Faber e-MatriX 800-I User manual

40011677-1839 Manual e-MatriX 800-I/II/III ENG
Manual e-MatriX 800-I/II/III ENG

2
Manual e-MatriX 800
Registration plate:

Manual e-MatriX 800
3
1.0
1.1
1.2a 1.2b

4
Manual e-MatriX 800
2.0c
2.1a
2.0b
2.1b
2.0a

5
Manual e-MatriX 800
2.1c
3.0
2.2
3.1
4.0 4.2 4.3
4.1

Manual e-MatriX 800
6
5.0

Manual e-MatriX 800
7
6.0
7.0 7.1
7.2
7.3
7.4 8.0

Manual e-MatriX 800
8
1 General
1.1 Introduction
 Onlyhavethereinstalledbyaqualiedinstalleraccordingtothewaterandelectricsafety 
 regulations.Readthisinstallationmanualproperly.
1.2 Check
 • Beforeinstallation,checktherefortransportdamageandreportimmediatelytoyoursupplier.
 • Checkwhetherallofthepartsbelowareincluded:
  o Controlbox
  o Remote
  o Decorationmaterial
  o Suctioncups(2x)
  o Servicedoor
  o Sparetransducers(2x)andsponge
1.3 CE declaration
 Product:electricreOpti-myst
 Model:e-MatriX800x500-I/II/IIIande-MatriX800x650-I/II/III
 TheproductcomplieswiththeEuropeanSafetyStandardsEN60335-2-30andtheEuropean 
 StandardElectromagneticCompatibility(EMC)EN55014,EN60555-2andEN60555-3thesecoverthe
 essentialrequirementsofEECDirectives2006/95/ECand2004/108/EC.
 !!Thisdeclarationisinvalidifchangesaremadetothere.
2 Safety instructions
 • Donotuseoutdoors.
 • Donotuseintheimmediatesurroundingsofabath,showerorswimmingpool.
 • Donotusewithouttheglassinstalledinplace.
 • Theremustbeinstalledaccordingthismanual.
3 Installation requirements
3.1 Water supply
 • Waterconnection½”or¾”placedatanaccessiblelocation.
 • Waterpressureontherebetween0,5and8Bar.Whererequired,useapressure
  reducingvalve.
3.2 Power supply
 • Electricconnection-230VAC/50Hzearthedandplacedatanaccessiblelocation.
4 Installation instructions
4.1 Preparingthere
 • Ensurethatallpackingitemsareremoved.
 • Removethetransportscrewonthefrontseeg.1.0.
 • RemovethefrontglassandstoreitatasafeplaceseeChapter5.
 • RemovethefuelbedandstoreitatasafeplaceseeChapter6.

Manual e-MatriX 800
9
4.2 Placingthere
 Foraproperfunctioningofthere,alwaysensurethatthereislevelled.
 Usetheadjustablefeetorthedistanceholderatthebacksideofthere.Seeg.1.2a..
4.2.1 Floor standing
  Placethereattherightpositionandxitonthewallseeg.1.1.
4.2.2 Hanging on the wall
  Therecanbehangingonthewallwiththeoptionalwallbracketseeg.1.2a,1.2band 
  dimensionaldrawinginChapter13.6.
4.3 4.3Installationandnishing(seeg.1.0)
4.3.1 With cover strip “A”
  BuildthefalsechimneybreastorplateauagainstdistanceholderB.
4.3.2 Without cover strip “A”
RemovedistanceholdersBfromthere.Buildthefalsechimneybreastorplateauagainst 
  distanceholderC.
4.4 Controlbox(seeg.4.0)
 !!FixtheControlboxatanaccessiblelocationbehindtheservicedoor.SeeChapter13.5and13.7.
4.4.1 Electric connection
 • UsethesuppliedextensioncabletoconnecttheControlboxtotheEngineseeg.4.0-B.
 • LeadtheDCcable,insidetheEngine,totheControlboxandconnectitseeg.4.0-A.
  -Max.cablelengthfromthecenteroftheretotheleft1,5m.
  -Max.cablelengthfromthecenteroftheretotheright1,0m.
 • Connectthesuppliedmainsleadseeg4.0-C.
 Ifdesired,a2mextensionsetisavailable.
4.4.2 Water connection
 Thisapplianceisequippedwiththefollowingoverowprotections:
  o ElectromechanicalvalveintheControlboxwhichissentbyanoverowsensorinthe
   watertank.
  o AbsorptionvalveintheEnginethatkicksinwhenthewatersumphasanunexpectedly
   overowseeg.5.0-K.
 • Connectallpartsaccordingowdiagramseeg.5.0.
  A=mainswater  F=meshlter 1=safetyclips(11x)
  B=½or¾”connector G=in-linelter 2=in-linelterbrackets(2x)
  C=¼”1mpipe  H=controlbox 3=elbows(4x)
  D=ballvalve  I=¼”1,5mpipe
  E=tobecutfrom¼”1mpipe J=e-MatriXEngine
 • Placethewaterltersatanaccessiblelocationincorrectalignment,there’sa“ow”direction
  markingonbothltersandControlbox.Seeg.4.0.
 !!CarryoutaperformancetestseeChapter9andcheckallconnectionsforwaterleakagebefore 
 placingthefuelbedandfrontglass.

Manual e-MatriX 800
10
4.5 Build-in structure
 • Thee-MatriXneedsaminimumventilationof50cm²aboveand210cm²underneaththere.
 • Theconstructionmaynotrestonthere.
 • Thee-MatriXneedsaminimumfreespaceof50mmabovethere.
5 Removing glass
5.1 Frontglass(e-MatriXfrontglassonly)
 • Removethecoverstripseeg.2.0a.
 • Rotatetheglassclampclockwiseseeg.2.0b.
 • Placesuctioncupsandremovethefrontglassseeg.2.0c.
5.2 Frontglass(e-MatriX2or3sidedglass)
 • Rotatetheglassclampclockwiseseeg.2.1aand2.1b.
 • Placesuctioncupsandremovethefrontglassseeg.2.1c.
 Forreplacingthefrontglassrepeatthestepsinreverseorder.
5.3 Side glass
 Forcleaningonlyit’snotnecessarytoremovethesideglass.
 • FirstremovethefrontglassseeChapter5.1or5.2.
 • Placeasuctioncupandremovethesideglassseeg.2.2.
 Forreplacingtheglassesrepeatthestepsinreverseorder.
6 Removing fuel bed
!!Neverliftupthefuelbedwithoutusingthesuppliedhandles.
 !!Keepthesehandlesforfutureuse.
 • RemovethefrontglassseeChapter5.1or5.2.
 • Covertheframetoavoidscratchesseeg.3.1-A.
 • Screwthehandlesinthefuelbedseeg.3.0.
 • Liftupthefuelbedcarefully,disconnecttheplugandstoreitatasafeplaceseeg.3.1.
 Forreplacingthefuelbedrepeatthestepsinreverseorder!
7 Placing decoration material
!!Keepdecorationmaterialawayfromchildren,personswithreducedphysicalormentalcapabilities
 andanimals.
 !!Don’tplacedecorationmaterialinthecenterareaseeg.6.0.
 Thesuppliedarticialashandchipscanbeusedtopersonalizeyourre!

Manual e-MatriX 800
11
8 Usingthere
8.1 Manualcontrol-behindaccessdoor(seeg.4.1)
 A=mainswitch       
 1=ON/OFF    
 2=pairing     
 3=onlyformaintenance(serviceengineer) 
 4=reduceame
 5=increaseame
 6=reducerecracklingsound
 7=increaserecracklingsound
8.2 Remotecontrol(seeg.4.2) 
 1=OFF
 2=pressonceforON/presstwiceforgloweffectonly
 3=reduceame
 4=increaseame
 5=reducerecracklingsound
 6=increaserecracklingsound
8.2.1 Pairing the Bluetooth remote
 AttheControlboxseeg.4.1:
 • TurnthemainswitchintheONposition,1beep.
 • Pressthe button,1beepandtherewillbegintostart.
 • Pressthe button,therestartstobeepandtheLED’swillstarttoblinkonandoff.
 • Pressabuttonontheremotecontrol.Therewillswitchoff.Nowtheremotecontrolispairedto
  there.
8.3 Firsttimewaterll
 • Ensurethatallballvalvesareopenandturnonthewatersupply.
 • SwitchthereonbypressingthemainsswitchtotheONpositionandpressingthe button
  seeChapter8.1and8.2.
  o Ifthewaterlevelishighenoughtheameswillautomaticallystartafter45seconds.
  o Ifthewaterlevelisn’thighenoughtheLED’scontinuouslytoblinktwiceafter45seconds.
   PressthemainsswitchtotheOFFposition,wait5secondsandrepeatthesecondstep
   above(thisprocesscanbeneededseveraltimes).
8.4 Gettingthedesiredameeffect
 • Therealwaysstartswithminimumamesetting.Whendesiredpressthebuttonforhigher
  ames.Pleasegivetheamegeneratortimetoreacttothechangesyoumake.
  !!Increasingtheameheightcanleadtocondensationontheglass.
 • Pressthe and buttonforthevolumeofthecracklingsoundtoyourdesiredlevel.
  Theminimumvolumeofthissoundisoff.
Ifthereiseitherturnedtostandbyorswitchedoffentirely,itwillalwaysreverttotheminimumamesetting.
Thesoundlevelwillremainthesameasthelastsoundlevelassetbytheuser.

Manual e-MatriX 800
12
9 Performance test
 • Firsttimewaterll,seeChapter8.3.
 • Checkallconnectionsforwaterleakage.
 • Checkifthefan,mountedatthetopinsidethere,isrunning.
 • Checkiftheremotecontrolisfunctioningatthedesireddistance(max.8m)
  o Ifneeded,movethereceivertoadifferentpositionin-oroutsidetheconstruction(seeg.4.3).
   ThereceiverisplacedatthebackinsidetheEngineandhasacablelengthof1,4m.
 • ReplacefuelbedseeChapter6.
 • ReplacefrontglassseeChapter5.1or5.2.
 • Performanalfunctionalcheck.
10 Maintenance
10.1 Maintenancefrequency
 • Cleaningwatersump,airlterandreplacingtransducers.
  Commercialuse:everythreemonths.
  Domesticuse:onceayear.
 • Cleaningmeshlterandreplacingin-linelter.
  Commercialuse:onceayear.
  Domesticuse:everysecondyear.
 !!Themaintenanceintervaldependsonthewaterqualityand/ortherunninghoursandthereforecan
 differfromtheabovementioned.
 10.1.1Cleaningwatersump
 !!AlwayspressthemainsswitchtotheOFFpositionanddisconnectthepowersupplyseeg.4.1.
 !!Neveruseabrasivecleaners.
 • RemovethefrontglassseeChapter5.1or5.2.
 • RemovethefuelbedseeChapter6.
 • Disconnectthe‘llcap’byturningitclockwiseseeg.5.0-Land7.0.
 • Disconnectthe2connectors,locatedontherightsideofthewatersumpseeg.7.1.
 • Releasethe2clipsonbothsidesandremovethenozzleseeg.7.2and7.3.
 • Gentlyliftupthewatersumpwithoutspillinganywaterseeg.7.4.
 • Removethetransducersandemptythewatersump.
 • Putasmallamountofwashingupliquidintothesump,andusingasoftbrushtocleanthe 
  sump.Alsocleanthetransducers,includingthediscsunderneaththecone.Removethecone
  byturningitclockwise.
 • Whencleaned,thoroughlyrinsethewatersumpwithcleanwatertoremovealltracesof 
  washingupliquid.
 • Cleanthenozzlewiththeasoftbrushandushoutthoroughlywithwater.
 • Reversethestepsabovetoreassemble.

Manual e-MatriX 800
13
 10.1.2Cleaningairlter
 • Gentlyslidetheairlterupwardsoutofitsplasticholderseeg.8.0.
 • Gentlyrinsewithwaterinthesinkanddrywithfabrictowelbeforereturning.
 • Replacetheltermakingsurethatthecoarseblacklterisfacingthebackofthere.
 • PlacethefuelbedseeChapter6.
 • PlacethefrontglassseeChapter5.1or5.2.
 10.1.3Replacingtransducers
 !!AlwayspressthemainsswitchoftheControlboxtotheOFFposition(seeg.4.1)anddisconnect
 thepowersupply.
 Thetransducersarexedinthewatersumpwithplasticclips.
 • Followtherst5stepsinChapter10.1.1togainaccesstothetransducers.
 • Presstheclipbackandliftthetransducerupwardsoutofitsholder.
 • Placethenewtransducersandrepeatthestepsaboveinreverseorder.
  (Pleasetakenotethatthetransducerswillnotblocktheopeningofthecones).
 10.1.4Cleaningmeshlter
 • Turnoffthewatersupply.
 • Closetheballvalves.
 • Unscrewthebaseandcleanthelterinside.
 10.1.5Replacingin-linelter
 • Turnoffthewatersupply.
 • Closetheballvalves.
 • Replacethein-linelter.
 (Placeitincorrectalignment,there’sa“ow”directionmarkingonthelter).
10.2 Resettingabsorptionvalve(seeg.5.0-K)
 Whentheabsorptionvalveisactivated,thespongeneedtobereplaced.
 TheabsorptionvalveislocatedontherightfrontsideatthebottomoftheEngine.
 • Takeouttheactivatedsponge.
 • FixthecauseofthewaterleakageandremoveanywateratthebottomoftheEngine.
  Placethenewspongeandopentheabsorptionvalvebypressingdownthewhiteclamp.

Manual e-MatriX 800
14
11 Technical data
12 Trouble shooting
Watts W 250
Volts V 230-240
Batteries remote V (2x) 1,5 AA
Water consumption l/h 0,15
Inlet water pressure Bar 0,5-8
Water connection Inch ½ or ¾
Symptom Cause Action
Mains plug is not plugged in.
Check plug is connected to wall socket
correctly.
See Chapter 8.3.
Low water level.
Check that the connector(s) is inserted
correctly see fig. 7.0.
The transducers) are not connected
properly.
Low water level. See Chapter 8.3.
Switch the mains switch of the Control box to
the OFF position.
Check all connections on water leakage.
Check that the ball valves are open.
The absorption valve is activated See Chapter 10.3.
e-MatriX will not operate, the LED’s
continuously to blink once every eight
seconds.
Water level too high.
Check the electromechanical valve in the
Control box.
Switch the mains switch of the Control box to
the OFF position and heck all connections on
water leakage.
Close the ball valves and check the mesh filter,
by unscrewing the base of it to see that it is not
clogged with dirt and debris.
The flame effect is too low on the highest
setting.
The transducers and/or air filter are dirty. Call for maintenance.
The flame effect is too high and there is too
much smoke.
The extract fan doesn’t work anymore.
Check if the fan, mounted at the top inside the
fire, is running.
Low batteries. Place new batteries.
Remote isn’t paired to receiver. See Chapter 8.2.1.
Distance to fire too big See Chapter 9 (remote control).
The flame effect will not start.
e-MatriX will not start or stopped working and
the LED’s continuously to blink twice.
e-MatriX will not operate, the LED’s
continuously to blink four times.
Water filling time is too long.
Remote is not working.

Manual e-MatriX 800
15
13 Dimensional Drawings
13.1 e-MatriX800x500/650-I

Manual e-MatriX 800
16
13.2 e-MatriX800x500/650-IIL

Manual e-MatriX 800
17
13.3 e-MatriX800x500/650-IIR

Manual e-MatriX 800
18
13.4 e-MatriX800x500/650-III

Manual e-MatriX 800
19
13.5 Control box

Manual e-MatriX 800
20
13.6 Wall bracket