Extron electronics 4xi series User manual

Extron • System 4 xi Switcher Series • User’s Manual • P/N 68-427-02 Rev. B
Configuration and ConnectionsToshiba TLP Installation
SYSTEM 4xi
PROJECTOR COMMUNICATIONS KIT
ATTENTION!
PLEASE READ THIS DOCUMENT FOR IMPORTANT
INSTALLATION INSTRUCTIONS
THIS KIT HAS BEEN SHIPPED WITH THE FOLLOWING COMPONENTS:
Kit Type: TOSHIBA (LCD)
Included Communications Adapter(s):
Quantity Part Number Description
1 26-474-01 ADP, UNV, “F”
THE TABLE BELOW LISTS THE POSSIBLE CONFIGURATION(S) AND CORRESPONDING
COMMUNICATIONS ADAPTER(S) FOR YOUR PROJECTOR MANUFACTURER’S VARIOUS
MODELS. PLEASE NOTE THAT YOUR SWITCHER HAS BEEN CONFIGURED AS
INDICATED BY THE “✔”IN THE “CONFIG AS”COLUMN. IF YOUR PROJECTOR MODEL
DIFFERS FROM THIS CONFIGURATION, YOU MUST RECONFIGURE YOUR SWITCHER
WITH THE CORRECT SETTINGS.
PLEASE REFER TO THE FOLLOWING PAGES FOR COMPLETE CONFIGURATION AND
SIGNAL CONNECTION INSTRUCTIONS.
THIS SWITCHER HAS BEEN CONFIGURED FOR: TOSHIBA TLP 710U/711U
CONFIG MODEL SW1 SW2 SW3 SW4 SW5 SW6 PROJ COMM
AS 1 2 3 4 CABLE ADAPTER
✔Toshiba 710U/711U off on off on 0 0 3 E 0 J15 26-474-01

Extron •System 4 xi Switcher Series •User’s Manual •P/N 68-427-02 Rev. B
Toshiba TLP Installation Configuration and Connections
(Note: Information depends on
S
y
stem 4
x
i setup.
)
(See note.)
(See note.)
(See note.)
(See note.)
[System 4 xi model and software
version displayed here]
Connecting System 4xi to Toshiba TLP 710U/711U Projector
If the System 4xi is already configured for a Toshiba 710U/711U projector, go to
step 4. If it is not set up correctly, it will be necessary to change switch settings
on the System 4xi ’s Main Controller Board. Begin at Step 1 to verify the correct
configuration.
1. Use the Front Panel to display the Information Menu to verify that the System 4xi
is already set up for the Toshiba projector. Apply power to the System 4xi and do
the following:
a. Press to display the MENU SELECT on the LCD screen.
b. Press or to step to Menu 8.
c. Press to select this menu.
d. Press or to display the configuration. The example to the left is general,
yours will show the System 4xi model name, the software version and the
following information:
PRJ = TOSHIBA
PRJ BAUD = 9600
UNIT No. = 000
HST BAUD = 9600 (value depends upon setup Menu 3)
2. Go to the procedure on page 2-3 of the System 4 xi User’s Manual to remove the
System 4xi cover. Then go to page 2-4 and refer to the configuration below to
set up the Main Controller board. Continue with Step 3 (below) when the
configuration is correct.
Config Projector SW1: 1-2-3-4 SW2 SW3 SW4 SW5 SW6 Prj Cable Comm
as Adapter
✔Toshiba 710U/711U off-on-off-on 0 0 3 E 0 J15 26-474-01
3. Double-check your work and be sure the System 4xi cover is on securely.
4. Install the System 4xi in its place of operation (i.e. rack), but not powered on.
__________ Changes in some switch configurations are not detected until the power is
removed at the AC cord, and then restored.
Refer to the following connection diagram and continue.
5. The Toshiba Comm Adapter (26-474-01) has a 9-pin male connector that
accommodates the Comm Extension cable. The other end of the Comm Adapter
plugs into the projector’s 15-pin “RS-232C”port.
Page 1
}
SW1
ON
SW2
SW4
SW3 SW5
J15
34
12

Extron •System 4 xi Switcher Series •User’s Manual •P/N 68-427-02 Rev. B
Configuration and ConnectionsToshiba TLP Installation
6. Plug the 15-pin HD connector of the Projector Communications Extension cable
into the PJ Comm port on the System 4xi.
______ Secure all of the connector screws.
7. Plug the (4 or 5) BNC connectors from one end of the (user-supplied) RGBS/HV
cable onto the System 4xi output. Then connect the 15-pin male connector on
the other end of the RGBS/HV cable into the “RGB1 IN”port of the projector.
System 4xi Series –Toshiba TLP 710U/711U Projector Connections
Use the illustration below as a guide when connecting the System 4xi to a
Toshiba 710U/711U projector. Refer to Toshiba documentation to continue the
installation.
____________ In a rack mount, do NOT allow the weight of the cables to be supported by the
System 4 xi . See page 2-5 for cabling guidelines.
Page 2
COM Adapter
26-474-01 9-pin
CC 50'
15-pin
15-pin
○○○○○○○○○○○