Extron electronics Cable Cubby 100 User manual

1
IMPORTANT:
Go to www.extron.com for the
complete user guide
,installation
instructions, and specifications.
Cable Cubby®100 • Installation Guide
This guide provides instructions for an experienced installer to install and connect the
Extron Cable Cubby 100.
he Cable Cubby 100 is a compact furniture-mounted enclosure for cable
access and connections. It can be installed quickly by using a common
4 inch (102 mm) hole saw.
Planning
Check with local and state regulations before starting the
installation:
Ensure that the planned installation complies with building and electrical codes.
Ensure that the planned installation complies with the Americans with Disabilities Act or other accessibility requirements.
Check all parts and equipment before installation:
Ensure that all parts are present in each kit.
Ensure that necessary tools and equipment are available for the installation.
Kit Contents
Tools Required for Installation
Safety Glasses
Phillips Screw Driver
Vacuum Cleaner
Marking Pen
Drill 4" (102 mm) hole saw
Grommet Plugs
(2) 3/8", (1) 1/4"
Connectivity Bracket
Cable Grommet Plate
#4-40 MAAP
Screws (4)
Cable Cubby 100
with top bezel
#4-40 Plate
Screws (4)
#6-32 Bracket Screws
with Washers (2)
#6 Mounting
Screws (4)

Cable Cubby 100 • Installation Guide (Continued)
2
Step 1 - Prepare the Furniture
Follow the instructions below to cut a hole in the surface where the enclosure will be installed. Read the following information
before making a cut.
Step 1a - Determine the best location for the enclosure.
Ensure that the location where the Cable Cubby is to be installed is convenient for as many users as possible.
Ensure that there is ample space under the furniture for cables. Allow at least 36 inches of cable loop for each cable (see
Step 4 –Route and Connect Cables on page 5).
Step 1b - Choose a method for cutting the hole in the furniture, and cut the hole.
CAUTION: Wear safety glasses when operating power equipment. Failure to comply can result in eye injury.
ATTENTION: Portez des lunettes de sécurité lorsque vous utilisez l’équipement électrique. Ne pas respecter cela peut
conduire à une blessure à l’oeil.
ATTENTION: The opening in the furniture for the Cable Cubby should be cut only by licensed and bonded
craftspeople. Exercise care to prevent scarring or damaging the furniture.
ATTENTION : L’ouverture dans la meuble pour le CableCubby devrait être coupée seulement par des artisans
autorisés et qualiés. Faites attention à ne pas faire de marques sur le meuble et à ne pas l’endommager.
Choose one of the following methods for cutting the hole:
Power Drill with 4 inch (102 mm) Hole Saw Jigsaw and Paper Cut-Out Template CNC Wood Router
Dimensions and cut-out templates are
available online on the product page at
www.extron.com.
Cut-Out Template forthe Extron
Cable Cubby 100
1. Confirm the product to be installed.
2. Remove the surface cut-out area
(gray) from the template.
3. Measure the cutout and template.
4. Mark the position on the
furniture where the Cable Cubby 1200
will beinstalled.
5. Cut the opening.
TrimRing
Lip
Cut-OutRadius:
0.25"(0.6cm)
0.00” (0.00 cm)
0.02 (0.05 cm)
+
P/N 68-2472-01 Rev.A
PageSize: 11" x 17"
Print Scale 1:1
Do not Shrink
Jigsaw
Cut-Out
Out Tem
Ca
Cabl
If using a CNC wood router
or other precise machinery,
use the exact cut-out
dimensions.
Cut-Out Dimensions:
4 inch (102 mm) round
diameter
NOTE: Insert the Cable Cubby 100 into the hole to test the t. If necessary, carefully enlarge the opening.
Step 1c - Drill the pilot holes into the furniture.
Follow these steps to drill the pilot holes for the Cable Cubby 100, then proceed to the next section.
1
Insert the Cable Cubby into the hole.
2
Position the Cable Cubby as you wish it to be installed on the furniture.
With the Cable Cubby in place, mark the four outermost holes
on the top surface.
Remove the Cable Cubby and drill
four pilot holes at the marked locations
on the furniture.
3

3
Step 2 - Install Connectivity Bracket and the MAAPs
Follow the steps below to populate the Cable Cubby enclosure.
Step 2a — Assemble and Install the Connectivity Bracket
Follow the steps below to assemble and install the connectivity bracket with the included cable grommet plate or optional
two-space MAAP module.
1
1
2
2
2
3
Insert cables into
the holes of the
grommet plate.
Use the #4-40 plate screws
to secure the grommet plate
on the connectivity bracket.
Snap the included hole
plugs into any unused
holes.
Insert the assembled module
into the bottom opening of the
enclosure.
Secure the module at the desired
height using the included #6-32
bracket screws.
Use the included #4-40 MAAP screws
to secure the two-space MAAP on the
enclosure.
USB CHARGER
1
Insert wires through
the opening shown
at the right and
wire the MAAP.
NOTE: Using the cap screws that
are not included with the MAAP
may not allow the bezel to t
properly.
1
1
2
2
2
3
Insert cables into
the holes of the
grommet plate.
Use the #4-40 plate screws
to secure the grommet plate
on the connectivity bracket.
Snap the included hole
plugs into any unused
holes.
Insert the assembled module
into the front opening of the
enclosure.
Secure the module at the desired
height using the included #6-32
bracket screws.
Use the included #4-40 MAAP screws
to secure the two-space MAAP on the
enclosure.
USB CHARGER
1
Insert wires through
the opening shown
at the right and
wire the MAAP.
2
S
h
b
NOTE: Using the cap screws that
are included with the MAAP may
1
1
2
2
2
3
Insert cables into
the holes of the
grommet plate.
Use the #4-40 plate screws
to secure the grommet plate
on the connectivity bracket.
Snap the included hole
plugs into any unused
holes.
Insert the assembled module
into the bottom opening of the
enclosure.
Secure the module at the desired
height using the included #6-32
bracket screws.
Use the included #4-40 MAAP screws
to secure the two-space MAAP on the
enclosure.
USB CHARGER
1
Insert wires through
the opening shown
at the right and
wire the MAAP.
NOTE: Using the cap screws that
are not included with the MAAP
may not allow the bezel to t
properly.
Step 2b — Install the MAAP plate(s) on the MAAP Opening on
applicable models
Follow the steps at the right to install a double-space
MAAP or two single-space MAAPs of your choice
(see www.extron.com for MAAP options and wiring
instructions). Install the MAAP in the MAAP opening as
shown at right.
To assemble the Cable Grommet Plate (included):
To assemble an optional MAAP module:
1
2
Wire the MAAP
.
Use the #4-40 cap scr
ews (included
with the MAAP) to secur
e the MAAP
on the connectivity bracket.
USB CHARGER

4
Step 3 - Mount the Cable Cubby in the Furniture
Follow the steps below to mount the Cable Cubby on the furniture.
CAUTION: The anged edges of the top of the surface enclosure are sharp. These edges are also soft and may be easily
nicked or bent. Exercise caution when handling the enclosure to prevent personal injury or damage to the enclosure.
ATTENTION: Les extrémités à brides du haut de la surface du boîtier sont aiguisées. Ces extrémités sont aussi lisses
et peuvent facilement être coupées ou pliées. Soyez prudents lorsque vous manipulez le boîtier an d’éviter de
l’endommager ou de vous blesser.
1
Insert the assembled
Cable Cubby 100
carefully into the
opening on the furniture.
2
Ensure that the Cable Cubby is fully seated on the
furniture surface.
Drive four mounting screws (included) through the
outer holes on the bezel and into the pilot holes
on the furniture to secure the enclosure.
I
nsert t
h
e assem
bl
e
d
C
able
C
ubby 100
care
f
ully into the
opening on the
f
urnitu
r
o
n t
r
e.
USB CHARGER
3
Snap the top bezel on the Cable Cubby.
Snap
the
top
bezel
on
the
Cable
C
ubb
USB CHARGER

5
Cable Cubby 100 • Installation Guide (Continued)
Step 4 - Route and Connect Cables
Follow the steps below to route and connect cables under the furniture.
1
23
2
3
Secure cables with zip ties
to the holes on the side of
the Cable Cubby.
For cable pass-through applications,
allow at least 36 inches (0.9 m) of cable
loop for each cable.
Connect cables to the AV system.
Step 5 - Connect AC Cord to Non-US Powered Models
Follow the steps below to connect the AC Cord to the Non-US Powered Models.
AC Power Cord
Retainer
If applicable, secure the AC
power supply cord with the
included cable retainer.

68-2797-01
Rev. B
09 16
6
Extron Headquarters
+800.633.9876 Inside USA/Canada Only
Extron USA - West Extron USA - East
+1.714.491.1500 +1.919.850.1000
+1.714.491.1517 FAX [phone] FAX
Extron Europe
+800.3987.6673
Inside Europe Only
+31.33.453.4040
+31.33.453.4050 FAX
Extron Asia
+65.6383.4400
+65.6383.4664 FAX
Extron Japan
+81.3.3511.7655
+81.3.3511.7656 FAX
Extron China
+86.21.3760.1568
+86.21.3760.1566 FAX
Extron Middle East
+971.4.299.1800
+971.4.299.1880 FAX
Extron Korea
+82.2.3444.1571
+82.2.3444.1575 FAX
Extron India
1800.3070.3777
(Inside India Only)
+91.80.3055.3777
+91.80.3055.3737 FAX
© 2016 Extron Electronics All rights reserved. All trademarks mentioned are the property of their respective owners. www.extron.com
Installation Checklist
Planning (page 1)
Check with local and state regulations before starting the installation
Check all parts and equipment before installation
Prepare the Furniture (page 2)
Determine the best location for the enclosure
Choose a method for cutting the hole in the furniture
Drill the pilot holes into the furniture
Install the Connectivity Bracket and the MAAPs (page 3)
Assemble and Install the Connectivity Bracket
Install a MAAP plate(s) on the MAAP Opening
Mount the Cable Cubby in the Furniture (page 4)
Mount the Cable Cubby ush with the furniture
Route and Connect Cables (page 5)
Connect AC Cord to Non-US Model (page 5)