Excelitas Technologies OmniCure SC Series Installation and operating manual

OmniCure®
SC0750/SC1000/SC2000/SC3000
UV Curing Solutions
Applicable for the following System Controller models:
Model Part Numbers
SC0750 019-00199R
SC1000 019-00186R
SC2000 019-00211R
SC3000 019-00213R
Installation/Reference Guide
Excelitas Canada Inc.
2260 Argentia Road
Mississauga (ON)
L5N 6H7 Canada
+1 905.821.2600
www.excelitas.com
035-00539R rev.5

OmniCure® SC- Series
UV Curing Solutions
www.excelitas.com/omnicure
Excelitas Canada Inc. 2021
All rights reserved
035-xxxxxR, rev.1
035-00539R rev 2
035-xxxxxR, rev.1
ii
035-00539R rev 5
Installation/Reference Guide
035-00539R
Excelitas Canada Inc. 2021
All rights reserved
No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system or
translated into any language in and form by any means without the prior written consent of Excelitas Canada
Inc. every effort has been made to ensure information in this manual is accurate, however, information in this
manual is subject to change without notice and does not represent a commitment on the part of the authors.
Trademarks:
OmniCure® is a trademark of Excelitas Canada Inc. All rights reserved. All other product names are
trademarks of their respective owners. All product or software photos shown are for reference only and are
subjected to change without notice.
Made in Canada. Doc. No. 035-00539R

OmniCure® SC- Series
UV Curing Solutions
www.excelitas.com/omnicure
Excelitas Canada Inc. 2021
All rights reserved
035-xxxxxR, rev.1
035-00539R rev 2
035-xxxxxR, rev.1
iii
035-00539R rev 5
Revision History
Revision # Comments
Rev 1.0 Initial release
Rev 2.0 Updated corporate logo, minor edits/corrections
Rev 3.0 Added SC2000 and SC3000
Rev 4.0 Streamlined regulatory section
Rev 5.0 Update to regulatory section and website links

OmniCure® SC- Series
UV Curing Solutions
www.excelitas.com/omnicure
Excelitas Canada Inc. 2021
All rights reserved
035-xxxxxR, rev.1
035-00539R rev 2
035-xxxxxR, rev.1
iv
035-00539R rev 5
Table Of Contents
1 Introduction ......................................................................................................................... 1
2 Safety Precautions/ User Warnings ........................................................................................ 2
2.1 Glossary of Symbols: ............................................................................................................................... 2
3 Getting Started .................................................................................................................... 3
3.1 Packaging Contents ................................................................................................................................ 3
4 Connecting the System Controller ......................................................................................... 4
5 Mounting the System Controller ............................................................................................ 6
5.1 Mechanical Dimensions ........................................................................................................................... 7
5.2 Electrical Connectivity ............................................................................................................................. 8
6 Troubleshooting ................................................................................................................... 9
7 Care and Maintenance ......................................................................................................... 11
8 Technical Specifications ...................................................................................................... 12
8.1 Environmental and Unit Specifications .................................................................................................. 12
8.2 Regulatory Compliance ......................................................................................................................... 12
8.3 China RoHS ........................................................................................................................................... 13
8.4 WEEE Directive (2012/19/EU) ................................................................................................................ 13
9 Warranty ............................................................................................................................ 15
9.1 Returning your System Controller to Excelitas Technologies for Service ................................................ 15
10 Contact Information ........................................................................................................... 16
Figures
Figure 1 SC0750/SC1000/SC2000 Unit ....................................................................................................................... 4
Figure 2 SC3000 Unit ................................................................................................................................................. 4
Figure 3 SC0750/SC1000/SC2000 Mechanical Dimensions ......................................................................................... 7
Figure 4 SC3000 Mechanical Dimensions ................................................................................................................... 7
Figure 5 Power Connector (looking at System Controller) .......................................................................................... 8
Tables
Table 1 Power Connector Pin Out .............................................................................................................................. 8
Table 2 Technical Specifications .............................................................................................................................. 12

OmniCure® SC- Series
UV Curing Solutions
www.excelitas.com/omnicure
Excelitas Canada Inc. 2021
All rights reserved
035-xxxxxR, rev.1
035-00539R rev 2
035-xxxxxR, rev.1
1
035-00539R rev 5
1 Introduction
The OmniCure ® SC0750/SC1000/SC2000/SC3000 System Controllers are designed to be used specifically
with OmniCure ® AC-Series UV LED systems. Designed to fit in a 1U rack, these System Controllers provide a
compact solution for powering up to two AC-series products simultaneously. Operating over a universal input
AC voltage range from a standard receptacle allows easy and quick installation without the need for
dedicated electrical resources. The rear-mounted integrated electrical circuit breaker provides electrical fault
protection and isolation while a front-mounted on/off switch and power indicator provides users with a
simple, easy-to-access means of powering AC-series products on a day-to-day basis.
OmniCure® has combined next generation optical engineering, state-of-the art electronics and fibre-optics
to produce sophisticated technologies that employ light. Today, OmniCure® is a leading developer of light-
based systems for sectors ranging from manufacturing to bio-medical, and is unmatched in itscommitment
to quality and service.
This manual covers the following models:
SC0750 019-00199R
SC1000 019-00186R
SC2000 019-00211R
SC3000 019-00213R
Excelitas Technologies recommends reading this guide to discover all features of the OmniCure®
SC0750/SC1000/SC2000/SC3000 System Controllers, and how to use them.

OmniCure® SC- Series
UV Curing Solutions
www.excelitas.com/omnicure
Excelitas Canada Inc. 2021
All rights reserved
035-xxxxxR, rev.1
035-00539R rev 2
035-xxxxxR, rev.1
2
035-00539R rev 5
2 Safety Precautions/ User Warnings
NOTE: The SC Series PSU have been designed for safe use, however, if the equipment is used in a manner not
specified by the manufacturer, the protection systems provided by the equipment may be impaired.
The safety of any system incorporating an SC Series PSU is the responsibility of the assembler of the system
2.1 Glossary of Symbols:
Caution risk of danger – consult accompanying documents.
Protective Conductor Terminal
Earth (Ground) Terminal
CAUTION, Risk of Electrical Shock

OmniCure® SC- Series
UV Curing Solutions
www.excelitas.com/omnicure
Excelitas Canada Inc. 2021
All rights reserved
035-xxxxxR, rev.1
035-00539R rev 2
035-xxxxxR, rev.1
3
035-00539R rev 5
3 Getting Started
3.1 Packaging Contents
The package contains:
 One of the following System Controllers:
 SC0750 019-00199R
 SC1000 019-00186R
 SC2000 019-00211R
 SC3000 019-00213R
 AC power cable, selected for mains power receptacles in the destination country
 A small polythene bag containing mounting brackets (x2)
 Documentation CD
 Depending on the exact order, the package may also contain a DC power cable.
Carefully remove the contents and store the packaging materials for future use.
In addition to the System Controller enclosed, a functional UV curing setup will require:
 At least 1 DC power cable (for example, 018-00559R or 018-00595R – 5m power cable)
 At least 1 AC-series UV LED Head.
Before installation, ensure that the total DC electrical load does not exceed
approximately 85% of the rating of the SC-series unit to be installed.

OmniCure® SC- Series
UV Curing Solutions
www.excelitas.com/omnicure
Excelitas Canada Inc. 2021
All rights reserved
035-xxxxxR, rev.1
035-00539R rev 2
035-xxxxxR, rev.1
4
035-00539R rev 5
4 Connecting the System Controller
Figure 1 SC0750/SC1000/SC2000 Unit
Figure 2 SC3000 Unit
1. Before any electrical connections are made, ensure that the electrical circuit breaker is tripped. This can
be done by pushing the breaker switch away from the AC-inlet receptacle.
2. Ensure that the power switch on the front of the System Controller is set to the “off” position.
3. Locate the AC power cord and insert into the AC-inlet receptacle on the rear of the System Controller.
4. Locate the pair of 5W5 DC power connectors on the rear of the System Controller. Connect the DC
cable and tighten the jack screws to prevent the connector disengaging during use.
5. Connect the other end of the cable to the UV LED head and tighten the jack screws as before.
6. Connect any other control cabling to the UV LED head as required and as per the specific product
manual for that system.
Power Switch
Status Indicator
Front View
Rear View
Breaker Switch AC Inlet Receptacle
DC Power
Connectors
Rear View
DC Power
Connectors
AC Inlet R
eceptacle
Breaker Switch

OmniCure® SC- Series
UV Curing Solutions
www.excelitas.com/omnicure
Excelitas Canada Inc. 2021
All rights reserved
035-xxxxxR, rev.1
035-00539R rev 2
035-xxxxxR, rev.1
5
035-00539R rev 5
7. If the System Controller is intended to power more than one UV LED head, repeat steps 5and 6 for each
unit to be connected.
8. Plug the trailing end of the AC power cord into an AC mains outlet at the wall capable of supplying
voltage and current as per the specifications in this manual.
9. Arm the circuit breaker by pushing the breaker switch towards the AC-inlet receptacle.
10. Using the power switch on the front of the System Controller, power on the connected AC-series UV
LED equipment. When the outputs are live, a green LED status indicator on the front of the System
Controller will be lit. The internal power supply circuitry is now energized and the internal fan should
now be audible.
11. If the status indicator does not illuminate and the UV LED heads fail to power up, ensure that steps 1-9
have been followed properly.
**WARNING**
The System Controller should only be connected to a mains outlet using the style and rating of
cable provided. This regional cable is of the 3-pin variety and carries a protective earth
connection. For user safety, do not substitute this cable with any 2-pin variety.

OmniCure® SC- Series
UV Curing Solutions
www.excelitas.com/omnicure
Excelitas Canada Inc. 2021
All rights reserved
035-xxxxxR, rev.1
035-00539R rev 2
035-xxxxxR, rev.1
6
035-00539R rev 5
5 Mounting the System Controller
The SC0750, SC1000 and SC2000 share the same mechanical chassis, while the SC3000 has a slightly larger
mechanical enclosure. However, the mounting instructions apply equally to all models with the exception of
mounting hole locations.
It is recommended that the System Controller be carried by holding the unit on two opposite sides, with
fingers supporting the underside of the unit. During installation, the unit is light enough to be balanced in one
hand, leaving the other hand free for inserting mounting screws. If access is restricted or the installer prefers
a different approach, supporting the underside of the unit at approximately the level height of the installation
location using a suitable mechanical prop would also suffice.
While the System Controller can be left as a free-standing unit, it is intended to be easily installed in well-
ventilated 19” rack-mounting. It is recommended that the System Controller be installed with the text on the
labels oriented the right way up.
To install the System Controller in a 19” rack:
1. Disconnect any electrical cables that are connected to the main chassis.
2. Remove the two mounting brackets from the polythene bag.
3. Locate the four screws on the sides of the enclosure towards the front and remove.
4. The mounting bracket has two slots and two holes. The holes are intended for attachment of the
brackets to the main chassis. Using two of the removed screws, attach the mounting bracket to the side
of the enclosure.
5. Using the two remaining screws, repeat step 4 for the other side of the enclosure. The enclosure is now
ready to be mounted in the rack.
6. Identify a screw-hole pair in the rack that lines up with the holes in the mounting brackets and using a
screw-type compatible with the rack threading (usually #10-32 (imperial) or M4 (metric)), thread a
single screw into one of the two holes and tighten by hand.
7. Supporting the foremost underside of the unit, move to the other side of the chassis and level the front
of the enclosure. Insert another screw into one of the two holes and tighten by hand.
8. Move the support to the rear of the enclosure and raise the support until the front-back direction is
level. Insert an additional screw into the mounting bracket on each side. The unit should now be in
approximately the final intended lateral position.
9. Adjust the position of the unit (if necessary) to finalize location. The mounting bracket face that mates
with the rack is slotted to allow some adjustment.
10. When satisfied with the position, tighten the four mounting screws using a screwdriver. Do not over-
tighten as this may strip the threading in the rack and render the mounting location useless.
Note: The mounting brackets are designed to support the mechanical load of the System Controller chassis
only. They are not designed to support any additional weight placed onto the top of the unit. Placing
additional mechanical loading onto the unit may damage the mounting brackets, the racking or the
mounting screws themselves. Excelitas Technologies considers evidence of such cases as outside of
warranty.
It is recommended that both AC and DC-side cabling be tied off and mechanically supported to prevent
undue stress on the electrical connectors.
Warning: This device includes a circuit breaker located on the rear panel, do not position the
equipment so that it is difficult to operate the disconnecting device

OmniCure® SC- Series
UV Curing Solutions
www.excelitas.com/omnicure
Excelitas Canada Inc. 2021
All rights reserved
035-xxxxxR, rev.1
035-00539R rev 2
035-xxxxxR, rev.1
7
035-00539R rev 5
5.1 Mechanical Dimensions
Figure 3 SC0750/SC1000/SC2000 Mechanical Dimensions
Figure 4 SC3000 Mechanical Dimensions

OmniCure® SC- Series
UV Curing Solutions
www.excelitas.com/omnicure
Excelitas Canada Inc. 2021
All rights reserved
035-xxxxxR, rev.1
035-00539R rev 2
035-xxxxxR, rev.1
8
035-00539R rev 5
5.2 Electrical Connectivity
DC Power Connectors (x2)
Figure 5 Power Connector (looking at System Controller)
PIN Name Description
A1 +ve 48V DC power feed.
A2 +ve 48V DC power feed. (SC2000 & SC3000 only. Shared current through this pin)
A3 -ve 48V DC power return.
A4 -ve 48V DC power return. (SC2000 & SC3000 only. Shared current through this pin)
A5 Chassis Chassis ground connection
Table 1 Power Connector Pin Out
AC Power Connectors
SC0750/SC1000
SC2000/SC3000

OmniCure® SC- Series
UV Curing Solutions
www.excelitas.com/omnicure
Excelitas Canada Inc. 2021
All rights reserved
035-xxxxxR, rev.1
035-00539R rev 2
035-xxxxxR, rev.1
9
035-00539R rev 5
6 Troubleshooting
Service to be completed by qualified Excelitas Technologies personnel only!
If the green LED indicator fails to illuminate:
 Validate that main voltage is reaching the receptacle intended for use by powering an independent
electrical load from it, (e.g. a light).
 Check that the AC mains cable is connected securely to the AC mains and AC inlet receptacle on the
SC-series unit.
 Ensure that the circuit breaker is set to the “armed” position.
 Ensure that the front panel on/off switch is set to the on position.
 If the indicator LED remains unlit, try disconnecting the DC-side cables and repeating steps 1-4. This
will isolate the fault, if any, to the supply or the downstream connectivity.
If the UV LED heads are running and then power appears to be disconnected from them:
 Ensure that the combined electrical load from the connected AC-series heads is a supported
configuration for the System Controller employed.
 Ensure that there is adequate ventilation for air intake and exhaust. If the System Controller is
installed in a cabinet, the ambient temperature must be less than 40 degrees Celsius.
If the UV LED heads appear to be running at a reduced intensity:
 Verify that the AC mains voltage for the SC0750 and SC1000 is within the range of 100-240V AC
@50/60Hz. Of particular concern is the low end AC voltage.
 Verify that the AC mains voltage for the SC2000 and SC3000 is within the range of 200-240V AC
@50/60Hz. Of particular concern is the low end AC voltage.
Caution: Inspect the AC cable for any signs of wear or mechanical damage. If any point along the cable
looks damaged, contact Excelitas Technologies Service department for replacement (refer to Section 0,
“Please make a note of the problem encountered, the steps followed to isolate the problem and the result of
any trouble shooting steps taken.
Telephone the nearest Excelitas Technologies Service Centre to obtain a Return Authorization Number so
that repairs may be completed quickly and efficiently. In North America, request for Return Authorization
number can be made online at https://www.excelitas.com/ox_service_request_form
Enclose details of the problem with the unit and return both to the Excelitas Technologies Service Centre.
The unit should be returned in its original packaging if possible.
Include a phone number and contact person who may be reached for any additional service-related
questions.
Contact Information”).
 Verify that the DC voltage at the point of load is greater than 47V.
Caution: Inspect the DC cable(s) for any signs of wear or mechanical damage. If any point along the
cable looks damaged, contact Excelitas Technologies Service department for
replacement.

OmniCure® SC- Series
UV Curing Solutions
www.excelitas.com/omnicure
Excelitas Canada Inc. 2021
All rights reserved
035-xxxxxR, rev.1
035-00539R rev 2
035-xxxxxR, rev.1
10
035-00539R rev 5
Caution: It is normal for electrical cables and connectors to warm up while in use. If a cable or
connector is too hot to be comfortably handled, there may be an electrical problem
associated with it. Contact Excelitas Technologies Service department for guidance.

OmniCure® SC- Series
UV Curing Solutions
www.excelitas.com/omnicure
Excelitas Canada Inc. 2021
All rights reserved
035-xxxxxR, rev.1
035-00539R rev 2
035-xxxxxR, rev.1
11
035-00539R rev 5
7 Care and Maintenance
The System Controllers are designed to provide years of trouble-free operation with little maintenance
activity. Here are some guidelines for ensuring long-life from the System Controller.
 Do not locate the System Controller directly in an environment with air-borne contamination. If the
unit needs to be in such an environment, install inside a ventilated cabinet with fan-assisted air-
filtration. Observe the air flow direction of the SC-series (left to right) relative to the cabinet and
configure the cabinet accordingly.
 Ensure all air-intakes and exhaust vents are at least 50mm away from obstruction and free from dust
and debris. If necessary, wipe with a dry cloth or use compressed air to dislocate particulate matter
which may be stuck to the vents.
Caution: Do not use a wet cloth or any aerosol-type cleaning fluids as this may be ingested by the
unit, causing damage and the risk of electrical shock.
 If the unit needs to be cleaned more thoroughly, first disconnect from the AC mains. Using a damp
cloth (impregnated with either with water or alcohol), wipe the surfaces of the unit. Take care to
ensure that the cloth is not dripping. If using alcohol, avoid the labels to prevent them from being
smeared or detaching from the unit and avoid heavy rubbing. Do not use acetone.
 Ensure that AC-side and DC-side cables are connected firmly to the chassis and (where possible)
screwed in to prevent damage to the connectors. Cables should be tied off to provide strain relief to
the electrical connectors.
 Do not use the electrical breaker as the means to turn on/off power on a regular basis. The switch on
the front of the unit is designed for more on-off cycles. The breaker should be set once when the
system is commissioned and only reset if it trips at a later date.

OmniCure® SC- Series
UV Curing Solutions
www.excelitas.com/omnicure
Excelitas Canada Inc. 2021
All rights reserved
035-xxxxxR, rev.1
035-00539R rev 2
035-xxxxxR, rev.1
12
035-00539R rev 5
8 Technical Specifications
8.1 Environmental and Unit Specifications
SC0750 SC1000 SC2000 SC3000
Operating Temperature Range (degrees
C)
10-40C
Relative Humidity 10-80% (non-condensing)
Dimensions (mm)
(not including mounting
brackets)
Length 341
Depth 445
Height 44 67
Weight (kg) 3.9kg (8.61 lbs) 4.22kg (9.3 lbs) 6.5kg (14.3 lbs)
Input Voltage 100-240V AC 50/60Hz 200-240 AC
50/60Hz
200-220 AC
50/60Hz
220-240 AC
50/60Hz
Maximum AC input current (A) 9-4.3 12-6.5 13-9.6 15.6-13
Circuit Breaker Rating 10 13 16A
Maximum DC power (W) 750 1000 1992 2400 2700
DC output voltage 48V, +/-1V
Maximum DC current (A) 15.7 21 41.5 50 56.3
Number of DC output connectors 2 4
Certifications CE, RoHS, WEEE
Table 2 Technical Specifications
8.2 Regulatory Compliance
The SC0750/SC1000/SC2000/SC3000 System Controllers have been tested and found to comply with product
safety and electromagnetic compatibility requirements. For a complete list of tests and for certification
details, please contact your OmniCure® representative or visit www.excelitas.com/omnicure for more
details.
**WARNING**
Changes or modifications not expressly approved by Excelitas Technologies could
void the user’s authority to operate the equipment.
Product Safety:
General Requirements
IEC Equipment Class: I
Installation Category: II
Pollution Degree: 2
Requirements for MAINS cords or cord sets are contained in ANSI/UL 817 and CSA C22.2 No. 21.
Requirements for general use receptacles, attachment plugs, and similar wiring devices are contained in
ANSI/UL 498 and CSA C22.2 No. 42, CSA C22.2 No. 182.1, CSA C22.2 No. 182.2, and CSA C22.2 No. 182.3.
For Canadian and United States standards for MAINS connectors:

OmniCure® SC- Series
UV Curing Solutions
www.excelitas.com/omnicure
Excelitas Canada Inc. 2021
All rights reserved
035-xxxxxR, rev.1
035-00539R rev 2
035-xxxxxR, rev.1
13
035-00539R rev 5
Requirements for plugs of MAINS cords are contained in ANSI/UL 498 and CSA C22.2 No. 42, CSA C22.2 No.
182.1, CSA C22.2 No. 82.2, and CSA C22.2 No. 182.3.
CE Marking:
Council Directive 2014/35/EU Low Voltage
Council Directive 2014/30/EC EMC
Council Directive 2012/19/EU WEEE
Council Directive 2011/65/EU
as amended by (EU) 2015/863
RoHS
This is a class A product. In a domestic environment, this product may cause radio interference
in which case the user may be required to take adequate measures.
FCC Class A Digital Device or Peripheral - Information to User
Note: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial environment. This equipment generates, uses,
and can radiate radio frequency energy and, if not installed and used in accordance with the instruction
manual, may cause harmful interference to radio communications. Operation of this equipment in a
residential area is likely to cause harmful interference in which case the user will be required to correct the
interference at their own expense.
**WARNING**
Changes or modifications not expressly approved by Excelitas Technologies could
void the user’s authority to operate the equipment.
8.3 China RoHS
The symbol above indicates a product does not contain any restricted substances.
8.4 WEEE Directive (2012/19/EU)
The symbol above indicates that this product should not be disposed of along with municipal waste, that the
product should be collected separately, and that a separate collection system exists for all products that
contain this symbol within member states of the European Union.

OmniCure® SC- Series
UV Curing Solutions
www.excelitas.com/omnicure
Excelitas Canada Inc. 2021
All rights reserved
035-xxxxxR, rev.1
035-00539R rev 2
035-xxxxxR, rev.1
14
035-00539R rev 5
The equipment that you bought has required the extraction and use of natural resources for its production. It
may contain hazardous substances that could impact health and the environment.
In order to avoid the dissemination of those substances in our environment and to diminish the pressure on
the natural resources, we encourage you to use the appropriate take-back systems. Those systems will reuse
or recycle most of the materials of your end life equipment in a sound way.
The crossed-out wheeled bin symbol indicated above invites you to use those systems.
If you need more information on the collection, reuse and recycling systems, please contact your local or
regional waste administration.

OmniCure® SC- Series
UV Curing Solutions
www.excelitas.com/omnicure
Excelitas Canada Inc. 2021
All rights reserved
035-xxxxxR, rev.1
035-00539R rev 2
035-xxxxxR, rev.1
15
035-00539R rev 5
9 Warranty
Excelitas Technologies warrants the original purchaser for a period of one (1) full year, calculated from the
date of purchase, that the equipment sold is free from defects in material and workmanship.
In the event of a claim under this warranty, the equipment is to be sent postage and carriage paid to the
Excelitas Technologies Service Centre. Returned equipment will not be received without a Return
Authorization (RA) Number, issued by the appropriate Service Centre.
In order for us to serve you better, include a written description of the fault and the name and telephone
number of a contact person who may be contacted for additional service related questions.
Any claims for units received with defects in material or workmanship must be reported to an authorized
Excelitas Technologies Service Centre within 30 days from the original date of receipt and returned within 30
days of reporting to a an authorized Excelitas Technologies Service Centre. Excelitas Technologies will repair
or replace these reported defects free of charge. The equipment must be sent postage and carriage paid.
Package the equipment in its original shipping case or as appropriate to prevent damage during transport.
In the case of damage caused by wear and tear, careless handling, neglect, by the use of force or in the case
of interventions and repairs not carried out by an Excelitas Technologies Authorized Service Centre, the
warranty ceases to be valid. This warranty may not form the basis for any claims for damages, in particular
not for compensation of consequential damages.
This warranty is not transferable.
9.1 Returning your System Controller to Excelitas Technologies for Service
Please make a note of the problem encountered, the steps followed to isolate the problem and the result of
any trouble shooting steps taken.
Telephone the nearest Excelitas Technologies Service Centre to obtain a Return Authorization Number so
that repairs may be completed quickly and efficiently. In North America, request for Return Authorization
number can be made online at https://www.excelitas.com/ox_service_request_form
Enclose details of the problem with the unit and return both to the Excelitas Technologies Service Centre.
The unit should be returned in its original packaging if possible.
Include a phone number and contact person who may be reached for any additional service-related
questions.

OmniCure® SC- Series
UV Curing Solutions
www.excelitas.com/omnicure
Excelitas Canada Inc. 2021
All rights reserved
035-xxxxxR, rev.1
035-00539R rev 2
035-xxxxxR, rev.1
16
035-00539R rev 5
10 Contact Information
Excelitas Canada Inc.
2260 Argentia Road
Mississauga, Ontario
L5N 6H7 CANADA
Tel.: [phone]
Toll: [phone] (USA and Canada)
Fax: [phone]
http://www.excelitas.com/Pages/Product/OmniCure.aspx
www.excelitas.com/omnicure
Technical Assistance:
[email protected]
https://www.excelitas.com/ox_service_request_form
For a complete listing of Authorized OmniCure Distributors and Service Centres please go to
https://www.excelitas.com/dealer-search