FAAC ParQube FC User guide

ParQube FC
Fee Computer
Use and maintenance
Ver. 1.0
July, 2015
en
Instructions translated from the original Italian

3 / 36
Ver. 1.0 - July, 2015 - EN
MANUFACTURER
FAAC S.p.A.
Soc. Unipersonale
Via Calari 10
40069 Zola Predosa (BO)
Italy
INTRODUCTION
This documentation is part of the operating instructions of the parking system.
If this manual should contain incomplete or dicult to understand information, it is mandatory to consult the installer: no
initiative is to be taken.
GENERAL INFORMATION
FAAC S.p.A. requires installers and users to strictly comply with the instructions described in this manual, paying particular
attention to the safety warnings.
GENERAL CONSIDERATIONS
All operating and maintenance instructions and warnings given in this manual must be complied with.
Training the personnel responsible for the product is of particular importance, especially with regards to the use, as well as
maintenance and monitoring of compliance with the operating procedures and all safety regulations in this manual.
This manual has been drawn up with the greatest possible care, with the aim of providing accurate information. However,
FAAC S.p.A. declines all explicit and implicit liability for any errors contained in this document.
Moreover, FAAC S.p.A. reserves the right to modify the contents of this manual at any time and without prior notice in order
to keep it up to date.
FAAC S.p.A. shall not be held responsible for errors or data loss deriving from the use of this manual.
ORIGINAL VERSION IN ITALIAN
Versions of this document in a language dierent from the original must be understood to be a direct translation of the
original Italian version.
PREFERENTIAL RIGHT OF INTERPRETATION
In the event of any dierences between the translated and the original version, the Italian version shall be considered the
only valid version published and recognised by FAAC S.p.A.
COPYRIGHT INFORMATION
No part of this publication may be reproduced, distributed, translated into any language or transmitted by any means,
electronic or mechanical, including photocopying, recording or with any other storage and retrieval systems, for other pur-
poses other than the exclusive personal use of the purchaser, without specic written permission from FAAC S.p.A..
FAAC S.p.A. thanks you for choosing our products

4 / 36 Ver. 1.0 - July, 2015 - EN
Copyright ©, 2015, FAAC S.p.A.
All rights reserved. The information contained herein is considered accurate as at the date of publication.

5 / 36
Ver. 1.0 - July, 2015 - EN
Table of Contents
1 Graphic conventions .................................................................................................................................8
1.1 General symbols..........................................................................................................................................................................8
1.2 Symbols for procedures ............................................................................................................................................................8
1.2.1 Table with the symbols for procedures................................................................................................................................................... 9
1.3 Roles............................................................................................................................................................................................. 10
2 General Conditions.................................................................................................................................. 12
2.1 Symbols applied to the Product............................................................................................................................................ 12
2.2 General Warnings ..................................................................................................................................................................... 12
2.3 Limitations of liability................................................................................................................................................................ 12
2.4 Recipients.................................................................................................................................................................................... 12
3 Product Description ................................................................................................................................ 14
3.1 Intended use .............................................................................................................................................................................. 14
3.1.1 Limitations of use ........................................................................................................................................................................................14
3.1.2 Storage ..........................................................................................................................................................................................................14
3.2 Technical characteristics........................................................................................................................................................... 15
3.2.1 Control elements.........................................................................................................................................................................................15
3.3 General description .................................................................................................................................................................. 16
3.3.1 Functionality .................................................................................................................................................................................................16
4 Use...............................................................................................................................................................20
4.1 Use by the operator ................................................................................................................................................................ 20
5 Maintenance ............................................................................................................................................ 24
5.1 Introduction............................................................................................................................................................................... 24
5.2 Safety warnings ........................................................................................................................................................................ 25
5.3 Service and Maintenance planning systems..................................................................................................................... 26
5.3.1 Peripheral .....................................................................................................................................................................................................26
5.3.2 Ticket/receipt printer .................................................................................................................................................................................26
5.4 Peripheral................................................................................................................................................................................... 27
5.4.1 Opening service door............................................................................................................................................................................... 27
5.4.2 Closure service door ................................................................................................................................................................................. 27
5.4.3 Switching on and o .................................................................................................................................................................................28
5.5 Ticket/receipt printer............................................................................................................................................................... 29
5.5.1 Paper roll replacement..............................................................................................................................................................................29
5.5.2 Clearing jams................................................................................................................................................................................................31
6 Declaration of Conformity.................................................................................................................... 34

6 / 36 Ver. 1.0 - July, 2015 - EN
This page intentionally left blank

7 / 36
Ver. 1.0 - July, 2015 - EN
Capitolo 1
GRAPHIC CONVENTIONS

8 / 36 Ver. 1.0 - July, 2015 - EN
1 GRAPHIC CONVENTIONS
1.1 GENERAL SYMBOLS
The following table shows the general symbols used in the manual.
Symbol Description
Indicates warnings or procedures related to operator safety.
Indicates warnings or information of particular importance which do not aect operator safety.
Indicates a reference to a specic manual
Indicates a reference to a chapter in this manual
Indicates a reference to a section in this manual
1.2 SYMBOLS FOR PROCEDURES
Each procedure reports, next to the title, an icon indicating the role to be performed.
In addition, certain repetitive procedures are associated with an icon that will be used to recall them each time they should
be executed.
Apertura sportello di servizio
P
12 3
Figure 1 - Example of a title of a procedure
Pos Description
1Title procedure
2Icon identifying the procedure (for recursive procedures only)
3Minimum role to perform the procedure

9 / 36
Ver. 1.0 - July, 2015 - EN
1.2.1 Table with the symbols for procedures
Icon Description
Indicates the opening of service door
Indicates the closing of the service door
Indicates the activation of the security measures
Indicates the deactivation of the security measures
ONON
Indicates the switching on
OFFOFF
Indicates the switching o
Indicates the connection
Indicates the disconnection
Indicates the cleaning
Indicates the insertion of the tickets or card
Indicates the withdrawal of the tickets or card
Indicates the emptying of the bin
Indicates the Login phase

10 / 36 Ver. 1.0 - July, 2015 - EN
1.3 ROLES
The following table indicates the expertise and qualications required of the operators assigned to the dierent tasks:
Icon Qualication Description Responsibility
INSTALLER
▫Technician
HUB Parking Technology
▫Technician who has
received specic training
from the manufacturer.
▫System installation according to the
intended purpose.
▫Commissioning according to the
operating and safety requirements and
delivery to the system manager.
▫Training of operational personnel to
ensure safe operation.
▫System maintenance by repairing or
replacing components.
MAINTENANCE TE-
CHNICIAN
▫Technician
HUB Parking Technology
▫Technician or employees of
the parking area trained by
the manufacturer.
▫System maintenance by repairing or
replacing components.
▫Cleaning of the equipment in accordance
with the manufacturer's instructions.
▫Immediate and safe reaction in case of
faults.
SYSTEM MANAGER ▫Car park owner
▫Parking employee
▫Ensure that maintenance is performed
only by authorised technicians
▫Ensure that all safety regulations are
observed
▫Check that the operators have specic
training
PP
OPERATOR ▫Parking employee.
▫Operation of the peripherals during
normal use.
▫Cleaning of the equipment in accordance
with the manufacturer's instructions.
▫Immediate and safe reaction in case of
faults.