Extreme Networks ExtremeWireless NX-7500 Series User manual

NX-7500 Series Integrated
Services Platform
Installation Guide
9035183
Published February 2018

Copyright © 2018 Extreme Networks, Inc. All rights reserved.
Legal Notice
Extreme Networks, Inc. reserves the right to make changes in specifications and other information
contained in this document and its website without prior notice. The reader should in all cases
consult representatives of Extreme Networks to determine whether any such changes have been
made.
The hardware, firmware, software or any specifications described or referred to in this document
are subject to change without notice.
Trademarks
Extreme Networks and the Extreme Networks logo are trademarks or registered trademarks of
Extreme Networks, Inc. in the United States and/or other countries.
All other names (including any product names) mentioned in this document are the property of
their respective owners and may be trademarks or registered trademarks of their respective
companies/owners.
For additional information on Extreme Networks trademarks, please see:
www.extremenetworks.com/company/legal/trademarks
Software Licensing
Some software files have been licensed under certain open source or third-party licenses. End-
user license agreements and open source declarations can be found at:
www.extremenetworks.com/support/policies/software-licensing
Support
For product support, phone the Global Technical Assistance Center (GTAC) at 1-800-998-2408
(toll-free in U.S. and Canada) or [phone]. For the support phone number in other
countries, visit: http://www.extremenetworks.com/support/contact/
For product documentation online, visit: https://www.extremenetworks.com/documentation/

Table of Contents
Preface.........................................................................................................................................4
Text Conventions...................................................................................................................................................................4
Platform-Dependent Conventions................................................................................................................................4
Providing Feedback to Us.................................................................................................................................................5
Getting Help.............................................................................................................................................................................5
Extreme Networks Documentation............................................................................................................................. 6
Chapter 1: Overview...................................................................................................................7
Package Contents.................................................................................................................................................................7
Accessories...............................................................................................................................................................................7
Power Supplies.......................................................................................................................................................................8
Power Supply Status LEDs...............................................................................................................................................8
Power Protection...................................................................................................................................................................8
Chapter 2: Hardware Installation.............................................................................................9
Warnings..................................................................................................................................................................................10
Cautionary Statements.....................................................................................................................................................10
Site Preparation..................................................................................................................................................................... 11
Safety Instructions for Rack Mount Installations...................................................................................................11
Installing the NX-7500 Series Integrated Services Platform..........................................................................12
NX-7500 Series Integrated Services Platform Power Supply Installation............................................... 12
NX-7500 Series Integrated Services Platform NMC Installation.................................................................. 13
NX-7500 Series Integrated Services Platform SFP Installation....................................................................14
NX-7530 Integrated Services Platform Disc Drive Assembly Replacement...........................................15
NX-7510/NX-7520/NX-7530 Series Slide Rail Kit Installation Instructions.............................................16
Chapter 3: NX-7500 Series Specifications.......................................................................... 20
Chapter 4: Regulatory Information........................................................................................21
Radio Frequency Interference Requirements - FCC.......................................................................................... 21
Radio Frequency Interference Requirements - Canada................................................................................... 21
CE Marking and European Area (EEA)....................................................................................................................22
Statement of Compliance...............................................................................................................................................22
Japan (VCCI) - Voluntary Control Council for Interference Class A ITE..................................................22
Korea Warning Statement for Class A ITE............................................................................................................. 22
Chinese Warning Statement for Class A ITE.........................................................................................................22
Waste Electrical and Electronic Equipment.......................................................................................................... 22
Turkish WEEE Statement of Compliance............................................................................................................... 23
End-User Software License Agreement.................................................................................................................. 23
China RoHS Compliance................................................................................................................................................. 29
NX-7500 Series Integrated Services Platform 3

Preface
Text Conventions
The following tables list text conventions that are used throughout this guide.
Table 1: Notice Icons
Icon Notice Type Alerts you to...
General Notice Helpful tips and notices for using the product.
Note Important features or instructions.
Caution Risk of personal injury, system damage, or loss of data.
Warning Risk of severe personal injury.
New This command or section is new for this release.
Table 2: Text Conventions
Convention Description
Screen displays This typeface indicates command syntax, or represents information as it appears on the
screen.
The words enter and
type
When you see the word “enter” in this guide, you must type something, and then press
the Return or Enter key. Do not press the Return or Enter key when an instruction
simply says “type.”
[Key] names Key names are written with brackets, such as [Return] or [Esc]. If you must press two
or more keys simultaneously, the key names are linked with a plus sign (+). Example:
Press [Ctrl]+[Alt]+[Del]
Words in italicized type Italics emphasize a point or denote new terms at the place where they are defined in
the text. Italics are also used when referring to publication titles.
Platform-Dependent Conventions
Unless otherwise noted, all information applies to all platforms supported by ExtremeXOS®software,
which are the following:
•ExtremeSwitching®switches
•Summit®switches
•SummitStack™
NX-7500 Series Integrated Services Platform 4

When a feature or feature implementation applies to specific platforms, the specific platform is noted in
the heading for the section describing that implementation in the ExtremeXOS command
documentation (see the Extreme Documentation page at http://
documentation.extremenetworks.com). In many cases, although the command is available on all
platforms, each platform uses specific keywords. These keywords specific to each platform are shown in
the Syntax Description and discussed in the Usage Guidelines sections.
Providing Feedback to Us
We are always striving to improve our documentation and help you work better, so we want to hear
from you! We welcome all feedback but especially want to know about:
•Content errors or confusing or conflicting information.
•Ideas for improvements to our documentation so you can find the information you need faster.
•Broken links or usability issues.
If you would like to provide feedback to the Extreme Networks Information Development team about
this document, please contact us using our short online feedback form. You can also email us directly at
[e-mail].
Getting Help
If you require assistance, contact Extreme Networks using one of the following methods:
•GTAC (Global Technical Assistance Center) for Immediate Support
•Phone: [phone] (toll-free in U.S. and Canada) or [phone]. For the support
phone number in your country, visit: www.extremenetworks.com/support/contact
•Email: [e-mail]. To expedite your message, enter the product name or
model number in the subject line.
•Extreme Portal — Search the GTAC knowledgebase, manage support cases and service contracts,
download software, and obtain product licensing, training, and certifications.
•The Hub — A forum for Extreme customers to connect with one another, answer questions, and
share ideas and feedback. This community is monitored by Extreme Networks employees, but is not
intended to replace specific guidance from GTAC.
Before contacting Extreme Networks for technical support, have the following information ready:
•Your Extreme Networks service contract number and/or serial numbers for all involved Extreme
Networks products
•A description of the failure
•A description of any action(s) already taken to resolve the problem
•A description of your network environment (such as layout, cable type, other relevant environmental
information)
•Network load at the time of trouble (if known)
•The device history (for example, if you have returned the device before, or if this is a recurring
problem)
•Any related RMA (Return Material Authorization) numbers
Preface
NX-7500 Series Integrated Services Platform 5

Extreme Networks Documentation
To find Extreme Networks product guides, visit our documentation pages at:
Current Product Documentation www.extremenetworks.com/documentation/
Archived Documentation (for earlier
versions and legacy products)
www.extremenetworks.com/support/documentation-archives/
Release Notes www.extremenetworks.com/support/release-notes
Open Source Declarations
Some software files have been licensed under certain open source licenses. More information is
available at: www.extremenetworks.com/support/policies/software-licensing.
Preface
NX-7500 Series Integrated Services Platform 6

1Overview
Package Contents
Accessories
Power Supplies
Power Supply Status LEDs
Power Protection
The NX-7500 Series Integrated Services Platform lets you centrally administer networks of up to 2,048
WLAN Access Points geographically dispersed over small or medium sized enterprise locations. WiNG
Access Points intelligently handle the trac flows, quality of service and security at remotely distributed
locations, while the NX-7500 series integrated services platforms provide a single point for
configuration, policy setting, and remote troubleshooting.
Hotspot configuration, security policy management, and statistics aggregation are all done by one
integrated services platform. This ecient WLAN architecture makes controlling the network easier, and
reduces the hardware expense required to support large networks.
Package Contents
An NX-7500 series Integrated Services Platform ships with the following:
•NX-7500 series Integrated Services Platform
•Console cable
•Rack mount brackets
•NX-7510/NX-7520/NX-7530 Integrated Services Platform Installation Guide (this document)
Accessories
The following accessories are available for NX-7500 series Integrated Services Platform:
•2 port 10Gb Network Mezzanine Card (NMC) module for use with 10Gb SFP+ transceivers
•10GbPS short range 850nm multi-mode SFP+ transceiver for use with 10Gb NMC
•10GbPS long range 10km single-mode SFP+ transceiver for use with 10Gb NMC
•4 port 10Gb NMC Module for use with 1Gb SFP transceivers
•1GbPS short range SFP transceiver for use with 1Gb NMC
•1GbPS long range SFP transceiver for use with 1Gb NMC
•Spare AC power supply for NX-7510 or NX-7530
•Spare DC power supply for NX-7510 or NX-7530
•Mounting kit with sliding rails
•Spare 500GB hard drive for NX-7530
Additional Recommended Equipment:
•Standard, grounded 100-240 VAC 50/60 Hz connection
NX-7500 Series Integrated Services Platform 7

•Standard 19-inch 1U height equipment rack
•Depending on the power supply, an AC or DC Uninterruptible Power Supply (UPS) is recommended
Power Supplies
NX-7510 and NX-7530 integrated services platforms are initially configured with a single AC power
supply. An NX-7520 integrated services platform is initially configured with two DC power supplies.
Installation of an Uninterruptible Power Supply (UPS) is recommended if a second power supply is
installed in an NX-7510 or NX-7530. To replace a failed power supply or install a new power supply, see
NX-7500 Series Integrated Services Platform Power Supply Installation on page 12
Power Supply Status LEDs
Each NX-7500 AC or DC power supply module has a single bi-color LED to indicate power supply
status. The LED is visible on the rear panel of each installed power supply.
The LED functionality for the power supplies is listed in the following table:
State Description
O No power to all power supplies.
Flashing red No input power.
Flashing blue or green Power present. Only standby output on.
Blue or green Power supply on. Normal operation.
Red Power supply failure.
Flashing red/blue
or
Flashing red/green
Power supply warning. Reaching end or life or
exceeding limits.
Power Protection
•If possible, use a circuit dedicated to data processing equipment. Commercial electrical contractors
are familiar with wiring for data processing equipment and can help with the load balancing of these
circuits.
•Install surge protection. Be sure to use a surge protection device between the electricity source and
the NX-7500 series integrated services platform.
•Install an Uninterruptible Power Supply (UPS). A UPS provides continuous power during a power
outage. Some UPS devices have integral surge protection. UPS equipment requires periodic
maintenance to ensure reliability. A UPS of the proper capacity for the data processing equipment
must be purchased.
Overview
NX-7500 Series Integrated Services Platform 8

2Hardware Installation
Warnings
Cautionary Statements
Site Preparation
Safety Instructions for Rack Mount Installations
Installing the NX-7500 Series Integrated Services Platform
NX-7500 Series Integrated Services Platform Power Supply Installation
NX-7500 Series Integrated Services Platform NMC Installation
NX-7500 Series Integrated Services Platform SFP Installation
NX-7530 Integrated Services Platform Disc Drive Assembly Replacement
NX-7510/NX-7520/NX-7530 Series Slide Rail Kit Installation Instructions
The following sections describe the hardware installation for the NX-7500 series integrated services
platform.
The following figure represents the front of the NX-7510 and NX-7520 models:
The following figure represents the front of the NX-7530 model:
To prepare for the installation:
1 Match the model number on the purchase order with the model numbers in the packing list and on
the integrated services platform.
2 Verify the contents of the box include the intended NX-7500 series integrated services platform and
the included hardware matches the package contents.
NX-7500 Series Integrated Services Platform 9

Part Number Description
NX-7510-100R0-WR NX-7510 base server appliance with single AC power
supply
NX-7520-100R0-WR NX-7520 base server appliance with dual DC power
supply
NX-7530-100R0-WR NX-7530 single AC power supply server appliance with
RAID
Warnings
•Read all installation instructions and site survey reports, and verify correct equipment installation
before connecting the appliance to its power source.
•Remove jewelry and watches before installing this equipment.
•Verify the unit is grounded before connecting it to the power source.
•Verify any device connected to this unit is properly wired and grounded.
•Connect all power cords to a properly wired and grounded electrical circuit.
•Verify the electrical circuits have appropriate overload protection.
•Attach only approved power cords to the device.
•Verify the power connector and socket are accessible at all times during the operation of the
equipment.
•Do not install this equipment or work with its power circuits during thunderstorms or other weather
conditions that could cause a power surge.
•Verify there is adequate ventilation around the device, and ambient temperatures meet equipment
operation specifications.
Cautionary Statements
Caution
There are no user-serviceable components inside the NX-7500 series integrated services
platform. Opening the chassis will void the warranty.
Caution
BIOS settings on the NX-7500 series integrated services platform should not be changed.
Changing any settings in the BIOS will void the warranty on the integrated services platform.
Caution
To prevent the integrated services platformfrom overheating, never install in an enclosed area
not properly ventilated or cooled. For proper airflow, keep the front and back sides of the
integrated services platform clear of obstructions and away from the exhaust of other
equipment.
Hardware Installation
NX-7500 Series Integrated Services Platform 10

Caution
The recommended operating temperature is 32ºF to 104ºF/0ºC to 40ºC. Installation in a
closed or multi-rack assembly may raise the immediate ambient temperature above the
average room temperature. Exercise due caution.
Caution
Ensure the electrical circuit through which the integrated services platform is powered can
safely accommodate a 300 Watt power supply.
Caution
It is recommended you connect the NX-7500 series integrated services platform to an
Uninterruptible Power Supply (UPS). There are instances in which the system software could
become corrupt and un-recoverable in the event of power loss, for example, during a system
upgrade, database backup or database restore operation.
Site Preparation
•Consult your site survey and network analysis reports to determine specific equipment placement,
power drops, and so on.
•Assign installation responsibility to the appropriate personnel.
•Identify and document where all installed components are located.
•Provide a sucient number of power drops for your equipment.
•Ensure adequate, dust-free ventilation to all installed equipment.
•Identify and prepare Ethernet and console port connections.
•Verify cable lengths are within the maximum allowable distances for optimal signal transmission.
Safety Instructions for Rack Mount Installations
Rack Mount
Brackets
Do not lift the NX-7500 series integrated services platform using the rack mount brackets.
Rack Mount Rails Use only industry-standard mounting kits when installing the NX-7500 series integrated
services platforms, as improper mounting may result in hardware failure and hazardous
conditions. It is recommended to use the mounting rails included with the integrated
services platform.
Elevated Operating
Ambient
If installing the NX-7500 series integrated services platform in a closed or multi-unit rack
assembly, the operating ambient temperature of the rack environment may be greater than
the room ambient temperature. Consideration should be given to installing the appliance in
an environment compatible with the maximum ambient temperature (Tma) specified by the
manufacturer.
Reduced Air Flow Installation of the NX-7500 integrated services platform in a rack should be such that the
amount of air flow required for safe operation of the equipment is not compromised.
Mechanical Loading Mounting the NX-7500 integrated services platform in a rack should be such that a
hazardous condition is not achieved due to uneven mechanical loading.
Circuit Overloading Consideration should be given when connecting the NX-7500 series integrated services
platform to the supply circuit sothat protection is provided to the NX-7500 series integrated
services platfrom and supply wiring to avoid circuit overloads. Carefully review the
equipment nameplate ratings when addressing this concern.
Hardware Installation
NX-7500 Series Integrated Services Platform 11

Reliable Earthing Reliable earthing of the rack mounted NX-7500 integrated services platform should be
maintained.
Particular attention should be given to supply connections other than direct connections to the branch
circuit (e.g., use of power strips).
Installing the NX-7500 Series Integrated Services Platform
1 Follow the instructions supplied with the rail kit to mount the NX-7500 series integrated services
platform in an equipment rack.
2 Connect the power cords for all power supplies.
The following figure represents the back of the NX-7510 model with a single AC power supply:
The following figure represents the back of the NX-7520 model with two DC power supplies:
The following figure represents the back of the NX-7530 model with a single power supply:
NX-7500 Series Integrated Services Platform Power Supply
Installation
Warning
Power down the the integrated services platform and disconnect all power cords prior to
installing or replacing a power supply.
Caution
Ensure that the connectors at on the back of the power supply do not come into contact with
your hands or the packing material as you unpack the power supply. Avoid damaging the
connectors as you insert the power supply into the integrated services platform.
To remove a power supply and install a replacement power supply:
1 Remove the power cord from the power supply to be replaced.
2 Push the locking latch to the right and remove the power supply.
Hardware Installation
NX-7500 Series Integrated Services Platform 12

3 Unpack the AC or DC power supply module and carefully insert it into the NX-7500 integrated
services platform.
4 Press the locking latch to lock the power supply in place.
5 Observe that the power supply light is illuminated to verify that the power supply is operating
properly.
Installing an Additional Power Supply for NX-7510 or NX-7530 Integrated
Services Platform
To install an additional power supply for an NX-7510 or NX-7530 integrated services platform:
1 Unpack the AC or DC power supply module and carefully insert it into the NX-7510 or NX-7530
integrated services platform.
2 When installing a second power supply in an NX-7510 or NX-7530 integrated services platform,
remove the blank cover from the back.
3 Press the locking latch to lock the power supply in place.
4 Plug the power cord into the power supply.
5 Observe that the power supply light is illuminated to verify that the power supply is operating
properly.
Note
When two power supplies are installed, both power supplies should be properly connected
to a power source and powered up. An audible beep and display of a red LED indicates
that a power supply is not properly connected to a power source.
NX-7500 Series Integrated Services Platform NMC Installation
Warning
Power down the integrated services platform and disconnect all power cords prior to
installing or replacing the Network Mezzanine Card (NMC).
Hardware Installation
NX-7500 Series Integrated Services Platform 13

Caution
The NMC module uses lasers. The lasers are compliant with the requirements for a Class 1
laser product and are inherently eye safe in normal operation. However, you should never look
directly at any visible laser when the module is operational.
To install an NMC:
1 If the integrated services platform is running, perform a shutdown.
2 Wait until the LCD panel is no longer illuminated to confirm that the integrated services platform has
successfully shut down.
3 Disconnect all power cords from the integrated services platform.
4 Unlock the mounting latch on the blank NMC unit or functional NMC and pull the lever to remove.
Caution
Ensure that the connectors on the back of the NMC do not come into contact with your
hands or the packing material as you unpack the NMC. Avoid damaging the connectors as
you insert the NMC into the integrated services platform.
5 Remove the new NMC from the packing.
6 Carefully align and insert the NMC into the NX-7500.
7 Press the locking latch to lock the NMC in place.
8 Reconnect all power cords to the integrated services platform.
9 Apply power to the integrated services platform.
10 Verify that the integrated services platform LCD panel is illuminated.
11 Login in to the Management Interface and verify that the replacement NMC is operational.
NX-7500 Series Integrated Services Platform SFP Installation
The NX-7500 series integrated services platform supports use of SFP transceivers.
Note
SPF transceivers are keyed so that they can only be installed with the correct orientation.
To install a SFP transceiver:
Hardware Installation
NX-7500 Series Integrated Services Platform 14

1 Insert the SFP into the integrated services platform with the optical connector facing out and the
slot connector facing down.
2 Press the transceiver into the slot until it clicks into place.
Note
Only install 10Gb SPF+ transceivers in 10Gb NMC modules and 1Gb SPF transceivers in 1Gb
NMC modules.
NX-7530 Integrated Services Platform Disc Drive Assembly
Replacement
Warning
Power down the integrated services platform and disconnect all power cords prior to
installing or replacing the disc drive.
The NX-7530 integrated services platform configuration includes a hard drive disc assembly and
Redundant Array of Independent Disks (RAID).
To replace a disc drive assembly:
1 Remove power from the integrated services platform.
2 Press the release button on the right side of the disc drive assembly to release the assembly lock.
Hardware Installation
NX-7500 Series Integrated Services Platform 15

3 Pull the hard drive handle to the left and remove the hard drive from the drive bay.
4 Firmly insert the new disc drive assembly into the drive bay.
5 Push on the disc drive assembly until the lever locks in place.
6 Apply power to the integrated services platform.
When the new disc drive assembly is properly installed, the system rebuild will launch automatically.
This process may take up to two hours. To monitor the progress of the system rebuild, login to the
Command Line Interface (CLI) and enter the show raid command to display the current status.
NX-7510/NX-7520/NX-7530 Series Slide Rail Kit Installation
Instructions
Follow this procedure to install the slide rail for an NX-7500 series platform:
1 Using a Phillips head screwdriver, remove the mounting bracket screws from both sides of unit.
Note
Put the screws aside to be used when attaching the brackets for the slide rail.
Hardware Installation
NX-7500 Series Integrated Services Platform 16

2 Position the slide rail brackets so that the single hole at the front of the bracket is closest to the
bottom of the unit. Attach the slide rail brackets using the mounting bracket screws removed.
3 Refer to the instructions included with the slide rail kit to separate each slide rail into two pieces and
secure the outer slide rails to the rack using two screws on either end.
Hardware Installation
NX-7500 Series Integrated Services Platform 17

4 Using the four M4 screws supplied with the kit, attach the inner slide rails to the sides of the unit.
5 Align the inner and outer slide rails and carefully insert the unit into the rack.
Hardware Installation
NX-7500 Series Integrated Services Platform 18

6 When the front of the unit is flush against the rack, securely attach the unit using the two M3 screws
supplied with the kit.
Hardware Installation
NX-7500 Series Integrated Services Platform 19

3NX-7500 Series Specifications
Physical Specifications
Dimensions •1U, rack mountable
•17.2 in W x 1.76 in. H x 21.28 in. D
•430 mm W x 42 mm H x 532 mm D
Weight (with 1 power supply) •NX-7510 –19 lb./8.62 kg
•NX-7520 – 20 lb./9.07 kg
•NX-7530 – 21 lb./9.52 kg
Environmental Specifications
Operating Temperature 32°F to 104°F/0°C to 40°C
Storage Temperature -4°F to 167°F/-20°C to 70°C
Operating Humidity 5% to 85% RH at 104° F/40° C (non-condensing)
Storage Humidity 5% to 95% RH (non-condensing)
Power Specifications
Power Supply •NX-7510/ NX-7530 - 300 Watts, 100-240V AC
•PSU @ 50Hz-60Hz
•NX-7520 – 300 Watts, -48V DC
Typical Power Consumption 110 Watts
NX-7500 Series Integrated Services Platform 20