Extron electronics P/S 150 User manual

User’s Guide
Extron Electronics, USA
1230 South Lewis Street
Anaheim, CA 92805
USA
714.491.1500
Fax [phone]
Extron Electronics, Europe
Beeldschermweg 6C
3821 AH Amersfoort
The Netherlands
+31.33.453.4040
Fax [phone]
Extron Electronics, Asia
135 Joo Seng Road, #04-01
PM Industrial Building
Singapore 368363
+65.6383.4400
Fax [phone]
Extron Electronics, Japan
Daisan DMJ Building 6F
3-9-1 Kudan Minami
Chiyoda-ku, Tokyo 102-0074 Japan
+81.3.3511.7655
Fax [phone]
www.extron.com
© 2002 Extron Electronics. All rights reserved.
Universal 15V DC Power Supply
68-577-01 Rev. B
Printed in the USA
02 02
P/S 150
5
Channel Overload LEDs — These rear panel LEDs light
red to indicate that an overcurrent condition (1.8 amps or
more, or a short circuit) exists for the associated output.
When the Channel Overload LED lights for a specific
output, that output is switched off.
Specifications
Power input .................................. 100VAC to 240VAC, 50/60 Hz, 100 watts,
internal, auto-switchable
Power output ............................... 6 15VDC outputs (maximum current of
all outputs: 4.8 A )
Temperature/humidity ............. Storage
-40° to +158°F (-40° to +70°C) /
5% to 95%, non-condensing
Operating
+32° to +113°F (0° to +45°C) /
5% to 90%, non-condensing
Rack mount .................................. Yes, with optional rack shelf,
part #60-190-01
Enclosure type ............................. Metal
Enclosure dimensions ................. 1.75" H x 4.4" W x 8.5" D
4.4 cm H x 11.2 cm W x 21.6 cm D
Shipping weight ........................... 3 lbs (1.4 kg)
Vibration ....................................... ISTA/NSTA 1A in carton
(International Safe Transit Association)
MTBF ............................................. 30,000 hours
Warranty ...................................... 3 years parts and labor
Specifications are subject to change without notice.

P/S 150 • IndicationsP/S 150 • Installation
Installation
32
Description
The Extron P/S 150 is a 15VDC 5.0 A universal power supply with
six separate outputs on two 6-connector, 3.5 mm captive screw
connectors. The outputs are rated at 15V, 800 mA each. The
universal power supply can power up to six Twisted Pair (TP)
receivers or as many Extron architectural products as possible
without exceeding the P/S 150’s 4.8 A current limit.
The rack mountable P/S 150 has an internal auto-switchable
power supply that can accept 100VAC to 240VAC at 50 Hz to 60 Hz.
Installation
For optional rack mounting, mount up to four P/S 150s on a 19"
1U Universal Rack Shelf (Extron P/N 60-190-01) (figure 1).
(2) 4-40 x 1/8" screws
Use 2 mounting holes
on opposite corners
Half-rack
false front panel
uses 2 front holes
Quarter-Rack
False Front Panel
P/S150
15VDCPOWERSUPPLY
Figure 1 — Rack mounting the P/S 150
1. Mount the P/S 150 on the rack shelf, using two 4-40 x 1/8
screws in opposite (diagonal) corners.
2. If necessary, mount the half-rack false front panel (included
with the Universal Rack Shelf) and/or the quarter-rack false
front panel (included with the P/S 150) to the shelf, using
two 4-40 x 1/8 screws in the front holes for each panel.
Rear Panel Connections
1
Connect the power cables from the various devices that
will receive power from the P/S 150 to the 3.5 mm captive
screw connectors (included) (figure 2).
50/60 Hz 2.2 A MAX
1
100-240V -
CHANNEL OVERLOAD
POWER-GREEN
OVERLOAD-AMBER
15 VDC OUTPUT 800 mA PER CHANNEL
1 2 3 4 5 6
2
1
4
P/S 150
15VDC POWER SUPPLY
3
5
Figure 2 — P/S 150 front and rear panels
Each captive screw connector has six poles and can support
up to three power supply outputs (figure 3).
12345
– wire
+ wire
– wire
Up to 3 power
supply outputs
per connector
+ wire
Figure 3 — Connecting power cables to P/S 150
2
Connect the P/S 150 to an AC power source.
Operation
The minimum load for operation is 100 mA.
3
Power LED — This front panel LED (figure 3) lights to
indicate that the P/S 150 is receiving power.
4
Power/Overload LED — This rear panel LED lights green
when power is applied and is normal, and lights amber
when power is applied and an overcurrent condition (4.8
amps or more) exists.
CAUTION
Continued operation in an overload condition will
cause premature power supply failure.