Extron electronics USB HUB4 Series User manual

USB HUB4 Series • Setup Guide
This guide provides basic instructions for setting up the
Extron USB HUB4 Series AAP and MAAP.
HUB4 USB MAAP HUB4 USB AAP
ACTIVITY ACTIVITY
USB HUB4 MAAP USB HUB4 AAP
ACTIVITY ACTIVITY
Installation
Step 1 — (Optional) Install the wall box or mounting bracket
If using an electrical wall box or a mounting bracket, install it in the wall or furniture (see
Mounting in the USB HUB4 Series User Guide available at www.extron.com).
Step 2 — Mount the HUB4 onto a mounting frame
Attach the USB HUB4 AAP or USB HUB4 MAAP to an appropriate AAP or MAAP sized
mounting frame, rack space frame, or other Extron architectural product (see Mounting in the
USB HUB4 Series User Guide).
Step 3 — Connect the USB HUB4 to the host computer
For ease of installation, connect the USB HUB4 to the host computer in either of the following
ways:
• Using the Type mini-B USB port: Connect a Type A to
Type mini-B cable (provided) to the USB mini-B port on
the USB HUB4 rear panel.
• Using the green captive screw USB In port: Remove
the Type B or Type mini B terminator from a Type A to B
or Type A to mini-B USB cable and insert the cable wires
into the 5-pole USB In port as shown below and at right.
This method may be necessary if space is limited.
(See Connecting to the captive screw USB port in the
USB HUB4 Series User Guide.)
Wire color Port
Braided shield
V+ (+5 VDC)
Red
S (Shield)
White D- (Data -)
Green D+ (Data +)
Black –(Ground)
NOTE: Choose one of these two methods to connect the HUB4 to the host
computer. Do not connect the host computer to both HUB4 ports at the same time.
USB IN
RWGB
+V D- D+ S
IN OUT
WIRE COLOR
POWER
12V
1.1A MAX
+
+
--
-
Braided Shield / S
Red / +V
White / D
-
Green / D+
Black /
USB Cable (6’)
To Host
Computer
USB Port
Type A
USB
Strip 1”to 2”from the outer jacket
of the USB cable to expose the wires.
USB HUB4 AAP
Captive
Screw
USB
Connector
Type mini B
USB Connector
Mounting
Frame
Rear
IMPORTANT:
IMPORTANT:
Go to www.extron.com for the complete
user guide, installation instructions, and
specifications before connecting the
product to the power source.

For information on safety guidelines, regulatory compliances, EMI/EMF compatibility, accessibility,
and related topics, see the Extron Safety and Regulatory Compliance Guide on the Extron website.
USB HUB4 Series • Setup Guide (Continued)
68-1735-50
Rev. B 06 22
© 2009-2021 Extron — All rights reserved. www.extron.com
All trademarks mentioned are the property of their respective owners.
Worldwide Headquarters: Extron USA West, 1025 E. Ball Road, Anaheim, CA 92805, 800.633.9876
Step 4 — (Optional) Wire power connector
The USB HUB4 can be powered by the host computer.
However, if the USB peripheral devices connected to the
USB HUB4 require more power than the USB HUB4 can
provide, wire an optional Extron PS 1215 1.5 A, 12 VDC
power supply to the 12VDC Power In ports 1 and 2 on the
rear panel, as shown at right.
Connecting additional Extron devices
If using an additional Extron device, such as a WM Series
Extender, with the external power supply, connect the device
power cord to the 12 VDC Power Out ports 3 and 4 (see
image below).
USB IN
RWGB
+V D- D+ S
IN OUT
WIRE COLOR
POWER
12V
1.1A MAX
+
+
--
-
SECTION A–A
Power Supply
Output cord
A
Maximum: Maximum peaking
and gain
Medium: Mid-level peaking
and gain
Normal: Unity gain
Circuit
board
Faceplate
www.extron.com
33-612-01 D
02 05
9-18 VDC
Power
L
Audio
R
EXTENDER WM AAP
AUDIO IN
USB HUB4 AAP
ACTIVITY
USB IN
RWGB
+V D- D+ S
IN OUT
WIRE COLOR
POWER
12V
1.1A MAX
+
+
--
-
Rear
Front
Extender WM AAP
USB HUB4 AAP Desktop Powe
r
Supply
Power Loop Out
Step 5 — (Optional) Mount unit in wall box
If using an electrical box, mount the USB HUB4 and
the attached mounting frame onto the box (see the
image at right). If using a mounting bracket, this step
is not needed.
Step 6 — Connect peripheral devices
Attach the peripheral USB devices to the front panel
USB Type A ports.
Step 7 — Power on
Power on the host computer and the desktop power
supply (if applicable). Check the front panel power
indicator LED to verify that the HUB4 is receiving
power.
Wall opening
flush with
edge of box
Extron
CPM101
Mounting
Frame
Extron
USB HUB4
USB Hub
VTT001MAAP
POWER
USBHUB4 MAAP
ACTIVITY