Faber Vejen User manual

Installation manual Vejen
40011673-1904 Vejen ENG

Installation manual
2
1.0
2.0

Installation manual
3
3.0
4.0 4.1

Installation manual
4
4.2 4.3
5.0 5.1

Installation manual
5
5.2 5.3
6.0a 6.0b

Installation manual
6
7.0
8.0

Installation manual
7
9.0
10.0b
10.0d
10.0a
10.0c
10.0e

Installation manual
8
1 Dear user
Congratulations on purchasing your Faber product, a quality
product that will provide you with the warmth and atmosphere for
many years. Please read the user manual before using the re.
Should a malfunction occur despite the careful nal checks, then
you can always contact your Faber dealer.
In order to claim the guarantee, it is important that you register the
re. For this we have created a special site. You will nd all
information regarding the warranty during registration.
> Please note:
The data of your re is available in the user manual.
1.1 Introduction
Installation and maintenance of the re must be carried out by a
professional expert who has proven knowledge and demonstrable
competence. A professional craftsman takes into account all
technical aspects such as heat delivery, gas connection as well as
ue gas discharge requirements.
Where the installation instructions are not clear, he must follow
national / local regulations.
1.2 Please check
You can register your re at: www.faber-res.eu
Check the re for transport damage and report any damage
immediately to your dealer.
1.3 CE-declaration
Glen Dimplex Benelux certies that this Faber re complies with the
essential requirements of the gas appliances directive.
Product: gas room heater
Model: Vejen
This appliance complies with the Gas Appliance Regulation (EU)
2016/426.
Harmonized standards applied: EN 613 2000/A1 2003.
This declaration is invalid, if without the written permission of Glen
Dimplex Benelux:
- Changes are made to the appliance.
- The re is connected to other exhaust materials than
specied.
2 Safety instructions
> Please note:
It is advisable to always install a screen for the replace if children,
elderly or disabled people are present in the same room as the
replace. If regularly vulnerable persons can be present in the
room without supervision, sufcient protection must always
be placed around the replace.
• The appliance is designed for atmospheric and heating
purposes. This means that all visible surfaces, including the
glass, can become hotter than 100 ° C. An exception to this
is the underside of the replace and the control buttons.
• Do not use the remote control and / or app outside the room
where the re is located. So that you are always aware of the
situation around the replace when it is being operated.
• The unit must be installed and subsequently serviced every
year and maintained in accordance with these instructions
and the applicable national and local regulations.
• Ensure that the data on the type label matches the local gas
type and pressure.
• The settings and the construction of the re must not be
changed!
• Do not place extra imitation wood or other smoldering
material on the burner or in the combustion chamber.
• Do not place any combustible materials within 1m of the
radiation area of the re.
• Through the natural air circulation of the re moisture and
uncured volatile components from paint, building materials
and carpeted oors, etc. are attracted. These parts can settle
as soot on cold surfaces. Therefore do not light the re
shortly after installation.
• Light the re for the rst time and run for several hours on the
highest setting, so that the paint can cure. Provide adequate
ventilation, so that any fumes can disperse; we recommend
vacating the room during this process.
> Please note:
1. All transport packaging is removed.
2. No children and pets in the room present.
3 Installation requirements
3.1 Minimum distance to combustible materials
around the re
• Keep a minimum distance of 9cm to the back wall and 50cm
at the sides.
3.2 Flue pipe and terminal requirements
• For the supply of the combustion air and the discharge of the
combustion gases you should always use the Flue materials
specied by Faber.
> Please note: Only when using these materials can Faber
guarantee the safe and proper operation of the appliance.
* This appliance must be installed in a chlorine-free
environment.
* The outside of the concentric ue material can heat up to
+/-150°C. Ensure, when penetrating a ammable wall or
ceiling, construction with proper insulation and protection.
Ensure sufcient clearance is maintained.
* Ensure that the concentric ue pipes are supported every
meter, so that the weight of the pipes is not supported by the
re.
* It is not permitted to start directly on the device with
concentric cut down pipe material.
The air supply could then possibly be closed.
3.3 Terminals
The combined supply and discharge can be done both via wall or
through the roof or through an existing chimney. Verify if the
position of the terminal meets the local regulations regarding
ventilation openings. The ue outlet can end on an external wall or
a roof.
Check whether the outlet desired by you complies with local
requirements concerning good function and ventilation systems.
> Please note:
For a proper functioning the terminal should be at least 0,5m. away
from:
• Corners of the building
• Roof overhangs and balconies
• Eaves (with the exception of the roof ridge, see Chapter 15).

Installation manual
9
3.3.1 C11, wall terminal
For a facade or wall outlet use a wall terminal (see g. 1.0 C11).
Depending on the calculation this can be a diameter of 130/200mm
or 100/150mm.
3.3.2 C31, roof terminal
For a at or pits roof outlet use a long roof outlet with a diameter of
100/150mm (see g. 1.0 C31)
3.3.3 C91, existing chimney
You can also connect to an existing replace chimney. The existing
chimney functions then as air supply and a exible stainless steel
tube drawn through the chimney carries the ue gases. The exible
stainless steel tube of Ø100mm must have a CE mark have up to
600°C.
Use the short chimney outlet. (See g. 1.0 C91).
The chimney must have the following conditions:
• The channel of the chimney must be at least 150x150mm.
• There should be no more than one device on a chimney.
• The chimney must be in good condition:
o No leakage
o Well cleaned
For more information about connections to existing chimneys, ask
the installation manual “chimney connection set”.
4 Preparation and installation
instructions
4.1 Gas connection
The gas connection must comply with the applicable local
standards. We advise using a Ø15mm gas connection directly from
the gas meter to the appliance, with a shut-off valve in the proximity
of the appliance, which must always be freely accessible. Position
the gas connection so that it is easily accessible at all times for
service and that the burner unit can be disassembled. (See g.
8.0-C and dimensional drawing 16.2 for position of the gas
connection).
4.2 Electrical connection
The power supply must comply with the applicable local standards.
A wall socket 230VAC/50Hz must be installed near the re. For
power supply make use of the included plug adapter. See g 2.0 for
the wiring diagram of this connection and the LED Symbio module.
A = Plug adapter 6V
B = Micro switch
C = Spark transformer
D = LED Symbio module
E = Slider
4.3 Preparing the re
• Remove the re from its packaging. Open the operation door
(see g. 3.0), take the packaged parts from the re and
remove the bolts in the bottom plate.
• Prepare the gas connection on the regulator. See g. 8.0-C
and dimensional drawing 16.2.
4.4 Positioning the re
Take into account the installation requirements and the minimum
distances around the replace. (See Chapter 3).
4.5 Installing the ue materials
• When penetrating a non-combustible wall or ceiling the
opening must be at least 5mm larger than the diameter of the
discharge material. At a combustible wall or ceiling is this
100mm larger than the diameter of the drainage material.
• Horizontal sections should be installed with a slope towards
the re (3 degrees).
• Build the system from the re. If this is not possible you can
make use of an extendable adapter section.
• For truing up the exhaust system use the 0,5m. pipe, which
can be shortened and ensure that the inner pipe is always
2cm longer than the outer pipe.
• Parts, which are shortened, must be secured with a
self-tapping screw.
• Wall and roof terminals can also be cut.
• Do not insulate but ventilate built-in ue material (approx.
100cm²).
5 Removing the glass
5.1 Front glass
• Remove the front frame. See g. 4.0.
• Slightly loose the screws of the glass support under.
See g. 4.1.
• Slightly loose the nuts of the upper glass support and remove
it. See g. 4.2.
• Remove the front glass. See g. 4.3.
For replacing the front glass repeat the steps in reverse
order.
> Please note:
Clean all ngerprints on the glass; otherwise they will burn in once
the re is used.
5.2 Side glasses
For cleaning only it’s not necessary to remove the side glasses.
Only remove the front glass. See Chapter 5.1.
• Remove the side panel. See g. 5.0.
• Slightly loose the screws of the glass support under.
See g. 5.1.
• Slightly loose the nuts of the upper glass support and
remove it. See g. 5.2.
• Remove the side glass. See g. 5.3.
> Please note:
Clean all ngerprints on the glass; otherwise they will burn in once
the re is used.

Installation manual
10
6 Placing the decoration material
It is not permitted to use other or to add more material in the
combustion chamber.
Keep the pilot light always free of decoration material!
• Place the glass plate on the bottom in the recesses on the
left and right. See g. 6.0a and b.
• Spread the glass fragments over the glass panel (one layer)
and cover these with the supplied vermiculite grains.
(The amount of vermiculite affects the intensity of the glow
effect and can be done according to your own discretion).
• Place the imitation logs. Make sure that the logs are properly
connected to the tube burners and rest on the bottom of the
re.
If necessary remove glass fragments and/or vermiculite
underneath the burners. (See the supplied log set instruction
card).
• Spread the rest of the vermiculite and the chips over the
bottom of the burning chamber. Ensure that the air openings
are not covered.
Start the re as described in the user manual. Check the appearan-
ce of the ames and for burning against the vermiculite grains.
7 Checking the installation
7.1 Checking the ignition of pilot light and
main burner
Light the re as described in the user manual.
• Check that the pilot ame is not covered by chips and/or an
imitation log.
• Check the ignition of the main burner on full and low setting.
(ignition must be smooth and quiet).
7.2 Checking for gas leaks
Check with a gas leak nder or spray all connections and pipes for
gas leakage.
7.3 Checking the burner pressure and
primary pressure
Check that the burner pressure and primary pressure match with
the information listed in the manual. See Chapter 14.
Measuring the primary pressure:
• Close the shut-off valve.
• Turn measuring nipple A (see g. 8.0) some few turns open
and connect a measuring hose to the gas regulator.
• Take this measurement at highest setting of the re and when
the re is set to pilot light.
Do not connect the unit if the pressure is too high.
Measuring the burner pressure:
Check the burner pressure only with proper primary pressure!
• Turn measuring nipple B (see g. 8.0) some few turns open
and connect a measuring hose to the gas regulator.
• The pressure must correspond to the value indicated in the
technical specications of this manual. In case of deviation
contact the manufacturer.
> Please note:
Close all pressure measuring nipples and check for gas leakage.
7.4 Checking the ame image
Let the re burn for at least 20 minutes at highest setting and check
the ame for:
• Flame distribution
• Color of the ames
If one or both points are not acceptable then check:
• The log set layout and/or the amount of glass granulate/chips
on the bottom plate.
• The pipe connections for leaks (in case of blue ames).
• Whether the correct ue restrictor is tted. See g. 9.0.
• The outlet.
o Wall terminal right side up
o Roof terminal on the right position
o If the maximum horizontal ue lengths is not exceeded.
8 Instructions for the client
• Recommend that the unit should be checked annually by a
qualied specialist to ensure the safe use and to guarantee a
long service life.
• Give advice and instructions on care and cleaning of the
glass. Highlight the danger of burnt-in ngerprints.
• Instruct the customer on the operation of the appliance.
• Hand over to customer:
o Installation manual
o User manual
o Log set instruction card
9 Annual maintenance
9.1 Checking and cleaning
• Check and clean if necessary after verication:
o the pilot light
o the combustion chamber
o the glass
o the logs for breakage
o the outlet
o the wiring/contacts for corrosion
• Replace, if necessary:
o chips/vermiculite
o Glass granulate
9.2 Cleaning the glass
Most deposits can be removed with a dry cloth. Clean the glass
with Faber glass polish..
> Please note:
Avoid ngerprints on the glass. These are no longer removable
after they are burnt in!
Now carry out check-up as described in Chapter 7.
10 Conversion to other gas type
Conversion to another type of gas can only be carried out by a
qualied installer / dealer.
To do so, please contact your dealer.
Specify with your order always the type and serial number of the
device.

Installation manual
11
11 Flue calculation
A simple way to calculate whether the exhaust conguration is
possible in combination with your re, use the free “Faber Flue App”
and download it from:
INTERNET:
BlackBerry, Android and PC (Microsoft store).
APP store:
iPhone, iPad and Mac.
Google Play:
Android smartphones and Android tablets.
Alternatively use the exhaust calculation table (see chapter 13).
The alternatives of outlet lengths and any restrictors are set out in
the restrictor table. In the table we work with start length (STL), total
vertical height (TVH) and total horizontal length (THL).
• Start length (STL):
This is the rst part that is placed on the re and represents a
certain value (g. 12.1, 12.2 and 12.3 A, N and F). This value is in
the top row of the table (see restrictor table 11.1 and 11.2).
• Total vertical height (TVH):
TVH is the difference in height measured from the top of the unit to
the outlet; it can be measured or determined from the building plan.
For clarication see the TVH indication in the drawings (g. 12.1,
12.2 and 12.3).
• Total horizontal length (THL):
THL is the total horizontal length and consists of elbows and pipes
which are entirely in the horizontal plane. Elbows I, K and Q and
the elements H, J, L, M, P and R (g. 12.1 and 12.2).
• Length horizontal plane:
The horizontal length consists of the elements H, J, L, M, P and R
(g. 12.1 and 12.2).
• Elbows 90° in the horizontal plane:
Horizontal bends are bends which are entirely in the horizontal
plane (g. 12.1, 12.2 and 12.3 I, K and Q).
• Bends 45° or 30° in the horizontal plane:
Horizontal bends are bends which are entirely in the horizontal
plane.
• Elbows 90° vertical to horizontal plane:
These are 90° elbows, which proceed from horizontal to vertical
(g. 12.2 and 12.3 G, O and S).
• Bends 45° or 30 °vertical to horizontal plane:
These are 30° or 45° bends with a vertical offset of less than 45°
(g.12.1 B and D).
• Pipes under a tilt angle:
These are pipes which are vertically ascending at an angle of 30°
or 45° (g. 12.1 C). Fill in only in combination with at least 2x 30 or
45° bends in the vertical part.
• Restrictor table:
See the restrictor table at the right vertical (TVH) and
horizontal length (THL). For “x” and if the values are outside the
table, then the combination
is not allowed. Only then adjust the TVH or THL.
If a value is indicated, check that the calculated STL value is not
lower than indicated in the table. In this case STL must be adjusted.
The found value indicates the width of the restrictor (“0” means no
restrictor). Standard is a restrictor of 30mm installed (see g. 9.0).
> Please note:
When vertical ue length only, an “air restrictor” must be placed.
(See g.10.0a to 10.0e). This “air restrictor” comes standard with
the device.

Installation manual
12
0,2 0,5 111 1 1
012345678910
0xxxxxxxxxxx
0,5 xxxxxxxxxxx
130,10 30 0xxxxxxxx
1,5 30,10 30 30 0 0 x x x x x x
240,10 40 30 30 0 0 0 x x x x
340,10 40 40 30 30 0 0 x x x x
450,10 40 40 40 30 0 0 x x x x
550,10 50 40 40 30 30 0 x x x x
650,10 50 50 40 30 30 30 x x x x
760,10 50 50 50 30 30 30 x x x x
860,10 60 50 50 30 30 0 x x x x
960,10 60 50 50 30 30 0 x x x x
10 60,10 60 50 40 30 0 0 x x x x
11 65,10 60 50 40 30 0 0 x x x x
12 65,10 60 50 40 30 0 0 x x x x
13 65,10 60 50 40 30 0 0 x x x x
14 65,10 60 50 40 30 0 0 x x x x
15
65,10 60 50 40 30 0 0 x x x x
16 65,10 60 50 40 30 0 0 x x x x
17 65,10 60 50 40 30 0 0 x x x x
18 65,10 60 50 40 30 0 0 x x x x
19 65,10 60 50 40 30 0 0 x x x x
20 65,10 60 50 40 30 0 0 x x x x
21 65,10 60 50 40 30 0 0 x x x x
22 65,10 60 50 40 30 0 0 x x x x
23
65,10 60 50 40 30 0 0 x x x x
24 65,10 60 50 40 30 0 0 x x x x
25 65,10 60 50 40 30 0 x x x x x
26 65,10 60 50 40 30 xxxxxx
27 65,10 60 50 40 xxxxxxx
28 65,10 60 50 xxxxxxxx
29 65,10 60 xxxxxxxxx
30 65,10 x x x x x x x x x x
STL
THL
TVH
11.1 Restrictor table Vejen
Starting length (STL), vertical (TVH) and horizontal (THL).

Installation manual
13
Fig. 12.1 Fig. 12.2
fig. 12.1 fig.12.2
fig. 12.3
Fig. 12.3
12 Examples ue materials

Installation manual
14
Value
0,2
0,5
1
1,5
2
0,1
0,2
1
0
……………………..
rounded value
……………. meter
Part number xvalue result
Total Length in meters ……… x1……………..
90° Bend, vertical to
horizontal
……… x0,4 ……………..
45° Bend, vertical to
horizontal
……… x0,2 ……………..
90° Bend in horizontal
direction
……… x1,5 ……………..
45° Bend in horizontal
direction
……… x1……………..
flue pipes at an angle
in meters
……… x0,7 ……………..
……………+ ………………….. meter
Value
Starter length (STL)
First part on top of the appliance
Flue length from 0,1m till 0,45m
Flue length from 0,5m till 0,90m
Flue length from 1m till 1,4m
Flue length from 1,5m till 2m
Flue length 2m or more
Bend 90°
Bend 45°, 30° or 15°
Roof terminal
Wall terminal
Calculation
Total
rounded value
Total Vertical Height (TVH)
measured height
…………………………………………………… meter
Total Horizontal Length (THL)
13 Calculation sheet

Installation manual
15
found value
………………………………
………………….. mm
mark
Install the air restrictor plate, see installation manual 0,1
Install adapter 100/150 direct on top of the fire 0,2
In case of wall terminal, install adapter 100/150 before the last
bend, incase of roof terminal just before the terminal. 0,3
In case of roof terminal (always size 100/150) install the 100/150
adapter just before the terminal. Wall
terminal 130/200
0,4
From the fire first an adjuster to 130/200 and 1 meter 130/200,
after that reduce to 100/150 and everything 100/150. 0,5
Restrictor size = Value for the comma
Extra information = Value behind the comma
Search in the table at TVH and THL and enter the value that is found.
If the detected value is a number, check whether the completed STL is higher or equal to the value in the table.
Is the STL value lower as specified in the table then the installation is not possible.
Solution: Start length to low, see for the minimum length in the top row of the table.
Is the found value X, then the installation is not possible.
Solution: Change the TVH or THL.
Results

Installation manual
16
Symbol Unit
Reference gas/inlet pressure G20-20 G30-30 G31-37 mbar
Emissions in space heating NOx 102 123 128 mg/kWhinput (GVC)
Direct heating output
Nominal heat output Pnom 5,8 5,8 5,8 kW
Minimum heat output (indicative) Pmin 2,8 2,8 2,8 kW
Useful efficiency (NCV)
At nominal heat output ꞃth,nom 91,2 91,2 91,2 %
At minimum heat output (indicative) ꞃth,min 87,3 87,3 87,3 %
Appliance input data
Input Hi 6,4 6,4 6,4 kW
0,689 0,203 0,258 m³/h
00,484524 kg/h
Burner pressure at full mark 16,6 29,1 35,8 mbar
Power requirement for permanent pilot light
Additional electricity consumption
At nominal heat output elmax 0 0 0 kW
At minimum heat output elmin 0 0 0 kW
In standby mode elSB 0 0 0 kW
Energy-efficiency
Energy-efficiency class B B B
Energy-efficiency index EEI 82 82 82
Type heating output/control room temperature
yes
no
no
no
no
no
Glen Dimplex Benelux Saturnus 8 Heerenveen The Netherlands
With mechanical control of the room temperature by thermostat Control of room temperature, with open
window detection no
With electronic control of the room temperature
With electronic control of the room temperature plus day-time
switch
With optional remote control no
With electronic control of the room temperature plus week-time
switch
0 0 kW
Other control options
One step heat output, no control of room temperature Control of room temperature, with
presence detection no
Two or more manually adjustable stages, no control of room
temperature
0
Gas rate at full mark
Power requirement for permanent pilot light (if
applicable) Ppilot
Gas connection 3/8"
Indirect heating functionality no
Category II2H3+, II2H3P
Diameter outlet/inlet 100/150
Technical data
Type indication(s) Vejen
Type appliance C11/C31/C91
14 Technical data

Installation manual
17
15 Terminal position
Location Position outlet Distance mm
D Under a gutter 500
E Under a roof edge 500
F Under a carport or balcony 500
G Vertical downpipe 300
H Inside and outside corners 500
J From wall surface to a wall outlet 1000
K Two gable outlets against over each other 1000
L Distance between two roof outlets 450
M Two roof outlets above each other on a pitched roof 1000
N Two gable outlets next to each other 1000
Short roof terminal.
Only for existing
Chimney connection
Extension pipe over roof
> Please note:
These rules apply only for the proper functioning of the unit,
for ventilation and environmental protection you need to comply
with the applicable rules as dened in the building regulations.

Installation manual
18
16 Dimensional drawings
16.1 Vejen

Installation manual
19
16.2 Position gas connection

20
Dealerinfo:
www.faber-res.eu info@faber-res.eu
Saturnus 8 NL - 8448 CC Heerenveen
Postbus 219 NL - 8440 AE Heerenveen