relevant output of the controller.
4.4 Initial Start-up
Pre-Start Inspection
• Check the indoor unit, make sure that the pipe connection is done correctly, and the relevant valves are
open.
• Check the water loop to ensure that the water inside of the expansion tank is filled to an appropriate level,
the water supply is working and that the water loop is full of water & free of trapped air. Make sure there is
good insulation for the water pipe.
• Check the electrical wiring. Make sure that the power voltage is normal, the screws are fastened, the
wiring is made in line with the diagram and that the earthing is connected.
• Check that the heat pump includes all the screws and components, and that they are in good order. When
powering the unit on, review the indicator on the controller to see if there is any indication of failure. The
gas gauge can be connected to the check valve to see the high pressure (or low pressure) of the system
during trial running.
Trial Operation
• Start the heat pump by pressing the ON/OFF key on the controller. Check whether the water pump is
running, if it runs normally there will be 0.2MPa on the water pressure meter.
• When the water pump has ran for a minute, the compressor will start. Listen for any strange sounds from
the compressor, if an abnormal sound occurs please stop the unit and check the compressor. If the
compressor runs well, please look for the pressure meter of the refrigerant.
• Check whether the power input and running current is in line with the manual. If not, please stop and
check.
• Adjust the valved on the water loop to make sure that the hot (cool) water supply to each door is good and
meets the requirements of heating (or cooling).
• Review whether the outlet water temperature is stable.
• The parameters of the controller are set by the factory, the user cannot change these themselves.

[e-mail]
1300 859 933
www.evoheat.com.au
Evo Ultra Manual
Page 7
5. Operation
5.1 The Controller
ON/OFF
Press this button to start up/shut off the unit,
cancel current operation or go back to previous
interface.
HELP Press this button to check button function of
system state.
MODE Press this button to change the current mode,
page up or confirm current operation.
CLOCK Press this button to set the clock or turn the timer
on/off.
UP Press this key to select the upwards option or
increase the parameter value.
DOWN Press this key to select the downwards option or
decrease the parameter value.
5.2 Operating Functions
5.2.1 Using the HELP Button
You can use at any interface and it will explain the buttons & functions of the current interface. To exit the help
interface, simply press the ON/OFF button.
EXAMPLE: Press HELP at the Main Interface
5.2.2 Starting & Shutting Down
To turn on/off the unit, press the ON/OFF button for 1 second. The screen will display as following for each state:
5.2.3 Switching Modes
At the main interface, you can switch between the
modes of cooling, economic heating, heating &
rapid heating by pressing
Example: Switch from Cooling mode to Economic Heating
Note: The operation of mode is invalid if the unit you purchase is heating only or cooling only.
Welc ome
V1. 0
v1.0
Lo ading.. ... .

[e-mail]
1300 859 933
www.evoheat.com.au
Evo Ultra Manual
Page 8
5.2.4 System State Checking
At any interface you can enter the system working state by pressing TWICE, then using the UP and DOWN arrow
keys to highlight the required parameter, then press to enter. To exit, press the ON/OFF button
5.2.5 Changing Temperature
At the main interface, press the UP or DOWN key to adjust the temperature setting as desired. Once complete, press
the button to save the settings and exit. Press the ON/OFF button to exit without saving settings. Refer to the
Parameter Table to set relevant temperature.
5.2.6 Clock Setting
At the main interface press to enter the clock setting interface. Select the parameter you wish to change and press
to make the parameter begin flashing which indicates it can be changed. Press the UP or DOWN keys to change
the parameter value, then press to save. Press the ON/OFF button to return to the main menu.
Note: If there is no operation after 10 seconds, it will return to the main menu and changes will automatically be saved.
To change the date, the same process is followed.
5.2.7 Timer Settings
Four timer periods can be set according to your needs.
From the main interface, press to enter the timer setting, press DOWN to select Timer, then press to enter the
timer setting interface.
The process of setting a timer is much the same as adjusting the Clock settings.
To cancel and return to the previous menu, press the ON/OFF button.

[e-mail]
1300 859 933
www.evoheat.com.au
Evo Ultra Manual
Page 9
5.2.7.1 Timer
Each timer has an ON value when the unit will turn on an OFF value when the unit will turn off (00:00-00:00).
These timers are required for the Daily Timers & Temperature Timers to work.
Example: TIMER1 Unit is on at 7:30am – and off at 10pm
5.2.7.3 Temperature Timer
The temperature timer will adjust the temperature as desired for your set Timer periods.
Example: If Timer 3 was set for 1pm – 5pm on a Monday, the unit would operate to the set temperature during the
timeframe on the Monday.
5.2.7.2 Daily Timer
The Daily Timer allows you to apply your timers to particular days of the week.
•OFF means that the unit will not run on that day.
•ON means the system will be running for a whole day.
•Applying one timer will have the unit run from A-B.
•Applying two timers will mean the unit runs from A-B, then C-D.
Example: Setting the operation on Friday to run two different timers.
If the Timer2 were 8am-10am & Timer 3 were 1pm-5pm, the unit would operate or stop accordingly.

[e-mail]
1300 859 933
www.evoheat.com.au
Evo Ultra Manual
Page 10
5.2.8 Keyboard Lock
You may wish to lock the keyboard to prevent unauthorised users from adjusting settings. When the keyboard is
locked, a small lock symbol will be displayed on the screen.
• To lock: from the main menu, hold the ON/OFF button for 5 seconds.
• To unlock: from the main menu, hold the ON/OFF button for 5 seconds.
. Note: If the unit is in alarm state, the keyboard lock is automatically removed.
5.2.9 Malfunction Display
If a fault occurs, there will be a malfunction code showing on the controller screen. Refer to the Malfunction Table (9.9)
to find out the failure cause and solutions.

[e-mail]
1300 859 933
www.evoheat.com.au
Evo Ultra Manual
Page 11
6. Troubleshooting
6.1 Fault Table
DISPLAY
FAILURE
REASON
SOLUTION
P01 Inlet temp. sensor failure
The temp. sensor is short circuit or
broken
Check or change the temp sensor
P02 Outlet temp. sensor failure
The temp. sensor is short circuit or
broken
Check or change the temp sensor
P04 Ambient temp. failure
The temp. sensor is short circuit or
broken
Check or change the temp sensor
P15(system1),
P25(system2),
P35(system3),
P45(system4)
System 1/2/3/4 Coil temp.
failure
The temp. sensor is short circuit or
broken Check or change the temp sensor
P17(system1),
P27(system2),
P37(system3),
P47(system4)
System 1/2/3/4 absorb temp.
failure
The temp. sensor is short circuit or
broken Check or change the temp sensor
P19(system1),
P29(system2),
P39(system3),
P49(system4)
System 1/2/3/4 anti-freeze
temp. failure
The temp. sensor is short circuit or
broken Check or change the temp sensor
P191(system1),
P291(system2),
P391(system3),
P491(system4)
Using side system 1/2/3/4 Anti-
freeze temp. failure
The temp. sensor is short circuit or
broken Check or change the temp sensor
P151(system1),
P251(system2),
P351(system3),
P451(system4)
System 1/2/3/4 coil inlet temp.
failure
The temp. sensor is short circuit or
broken Check or change the temp sensor
E11(system1),
E21(system2),
P31(system3),
E41(system4)
System 1/2/3/4 high pressure
protection The high-pressure switch is broken Check the pressure switch and
cold circuit
E12(system1),
E22(system2),
E32(system3),
E42(system4)
System 1/2/3/4 low pressure
protection The low-pressure switch is broken Check the pressure switch and cold circuit
E03 Water flow failure No water/little water in water system
Check the pipe waterflow and
water pump
E04
Electric-heater overheat
protection
Electrical-heat is overheat Check or change electrical-heat
E06 Water inlet and oulet temp. too
big
Water flow is not enough and low
differential pressure
Check the pipe waterflow and
whether water system is jammed
or not
E06 System 1/2/3/4 anti-freeze
protection
Water flow is not enough and low
differential pressure
Check the pipe waterflow and
whether water system is jammed
or not
E17(system1),
E27(system2),
E37(system3),
E47(system4)
System 1/2/3/4 source side
anti-freeze protection Water flow is not enough
Check the pipe waterflow and
whether water system is jammed
or not
E171(system1),
E271(system2),
E371(system3),
E471(system4)
System 1/2/3/4 using side anti-
freeze protection Water flow is not enough
Check the pipe waterflow and
whether water system is jammed
or not
E19
Anti—freeze protect level 1
The ambient temp. is low
/
E29
Anti—freeze protect level 2
The ambient temp. is low
/
E05 System protection The protection system is failure
Check each protection point of the
system
E08 Communication Failure Communication failure between wire
controller and mainboard
Check the wire connection
between remote wire controller
and main board

[e-mail]
1300 859 933
www.evoheat.com.au
Evo Ultra Manual
Page 12
6.2 BHB10 Fault Table
CODE FAILURE REASON SOLUTION
P181 System 1 exhaust temp. failure The sensor is open or short
circuited Check or change the sensor
P281 System 2 exhaust temp. failure The sensor is open or short
circuited Check or change the sensor
P04 Ambient temp. sensor failure The sensor is open or short
circuited Check or change the sensor
E171 System 1 anti-freeze temp. failure The sensor is open or short
circuited Check or change the sensor
E271 System 2 anti-freeze temp. failure The sensor is open or short
circuited Check or change the sensor
P101 System 1 economizer inlet temp.
failure
The sensor is open or short
circuited Check or change the sensor
P201 System 2 economizer inlet temp.
failure
The sensor is open or short
circuited Check or change the sensor
P102 System 1 economizer outlet temp.
failure
The sensor is open or short
circuited Check or change the sensor
P202 System 2 economizer outlet temp.
failure
The sensor is open or short
circuited Check or change the sensor
P19 System anti-freeze protection Water flow volume not enough Check the flow volume, see if water is
jammed or not
P29 System 2 anti-freeze protection Water flow volume not enough Check the flow volume, see if water is
jammed or not
E08 Communication failure
Communication failure between
remote wire controller and main
board
Check the wire connection between remote
wire controller and main board
E151 System 1 current protection Current through compressor
too heavy
Check through the power supply for
compressor or short circuit
E251 System 2 current protection Current through compressor
too heavy
Check through the power supply for
compressor or short circuit
P182 System 1 exhaust high temp.
protection
Compressor exhaust temp. too
high Check through the refrigerant system
P282 System 2 exhaust high temp.
protection
Compressor exhaust temp. too
high Check through the refrigerant system
INDICATOR DISPLAY
Fault Indicator
System 1 1 Flashes 1 OFF
System 2 2 Flash 1 OFF
Ambient Temp. 3 Flash 1 OFF

[e-mail]
1300 859 933
www.evoheat.com.au
Evo Ultra Manual
Page 13
6.3 Possible Failures & Solutions
Failure Possible Causes for the Failure Solutions
Heat pump cannot be
started
Wrong power supply
Shut off the power and check power supply
Power supply cable loose
Check power cable and make right connection
Circuit breaker open
Check for the cause and replace the fuse or
circuit breaker
Water pump is running
with high noise or without
heater
Lack of water in the piping
Check the water supply and charge water to the
piping
Too much air in the water loop
Discharge the air in the water loop
Water valves closed
Open the valves in the water loop
Dirt and blockage on the water
filter
Clean the water filter
Heat pump capacity is
low, compressor does not
stop
Lack of refrigerant
Check for the gas leakage and recharge the
refrigerant
Bad insulation on water pipe
Make good insulation on water pipe
Low heat exchange rate on air side
exchanger
Clean the air side heat exchanger
Lack of water flow
Clean the water filter
High compressor exhaust
Too much refrigerant
Discharge the redundant gas
Low heat exchange rate on air side
exchanger Clean the air side heat exchanger
Low pressure problem of
the system
Lack of gas Check the gas leakage and recharge freon
Block on filter or capillary
Replace filter or capillary
Lack of water flow
Clean the water filter and discharge the air in
water loop
Compressor do not run
Power supply failure
Check off the power supply
Compressor contactor broken
Replace compressor contractor
Power cable loose
Tighten the power cable
Protection on compressor
Check the compressor exhaust temp
Wrong setting on return water temp
Reset the return water temp
Lack of water flow
Clean the water filter and discharge the air in
water loop
High noise of compressor
Liquid refrigerant goes into
compressor
Bad evaporation, check the cause for bad
evaporation and fix
Compressor failure Use new compressor
Fan do not run
Failure on fan relay
Replace the fan relay
Fan motor broken Replace fan motor
The compressor runs but
heat pump has no heating
or cooling capacity
No gas in the heat pump Check system leakage and recharge refrigerant
Heat exchanger broken
Find out the cause and replace the heat
exchanger
Compressor failure Replace compressor
Low outlet water
temperature
Low water flow rate
Clean the water filter and discharge the air in
water loop
Low setting for the desired water
temp
Reset the desired water temperature
Low water flow protection Lack of water in the system
Clean the water filter and discharge the air in
water loop
Failure on flow switch
Replace the flow switch

[e-mail]
1300 859 933
www.evoheat.com.au
Evo Ultra Manual
Page 14
7. Appendix
7.1 Parameter List
Meaning Default Remarks
Set-point of cooling target temperature 12 Adjustable
Set-point of heating target temperature 60°C Adjustable
Set-point of auto mode target temperature 27°C Adjustable
7.2 Cable Specifications
Single Phase Unit
Nameplate maximum current
Phase line
GND Line
Breaker
Creepage Protector
Signal Line
No more than 10A 2 x 1.5mm21.5mm220A
30mA less than 0.1 sec n x 0.5mm2
10~16A 2 x 2.5mm22.5mm232A
16~25A
2 x 4mm
2
4mm
2
40A
25~32A 2 x 6mm26mm240A
32~40A 2 x 10mm210mm263A
40~63A 2 x 16mm216mm280A
63~75A 2 x 25mm225mm2100A
75~101A 2 x 25mm225mm2125A
101~123A 2 x 35mm235mm2160A
123~148A 2 x 50mm250mm2225A
148~186A 2 x 70mm270mm2250A
186~224A 2 x 95mm295mm2280A
Three Phase Unit
Nameplate maximum current Phase line GND Line Zero Line Breaker
Creepage
Protector
Signal Line
No more than 10A 3 x 1.5mm21.5mm21.5mm220A
30mA less than
0.1 sec n x 0.5mm2
10~16A 3 x 2.5mm22.5mm22.5mm232A
16~25A 3 x 4mm24mm24mm240A
25~32A 3 x 6mm26mm26mm240A
32~40A 3 x 10mm210mm210mm263A
40~63A 3 x 16mm210mm216mm280A
63~75A 3 x 25mm216mm225mm2100A
75~101A 3 x 25mm216mm225mm2125A
101~123A 3 x 35mm216mm235mm2160A
123~148A 3 x 50mm225mm250mm2225A
148~186A 2 x 70mm235mm270mm2250A
186~224A 2 x 95mm250mm295mm2280A
The above specification is applicable for 3-core cable wire made of copper and is applicable for air laying cable wire.
The above max. current is the carrying capacity at ambient temperature 25C;
If the unit is installed outdoors, use a UV resistant cable.
The above specification is for reference only. For specific wire and breaker models please check the corresponding
factory standard and actual installation requirement

[e-mail]
1300 859 933
www.evoheat.com.au
Evo Ultra Manual
Page 15
7.3 Wiring Diagrams

[e-mail]
1300 859 933
www.evoheat.com.au
Evo Ultra Manual
Page 16

[e-mail]
1300 859 933
www.evoheat.com.au
Evo Ultra Manual
Page 17

[e-mail]
1300 859 933
www.evoheat.com.au
Evo Ultra Manual
Page 18
7.4 Automatic Water Filling Valve
When the automatic filled-water valve is installed, the arrowhead orientation of inlet water must accord with
the orientation of the valve.
Automatic filled-water has been adjusted in advance to 1.5ba.
If readjusting the pressure of inlet water, operate as follows:
• Open the Screw Cap ( C )
• If reducing the pressure of water supply, unscrew the pressure to adjust the screw (B)
• If increasing the pressure of water supply, screw down the pressure to adjust the screw (B)
When the system needs to be filled with water at first, rest the handle (A) of filled-water. Then the handle
(A) can return (close) when the system is full of water.
Automatic filled-water valve needs periodic cleaning. When you must close the tap, unscrew the plug (D),
remove the inside filter net. Reassemble after cleaning.
NOTE: There are two connections for water pressure meters in the central section of automatic filled-water,
where the water pressure meter can be connected directly, and display the set pressure. The screw cap (C)
must be tweaked after adjusting the filled-water pressure.
B
C
1/4 '
D
A
1/2'
P re ssu r e Rel ease Val ve
Water Ou
t
Water In

[e-mail]
1300 859 933
www.evoheat.com.au
Evo Ultra Manual
Page 19
8. Maintenance
DO I NEED TO GET MY UNIT
SERVICED?
It is recommended that you get your EvoHeat unit serviced once a year by your
local certified air conditioning or refrigeration technician. If your unit is located in a
coastal area, more frequent maintenance may be necessary. During the service,
they will check the operational pressures of the refrigeration system and give the
unit and fins a good clean to ensure maximum performance.
DO WE HAVE
RECOMMENDED SERVICE
AGENTS?
EvoHeat have a large database of recommended service agents. Please contact
EvoHeat tech support on 1300 859 933 for your local service agent details.
SHOULD I CHECK MY UNIT
REGULARLY?
We recommend you check your unit regularly to avoid potential issues and
damage to your heat pump.
WHAT SHOULD I BE
CHECKING REGULARLY?
Check the water inlet/outlets often for leaks. You should avoid the condition of no
water or air entering into the system, as this will influence unit’s performance and
reliability.
You should clear the pool/spa filter regularly to avoid damage to the unit as a
result of the dirty of clogged filter.
The area around the unit should be dry, clean and well ventilated. Make sure
there is nothing blocking the airflow of the heater e.g. Leaf litter.
Discharge all water in the water pump and water system, so that freezing of the
water in the pump or water system does not occur. You should discharge the
water at the bottom of water pump if the unit will not be used for an extended
period. You should check the unit thoroughly and fill the system with water fully
before using it for the first time after a period of time.
Check the power supply and cable connection often, should the unit begin to
operate abnormally, switch it off and contact the qualified technician