FAAC N1D KIT User manual

N1D KIT
N1D AUTO KIT
N1D SENSO KIT

ND1 2 732558 - Rev. D
WARNINGS FOR THE INSTALLER
GENERAL SAFETY REQUIREMENTS
EC DECLARATION OF CONFORMITY
Manufacturer: FAAC S.p.A.
Address: Via Calari, 10 - 40069 Zola Predosa BOLOGNA - ITALIA
Declares that: The operator mod. N1D Kit, N1D auto Kit, N1D senso kit
• conforms to the essential safety requirements of the following EEC directives:
2006/95/EC Low Voltage Directive
2004/108/EC Electromagnetic Compatibility Directive
99/05/ECRTTE Directive
• conforms to that foreseen by the following harmonised standards:
- EN 60335-2-103
- EN 61000-3-2, EN 61000-3-3
- EN 55014-1, EN 55014-2
Bologna, 01-07-2014
CEO
A. Marcellan
1. ATTENTION! It is important for the safety of people to follow all
the instructions carefully. Incorrect installation or incorrect use
of the product could cause serious harm to people.
2. Read the instructions carefully before installing the product.
3. The packaging materials (plastic, polystyrene, etc.) must not
be left within reach of children as they are potential sources
of danger.
4. Keep these instructions for future reference.
5. This product was solely designed and built for the use described
in this document. Any other use, not specifically described, could
compromise the integrity of the product and/or be a source of
danger.
6. FAAC declines all liability deriving from improper use or use
other than that for which the automated system is intended.
7. Do not install the equipment in an explosive atmosphere: the
presence of flammable gas or fumes is a serious safety risk.
8. FAAC is not responsible for failure to comply with GoodTechnical
Practice when constructing the closing elements that are to be
motorised or for any deformation that may occur during use.
9. Before performing any operation on the system, disconnect the
power supply.
10. Installation must be performed by skilled technical personnel
and in compliance with regulations in force.
11. The power mains of the automation system must be fitted with
a multi-pole power switch with a switch-contact gap of at least
3 mm. It is advisable to use a 6A circuit breaker with a multi-pole
power switch.
12. Verify that there is a differential switch with a 0.03 threshold
upstream of the system.
13. For outdoor use, install the electric cables inside specific pro-
tective conduit.
14. Verify that the earthing system is perfectly constructed and
connect the metal closing parts.
15. Do not connect more than one engine to the same inverter.
16. Do not connect two inverters to the same engine.
17. FAAC declines all liability concerning safety and the automated
system working properly, if system components not manufac-
tured by FAAC are used.
18. Only use original FAAC parts for maintenance.
19. Do not modify the components of the automated system in
any way.
20. The appliance must always be visible when handled.
21. Do not allow children or adults to stay near the product during
operation.
22. Keep radio controls or other pulse generators out of the reach of
children to prevent the automation system from being activated
involuntarily.
23. The user must not attempt any kind of repair or direct interven-
tion and must only contact qualified personnel.
24. Anything not specifically stipulated in these instructions is not
permitted.

ND1 3 732558 - Rev. D
1
27
6
5
34
8
ND1ND4
1
3
8
10 11
12
2
4
5
6
7
13
14
17
15
18
19
20
21
22 23
9
16
9
1 TOOLS REQUIRED
N1D KIT
1. Level
2. Drill with appropriate drill bits
3. 1 x 10 mm box wrench
1 x 18 mm box wrench
4. Hammer
5. Phillips screwdriver
6. Pencil
7. Saw for metals
8. Tape measure
9. Key or T40 TORX screwdriver
2 COMPOSITION OF THE KIT
Fig. 1
Fig. 2
1. Engine chassis: profile containing the
engine
2. Transmission frame: empty profile
3. Cover casing
4. Cover caps
5. 1 cable gland
6. Wired control (for N1D kit and N1D
AUTO kit)
7. Single channel remote controlTM XT1
433 (N1D SENSO Kit)
8. 2 spring washers
9. 2 tie rods (8x80)
10. Fast transmission (grey)
with reinforcement
11. Slow transmission (yellow)
with reinforcement
12. Transmission axis
13. 2 screws (6x50)
14. 2 lock washers
15. 4 screws for guides (5x35)
16. 2 drive rings
17. 2 screws (12x20)
18. 2 reversible rollers
19. 2 safety screws
20. 2 nuts
21. Transmission arms (ND1 or ND4
depending on markets)
22. 2 guides
23. 4 guide caps

ND1 4 732558 - Rev. D
First of all, check that the shutter works properly. If need-
ed, lubricate the hinges and level the shutter. (Fig. 3.1)
3 PRELIMINARY OPERATIONS AND TECHNICAL SPECIFICATIONS
3.2 Checking shutter operation
The following table describes the application limits for the various kits.
3.1 Application limits
Fig. 3.1
MODEL COMPARTMENT MAXIMUM WIDTH (mm)
(* cutting the casing and shaft)
COMPARTMENT MAXIMUM WIDTH
(mm)
N1D KIT 1 LEAF 672 (* 600) 1100
2 LEAVES 850 (* 780) 1400
N1D AUTO KIT 1 LEAF 760 (* 660) 1400
2 LEAVES 960 (* 860) 1600
N1D SENSO KIT 1 LEAF 760 (* 660) 1400
2 LEAVES 960 (* 860) 1600
Automations of the N1D line are designed to automate shutters in the 16 congurations described in chapter 4.
In the case of a double leaf application, the opening angles of the two leaves must be identical.
Dierent models require dierent modes of operation:
1) N1D KIT : controlled by distinct opening / closing buttons, with dead man logic. The N1D model kit does not require automatic limit
switches.
2) N1D AUTO KIT : controlled by distinct opening / closing buttons. The N1D model AUTO kit requires automatic limit switches that recog-
nise the mechanical opening and closing stops and interrupt the stroke.
3) N1D SENSO KIT : remote controlled and by a step logic button (optional). The opening and closing limit switches are set during the
learning stage. The automation recognises the presence of obstacles during the stroke.
N1D KIT N1D AUTO KIT N1D SENSO KIT
POWER SUPPLY VOLTAGE 230V 50-60Hz
POWER 130W 180 W 180 W
OPENING/CLOSING TIME About 16 seconds
POWER SUPPLY CABLE OUTLET Right or left
RAL CASING White RAL 9010 or Brown RAL 8017
CONTROL Dead man switch Switch
Opens/Closes
FAAC 433 MHz radio transmitter
or step button

ND1 5 732558 - Rev. D
3mm
3mm
ND1 arm 150 mm min.
ND4 arm 100 mm min.
Closed shutter
Guide Arm
Window
The minimum depth with the ND4 arm supplied in
the kit is 100 mm. For dierent arms, see chapter 12 on the
optional arm range
3.4 Indications
The frame must be installed with the bevelled angle facing outwards. (Fig. 3.4 and Fig. 3.5)
Fig. 3.3
Fig. 3.4 Fig. 3.5
The minimum depth with the ND1 arm supplied in
the kit is 150 mm. For dierent arms, see chapter 12 on the
optional arm range
Close the shutters, trace a line from the inside 3 mm from the closed shutter, on the architrave or on the windowsill according to the
chosen installation.
This line will delimit the position of the frames. (Fig. 3.2)
3.3 Reference mark
Fig. 3.2

ND1 6 732558 - Rev. D
The shutter closing delay is always seen from the inside.
4 SELECTING CONFIGURATION
Architrave assembly
Right delay
Right cable outlet
Architrave assembly
Right delay
Left cable outlet
Architrave assembly
Left delay
Right cable outlet.
Architrave assembly
Left delay
Left cable outlet
Assembly on the windowsill
Right delay
Right cable outlet
Assembly on the windowsill
Right delay
Left cable outlet
Assembly on the windowsill
Left delay
Right cable outlet
Assembly on the windowsill
Left delay
Left cable outlet

ND1 7 732558 - Rev. D
Architrave assembly
Right shutter
Right cable outlet
Architrave assembly
Right shutter
Left cable outlet
Architrave assembly
Left shutter
Right cable outlet
Architrave assembly
Left shutter
Left cable outlet
Assembly on the windowsill
Right shutter
Right cable outlet
Assembly on the windowsill
Right shutter
Left cable outlet
Assembly on the windowsill
Left shutter
Right cable outlet
Assembly on the windowsill
Left shutter
Left cable outlet

ND1 8 732558 - Rev. D
1
2
1
2
5
467
3
1
2
L - 760 mm (N1D SENSO / AUTO)
L - 672 mm (N1D)
172 mm
Arrange the pieces as in g. 5.
External
Internal
L = architrave length
1. Right shutter
2. Left shutter
3. Fast transmission (grey)
5 CONFIGURATION N° 1, 2 and 3, 4
4. Transmission frame
5. Transmission axis
6. Engine chassis
7. Slow transmission (yellow)
Depending on the selected N1D model, cut the transmission axis (Fig.6 ref. 2) according to measurement A (Fig.5 ref. A), according to the
following formulas:
N1D SENSO / AUTO : A= Architrave length - 760 mm
N1D : A= Architrave length - 672 mm
Eliminate burrs from the transmission axis in line with the cut made.
Insert the transmission axis into the hexagonal prole of the engine chassis.
1. Engine chassis
2. Transmission axle
5.1 Transmission axis insertion
External
Installation in
SUPPORT from TOP view
Installation on ARCHITRAVE from BOT-
TOM view
Fig. 5
Fig. 6
A = transmission axis length =

ND1 9 732558 - Rev. D
A
Only for settings 2 and 3:
pass the cable through the specic PVC tube (see image Fig. 7).
ATTENTION: the electric cable must not be in contact with any movable part.
ATTENTION: It is essential to keep the cable fully stretched.
Insert the transmissions at each end, making sure the reinforcing screws are properly secured.
Insert the hexagonal transmission axis in the return slot.
Insert the transmission axis into the engine chassis and tighten the grub screw A. (Fig. 8)
5.3 Assembly
5.2 Cable outlet
Fig. 7
Fig. 8
To facilitate the operation, use a N°10 span-
ner to turn the hexagon of the transmission.

ND1 10 732558 - Rev. D
Make sure that the frames are aligned.
Use the level to check that the device is horizontal.
Set the supplied toothed washers in place and tighten the tie rods using a T40 Torx wrench.
Proceed as described in Chapter 9.
5.5 Fixing the frame
5.4 Fixing holes
Assemble the pieces and place them under the architrave or on the windowsill (installation on the architrave in gure 9).
Mark the position of the holes on the frames and drill with the appropriate bit.
Place the dowels adequate for the material on which the N1D will be installed.
ATTENTION: The quality of the fastening is essential for the device to work properly. For this, the dowels must be adequate
for the type of fastening material and 8x80 screws.
Fig. 9
Fig. 10