EXO2 HEATWAVE User manual

HEATWAVE
Heated back support/belt
The Heat Inside®
The Heat Inside®
www.exo2.co.uk
TROUBLESHOOTING
What happens if my HeatWave belt doesn’t get warm?
Firstly, check that you have the HeatWave belt connected
to a power source.
Ensure the portable power pack is charged. This can be
done by firstly plugging the power pack into the associated
charger. If the red light on the charger comes on and stays
on, the power pack needs to be charged. If the power pack
is charged, check that the belt plug is correctly attached to
the powerpack.
Should you have any questions about your heated products,
please contact:
Customer Services Dept
EXO2
Caledonian House
Phoenix Crescent
Strathclyde Business Park
Bellshill ML4 3NJ
Tel: [phone]
Email: [email protected]
SAFETY FEATURES
The FabRoc® heating system has been designed for safe
and reliable use. It has been tested to comply with
European safety regulations and the power system has been
CE marked. Safety devices are included to ensure the unit
is rendered safe, even under fault conditions.
DO NOT replace or interfere with the electrical components
in your belt or the power pack and charger unit.
The HeatWave belt, including portable power pack, is not
designed to be used under water. In addition, the portable
power pack must not, under any circumstances, be
immersed in water as this can cause electrical faults.
CLEANING INSTRUCTIONS
Remove power pack
Hand wash in warm water
Use non-biological soap powder
Rinse thoroughly
DO NOT TUMBLE DRY OR DRY CLEAN
WARRANTY
Every EXO2 garment is supplied with a one-year warranty
covering all electronic and mechanical failures. In the
unlikely event that any part should fail within the first year,
return it to us and we will repair or replace it free of charge.
Note: the warranty does not cover intentional alterations,
accidental damage or improper cleaning.
The Heat Inside®
The Heat Inside®

Your high performance HeatWave support belt has
been designed to provide you with warmth and support
where and when you need it, whatever the weather.
Our unique heating system uses FabRoc®, a
revolutionary polymer that is extremely efficient in
generating heat from a low voltage power pack.
FabRoc® panels are sewn into the garment to
provide direct heat to your body in certain key areas.
FabRoc® is scientifically proven to be therapeutically
beneficial, with no wires or hotspots, it transfers
warmth through your body via the bloodstream.
The FabRoc® panels are pre-set to a maximum surface
temperature of 500C. It is not possible to ‘overheat’
FabRoc® as it automatically uses less power as it
reaches its operating temperature, a unique property
that ensures the material is very safe.
The support belt also features polycarbonated strips
and vented elastic panels that provide flexible and
adjustable support where and when you need it most.
GETTING THE BEST RESULTS
The closer the FabRoc® panels are to your skin, the more
heat you will feel, so you can create your own microclimate
wearing only a fine pullover, t-shirt or blouse underneath.
The portable power pack will provide heat on the lower
back area for up to 3 hours of continuous use at full
power. Experience suggests that you will get the best
from your HeatWave by turning the battery up and down
as described below.
Normally you would switch your belt on a few minutes
before wearing it. You should then be able to turn the
temperature down once it’s reached a comfortable level,
as the heat generated from your muscles will be sufficient
to keep you warm.
If you are resting, or the ambient temperature drops and
you feel cold, you can then increase the power indicator
and modulate as required to maintain your ideal comfort
level.
The Heat Inside®
www.exo2.co.uk
USING THE POWER PACK
Fully charge your power pack before initial use, this will
take approximately 3 hours.
1. Remove connected cable from pocket.
2. Insert the small 1.3mm DC plug into the power pack.
3. See label on power pack for user operating instructions.
CHARGING THE POWER PACK
1. Remove power pack from the belt.
2. Connect charger unit to power pack.
The red light on the front of the charger
will light up when the charger is
checking on the level of battery power.
Fully depleted power packs will take
approximately 3 hours to fully recharge.
The red light stays on continuously while the power pack
is being charged. The red light turns to green when fully
charged.
The charger supplied has been chosen specifically for the
power pack supplied. No other charger must be used.