Extron electronics System 8/10 Plus User manual

Extron • System 8/10 P LUS • User’s Manual • P/N 68-417-01 Rev. A
Toshiba Installation Configuration and Connections
SYSTEM 8/10 Plus
PROJECTOR COMMUNICATIONS KIT
ATTENTION!
PLEASE READ THIS DOCUMENT FOR IMPORTANT
INSTALLATION INSTRUCTIONS
THIS KIT HAS BEEN SHIPPED WITH THE FOLLOWING COMPONENTS:
Kit Type: TOSHIBA
Included Communications Adapter(s):
Quantity Part Number Description
1 26-471-01 ADP, UNV, “C”
THE TABLE BELOW LISTS THE POSSIBLE CONFIGURATION(S) AND CORRESPONDING
COMMUNICATIONS ADAPTER(S) FOR YOUR PROJECTOR MANUFACTURER’S VARIOUS
MODELS. PLEASE NOTE THAT YOUR SWITCHER HAS BEEN CONFIGURED AS
INDICATED BY THE “✔”IN THE “Config as” COLUMN. IF YOUR PROJECTOR MODEL
DIFFERS FROM THIS CONFIGURATION, YOU MUST RECONFIGURE YOUR SWITCHER
WITH THE CORRECT SETTINGS.
PLEASE REFER TO THE FOLLOWING PAGES FOR COMPLETE CONFIGURATION AND
SIGNAL CONNECTION INSTRUCTIONS.
THIS SWITCHER HAS BEEN CONFIGURED FOR: TOSHIBA P7300U
Config Model Rotary Switches Cable SW15 Settings Comm
as RS1 RS2 RS3 RS4 J2/J3 1 2 3 4 5 6 7 8 9 10 Adapter
✔Toshiba P7300U 0 0 4 A J2 ↓↓↑↓↑↓↓↓↑↓26-471-01

Extron • System 8/10 P LUS • User’s Manual • P/N 68-417-01 Rev. A
Toshiba Installation Configuration and Connections
Toshiba P7300U Projector Configuration
Verify that the System 8/10 PLUS is already configured for the Toshiba P7300U
projector. The general setup is explained on page 3-4 and the switch settings for
the projector are repeated below.
1. Use a small screwdriver to remove the access cover from the System 8/10 PLUS
front panel. See bottom of page 3-3. The label on the back of the access cover
also has the configuration information.
__________ Before changing anything, remove the AC power cord to the System 8/10 P LUS
to verify that the main power is OFF; also turn the projector power OFF.
2. Set the switches as follows:
Config Model Rotary Switches Cable SW15 Settings Comm
as RS1 RS2 RS3 RS4 J2/J3 1 2 3 4 5 6 7 8 9 10 Adapter
✔Toshiba P7300U 0 0 4 A J2 ↓↓ ↑ ↓ ↑
-↓ ↓↓↑↓ 26-471-01
_ RS5 is for RGB switching
delay. See page 3-4 for
more information on switch
functions.
3. Use a grease pencil (or other rub-off marker) to mark the space on the label next
to “Toshiba P7300U”.
4. Locate the switcher’s Address DIP switches on the rear panel, lower right.
Unless this is part of a master/slave system, set #3 and #5 to the up position and
the others down. See illustration to the left.
Use the illustration on the next page to do the following steps.
5. Connect the Comm Adapter’s 9-pin male connector to the 9-pin female “Remote
1” connector on the rear panel of the projector.
6. Connect the CC-50' (or CC-100') cable from the 9-pin male connector of the
Comm Adapter to the 15-pin HD “Projector Control” port located on the rear
panel of the System 8/10 PLUS.
______ Secure the screws on all D connectors.
7. Connect the BNC (RGBS) cables from the System 8/10 PLUS outputs to the
Toshiba P7300U projector inputs according to the application requirements.
8. Apply Main Power to the System 8/10 PLUS by connecting the power cord. The
Main Power LED should light. Apply power to the projector.
9. Return System 8/10 PLUS and projector to normal operation.
Configured For:
RS-232
34567891012
SW15 DIP Switch
ON
RS5 RS2
RS2
RS1
RS3
RS4
RS1
RS3 RS4
Page 1

Extron • System 8/10 P LUS • User’s Manual • P/N 68-417-01 Rev. A
Toshiba Installation Configuration and Connections
Toshiba P7300U Projector Connections
Use the illustration below when connecting the System 8/10 PLUS to a Toshiba
P7300U projector. Refer to Toshiba documentation to continue the installation.
_ If the installation includes looping (master/slave) switchers, see Chapter 5.
If Video Loop Back is part of the installation, see pages 2-10 and 2-11.
Page 2
CC 50'
G/G Sync B VH/Sync
OutIn
RG/Y B/Pb VH/Sync R/Pr
RGB 1 IN RGB 2 IN
Remote 1
S-VideoVideo System Bus Remote 2 Y/C IN
YC
OutIn In
25-Pin
15-Pin HD
26-471-01
"C"
"C"