Extron electronics DMP 64 Plus User manual

DMP 64 Plus • Setup Guide
This guide provides basic instructions for an experienced technician to install the DMP 64 Plus ProDSP™Digital Matrix Processor.
For more information, specications, and the user guide, see the DMP 64 Plus product page on www.extron.com.
Disconnect Power and Mount the DMP 64 Plus
Disconnect power from the DMP 64 Plus and turn off all devices that will be connected to it. The DMP 64 Plus is housed in a
half rack width, 9.5 inch deep, 1U high metal enclosure that can be rack mounted or placed on a table with the provided rubber
feet. Select a suitable mounting location, then choose an appropriate mounting option. Mounting information can be found in the
DMP64 Plus User Guide on www.extron.com.
Make all external device connections before applying power.
Rear Panel Connections
INPUTS
I/O
OUTS
DMP EXP
AT
ACP
REMOTE
USB AUD
LAN/VoIP
R
1 2 C V AT
1 (PRI) PoE+ 2 (SEC)
RS-232
Tx+V
IN G O IN G O IN G O IN G O IN G O IN G O
+S -S Rx GG
1 2 3 4 5 6 1 2 3 4
POWER
12V
2.0A MAX
1 2 3 4 5 6
A B C D E F G H
IJ K
Figure 1. DMP 64 Plus C V AT Rear Panel
APower Input — Connect the included external 2-pole captive screw power supply.
BEXP Port — Connect an EXP-enabled device to this RJ-45 port for a digital audio connection using Extron proprietary
protocol. Use the included one foot long shielded CAT 6 cable to connect two EXP-enabled devices to form a larger matrix
system. The expansion bus supports 16 bidirectional channels of audio (see the DMP 64 Plus User Guide for EXP bus
operation details).
CAT Ports (AT models only) — Two RJ-45 ports form a Gigabit switch that interfaces with the AT bus. The AT expansion bus
uses Dante®protocol for digital audio networking and allows DMP 64 Plus AT models to connect with other Dante-enabled
devices to form a larger matrix (see the DMP 64 Plus User Guide for operation details).
NOTE: Dante Controller software is required to configure the AT expansion bus. Dante Controller is available at
www.extron.com (see the DMP 64 Plus User Guide for instructions on installation and operation).
DACP Panel Port — Use a 4-pole 3.5 mm captive screw connector to connect an ACP
control device for configuration via DSP Configurator (wiring shown to the right).
ERS-232 Port — Use a 3.5 mm 3-pole captive screw connector to connect the host
RS-232 cable for bidirectional RS-232 (±5V) serial control (wiring shown to the right).
The default baud rate is 38400.
FLAN Ports — One RJ-45 port (non-V models) or two RJ-45 ports (V models) are
available for control network traffic (all models) and VoIP network traffic (V models
only). On DMP 64 Plus V models, the LAN/VoIP ports have multiple configuration options (refer to the DMP 64 Plus User
Guide for configuration options). On the Vmodels, by default, both control and VoIP traffic are transported on LAN/VoIP 1.
Port Default IP Address Default Subnet Mask Default Gateway Default DHCP
LAN 1 192.168.254.254 255.255.255.0 0.0.0.0 OFF
LAN 2 (V models only) 192.168.1.254 255.255.255.0 0.0.0.0 OFF
GUSB Audio Port — Connect a Windows or Mac computer to this USB mini-B port to interface with the DMP 64 Plus as a 4x4
USB audio device (see the DMP 64 Plus User Guide for additional USB audio interfacing capabilities).
G
Ground
+Signal
- Signal
+12 VDC
+V
- S
+S
RS-232
Tx Rx G
REMOTE
Transmit
Receive
Ground
Tx
Rx
G
1
IMPORTANT:
Go to www.extron.com for the
complete user guide, installation
instructions, and specifications.

HReset Button and LED — The reset button returns the DMP 64 Plus to different tiers of default states. When using the reset
function, the LED blinks to signify the different reset modes. When not using the reset function, the LED operates as a power
indicator and matches the front panel power LED (see the Reset Modes section of the DMP 64 Plus User Guide for more
information on the different reset modes).
IMic/Line Inputs — Use 6-pole 3.5 mm captive screw connectors to connect 6 balanced or unbalanced microphone or mono
line level sources (see 6-pole Audio Input Wiring below). Inputs 1 through 6 provide phantom power and AEC.
Tip
Slee
ve
Ring
Tip
Slee
ve
Ring
Tip
Sleeve
Tip
Sleeve
6-pole Audio INPUT Wiring
Balanced Input Unbalanced Input
Jumper
Jumper
Figure 2. 6-pole Audio Input Wiring
NOTES:
• Balanced or unbalanced stereo sources can be connected to the 6-pole inputs.
• When using the 5-pole CSR adapter, connect it so the far left plug is inserted into the far left jack of the 6-pole
input.
JDigital I/O Ports — Connect 6-pole 3.5 mm captive screw connectors to these ports. These configurable digital input and
output ports are designed to connect to microphones with logic circuitry for mic mute and tally back functionality. Each port
provides a common ground.
KLine Outputs — Use 6-pole 3.5 mm captive screw connectors to connect up to four balanced or unbalanced mono line level
devices or two stereo devices (see diagram below).
Tip
Sleeve
Tip
Sleeve
Tip
Slee
ve
Ring
Tip
Slee
ve
Ring
6-pole Audio OUTPUT Wiring
Balanced Output Unbalanced Output
NO Ground Here
NO Ground Here
Figure 3. Audio Output Wiring
ATTENTION:
• For unbalanced audio outputs, connect the sleeves to the ground contact. DO NOT connect the
sleeves to the negative (-) contacts.
• Pour l’audio asymétrique, connectez les manchons au contact au sol. Ne PAS connecter les manchons
aux contacts négatifs (–).
When all connections have been made, power up the input and output devices, then apply power to the DMP 64 Plus.
Front Panel Features
OUTPUTSINPUTS
ACTIVITY
CONFIG EXP
USB
LAN 1
LAN 2
DMP 64 Plus
DIGITAL MATRIX PROCESSOR
123456 1234
CLIP
SIGNAL
CLIP
SIGNAL
AB C D E
Figure 4. DMP 64 Plus Front Panel
APower LED — Blinks during boot up and lights steadily when the DMP 64 Plus is operational.
BUSB Config Port — One USB mini-B port is used for configuration. This port can also be used for firmware updates.
CActivity Indicator LEDs — These LEDs indicate activity or status on the rear panel EXP, LAN, and USB ports.
DInput Indicator LEDs — Stacked green and red LEDs display input signal presence and input signal clipping.
EOutput Indicator LEDs — Stacked green and red LEDs display output signal presence and output signal clipping.
Figure 2
2
DMP 64 Plus • Setup Guide (Continued)

DSP Configurator Software Installation
There are no hardware controls for the DMP 64 Plus. All conguration and control is done using ExtronDSPCongurator
software. Install DSP Congurator on a PC running Microsoft®Windows®. For full computer requirements, see the DSP
Congurator product page on www.extron.com.
Download DSP Configurator from the Extron Website:
1. From the Extron home page (www.extron.com), click the Download tab to open the Download page.
2. Under Software, on the left side of the page, select DSP Configurator Software. The DSPConfiguratorSoftware
product page opens.
3. Click the Download button and follow the on-screen instructions.
NOTE: An Extron Insider account is required to download DSP Configurator.
DMP 64 Plus Configuration
When power is connected to the DMP 64 Plus and the rest of the audio system, audio output can easily be tailored to any
listening environment. When conguration is required, changes are made using DSP Congurator.
Configure the DMP 64 Plus:
1. Ensure the control computer is connected to
the LAN port (recommended), front panel USB
Cong port, or RS-232 port of the
DMP 64 Plus. Full congurations that include
Macros, Internal Triggers (V models), and ACP
congurations require a LAN connection.
2. Start the DSP Congurator software.
a. From the splash screen drop-down
menu, select the DMP 64 Plus model
corresponding to the model connected to
the control computer.
a. Click OK and the main workspace opens.
3. The software starts in Emulate mode.
a. To create a conguration le ofine and
upload (push) that conguration to the
DMP 64 Plus at a later time, remain in Emulate mode and save the conguration le.
b. To push a conguration to the DMP64Plus or pull the current conguration from the DMP 64 Plus, enter Live mode.
When in Live mode, changes made in DSP Congurator affect the connected DMP64 Plus immediately. To enter Live
mode, click Live at the top of the DSP Congurator workspace, select Tools >Connect to Device, or press <F6>
on the keyboard.
NOTE: When Live mode is selected, a connection dialog box appears. Select the desired connection type and
follow the on-screen prompts (see the DMP 64 Plus User Guide for more information on connecting Live to a
device).
The main workspace provides access to mix matrices, gain blocks, and DSP processors for conguring the DMP 64 Plus. It also
provides a menu bar across the top with additional conguration tools. For more information about using DSP Congurator, see
the DSP Configurator Software section of the DMP 64 Plus User Guide or the DSP Configurator Help le that can be accessed by
selecting Help >Contents or pressing <F1> on the keyboard. Most dialog boxes within DSP Congurator contain a context-
sensitive Help button ( ) in the top right corner. Click this button to open the help le topic for that specic dialog box.
3

For information on safety guidelines, regulatory compliances, EMI/EMF compatibility, accessibility, and related topics, see the
Extron Safety and Regulatory Compliance Guide on the Extron website.
© 2019 Extron Electronics — All rights reserved. www.extron.com
All trademarks mentioned are the property of their respective owners.
Worldwide Headquarters: Extron USA West, 1025 E. Ball Road, Anaheim, CA 92805, 800.633.9876
Configure Dante Device Settings:
Dante settings on all DMP 64 Plus AT models can be congured from DSP Congurator. The Dante device can be named here,
which aids in device identication in the DanteController software when there are multiple Dante devices on the audio network.
ATTENTION: It is essential that a Dante device be named before audio subscriptions with other devices are
established. Existing subscriptions are removed when a device is renamed.
To configure Dante device settings:
1. Open DSP Congurator and connect Live to the DMP 64 Plus AT (see step 3b on the previous page).
2. Select Tools > Device Settings. The Device Settings dialog box
opens.
3. From the tabs at the top of the Device Settings dialog box, select Dante
Device.
4. In the Device name eld, give the DMP 64 Plus a meaningful name
(such as device model and location) so that it can be easily identied in
DanteController.
5. Dante device network settings can also be congured from this dialog box.
Use the radio buttons and text elds to choose DHCP (recommended) or
Static IP and enter a static IP address conguration.
NOTE: The device name and IP configuration in the Dante Device tab
only affect the Dante interface of the DMP64Plus. These settings do
not affect the device name recognized in DSP Configurator or the IP
address of the rear panel LAN port.
6. Select Enable Redundant Mode only if conguring the DMP 64 Plus for use
on redundant networks. A separate set of redundancy network settings opens
for conguration (see Physical Dante Network Setup in the DMP 64 Plus User
Guide for more information on redundant conguration).
7. Click Apply.
8. Click OK to conrm changes and close the Device Settings dialog box.
For more information on conguring a DMP 64 Plus in Dante Controller, refer to the Dante Controller section of the
DMP64 PlusUser Guide (www.extron.com).
68-3291-50 Rev. A
09 19