Facility Explorer FX Series User manual

Installation Instructions
Issue Date April 9, 2014
© 2014 Johnson Controls, Inc. 1
Part No. 24-10174-26, Rev. B www.johnsoncontrols.com
FX Supervisory Controllers Modem Card
Installation Instructions
Application
The modem option card (Figure 1) provides 56 Kbps
auto-dial/auto-answer modem communications
capability to the FX Supervisory Controllers.
FIG:Mdm
Figure 1: FX Supervisory Controllers Modem Card
For the FX20/FX60 Supervisory Controllers, the
modem option card must be installed in Option Slot 1;
and when installed, the modem card disables the
onboard RS-232 port on FX20/FX60 Supervisory
Controllers. For the FX70 Supervisory Controllers, the
modem option card must be installed in Option Slot 1
or Option Slot 2; and when installed, it does not
disable the onboard RS-232 port. FX22/FX62
Supervisory Controllers only have one option card slot;
and when installed, the modem option card disables
the onboard RS-232 port. The modem option card is
not supported in any FX Supervisory Controller
already fitted with a GPRS modem card.
For related information on FX Supervisory Controllers
mounting and wiring, refer to the FX Supervisory
Controllers Installation Instructions
(Part No. 24-10174-77).
North American Emissions Compliance
United States
This equipment has been tested and found to
comply with the limits for a Class A digital device
pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable
protection against harmful interference when this
equipment is operated in a commercial
environment. This equipment generates, uses,
and can radiate radio frequency energy and, if
not installed and used in accordance with the
instruction manual, may cause harmful
interference to radio communications. Operation
of this equipment in a residential area is likely to
cause harmful interference, in which case the
user will be required to correct the interference at
his/her own expense.
Canada
This Class (A) digital apparatus meets all the
requirements of the Canadian Interference-
Causing Equipment Regulations.
Cet appareil numérique de la Classe (A) respecte
toutes les exigences du Règlement sur le
matériel brouilleur du Canada.
Installation
Parts Included
Unpack the modem option card and inspect the
contents of the package for damaged or missing
components. If damaged, notify the appropriate carrier
and return any damaged components for repair or
replacement.

2FX20/FX60 Modem Card Installation Instructions
Included in this package are the following items:
one modem option card and connector end plate
FX Supervisory Controllers Modem Card
Installation Instructions (Part No. 24-10174-26)
Special Tools Needed
The following tool is required for installation:
#2 Phillips screwdriver: used to install the modem
card
Safety Precautions
The following information relates to the installation and
startup of the modem option card.
!
WARNING: Risk of Electric Shock.
Disconnect power supply before making electrical
connections. Contact with components carrying
hazardous voltage can cause electric shock and
may result in severe personal injury or death.
AVERTISSEMENT: Risque de décharge
électrique Débrancher l'alimentation avant de
réaliser tout branchement électrique. Tout contact
avec des composants conducteurs de tensions
dangereuses risque d'entraîner une décharge
électrique et de provoquer des blessures graves,
voire mortelles
IMPORTANT: Be careful to plug any option card
into its connector properly (pins aligned).
IMPORTANT: Avoid hot plug-in or removal of any
option card from the FX Supervisory Controller; that
is, do not remove any card with power applied. If the
unit switches to battery operation, wait for all Light
Emitting Diodes (LEDs) to go out.
Mounting
For the FX20/FX60, the modem option card must be
mounted in Option Slot 1. If another option card
already exists in Option Slot 1, move it to Option Slot
2. For the FX70, the modem option card may be
mounted into either Option Slot 1 or Option Slot 2.
Follow these instructions to mount the modem card:
1. Remove power from FX Supervisory Controller.
2. Remove the FX Supervisory Controller cover
(FX20/FX60/FX70) or covers (FX22/FX62). For
the FX20/FX60/FX70, press in the four tabs on
both ends of the cover and lift off. For the
FX22/FX62, first remove the right cover, then the
left cover, retaining the two screws that secure
each cover (Figure 2).
Option Card Slots
Figure 2: FX22/FX62 Option Card Slot
Note: If accessory modules are plugged into the
FX20/FX60/FX70 Supervisory Controller, you may
need to slide them away from the unit to access the
cover tabs.
3. For the FX20/FX60/FX70, remove the battery and
bracket assembly by taking out the four screws
holding it in place. Set the screws aside for later.
4. Unplug the battery from the connector on the
FX20/FX60/FX70 Supervisory Controller (see
Figure 3).
FIG:RmvBatt
Battery Assembly
(includes cable and
bracket)
Blanking
End Plate Option Slot 1
Area
Option Slot 2
Area
Screws(4)
FX20/FX60
You must install the
Modem in this Slot.
Unplug battery here.

FX20/FX60 Modem Card Installation Instructions 3
Figure 3: Removing Battery Assembly
5. For the FX20/FX60/FX70 controller, remove the
Option Slot blanking end plate. Retain the
blanking end plate in case you need to remove
the option card at a later date.
6. Carefully insert the pins of the modem card into
the Option Slot socket. The mounting holes on
the modem card should line up with the standoffs
on the FX Supervisory Controller. If they do not,
the connector is not properly aligned. Press until
the modem card is completely seated.
7. Place the custom end plate that came with the
modem card over its connector (see Figure 4).
FIG :I nsrt LN
Insert Modem card
into option card slot
carefully with pins aligned.
Fully sea t c ar d.
Place Modem custom
end plate over end.
FX Supervisory Controller
Battery Connector
Figure 4: Inserting Modem Card
8. For the FX20/FX60/FX70 controller, plug the
battery cable into the battery connector on the FX
Supervisory Controller (see Figure 4 for location).
9. For the FX20/FX60/FX70 controller, set the
battery and bracket assembly back over the
option card slots, with the mounting holes aligned
with the standoffs.
10. For the FX20/FX60/FX70 controller, place the
four screws through the battery bracket, through
the end plates, and into the standoffs on the FX
Supervisory Controller (Figure 5).
Hand-tighten these screws with a screwdriver.
FIG:FasnScrws
Lightly tighten the
four screws into the
standoffs by going
through the battery
bracket and end plates.
Mode Jumper
Location
Figure 5: Refastening Screws
11. Replace the FX Supervisory Controller cover or
covers. If accessory modules were unplugged,
plug them back into the FX Supervisory Controller
as before, and secure (Error! Reference source
not found.).

4FX20/FX60 Modem Card Installation Instructions
Wiring
Connect a standard RJ-11 telephone cable to the
connector on the modem card, and the other end to a
working Public Switched Telephone Network (PSTN)
dial-up telephone receptacle.
Operation
LED
A single LED is visible on the top of the modem option
card. To see it, remove the cover from the FX
Supervisory Controller. The LED operates as follows:
ACTIVE (green): When lit, the modem is
connected to another modem (a carrier signal is
detected). When ACTIVE is lit, the FX Supervisory
Controller serial port LEDs (on the lower base
board) indicate transmit and receive activity.
Serial Shell Notes
If a modem option card is installed, and you move the
FX Supervisory Controller’s mode jumper to the Serial
Shell position (see Figure 5), the FX Supervisory
Controller’s onboard RS-232 port becomes active
immediately following a reboot. This allows an RS-232
connection to the serial shell for debugging purposes.
For the FX20/FX22/FX60/FX62, the modem card is
inoperative during this period. The modem card in an
FX70 remains operational during this period.
To re-enable the modem, reposition the mode jumper
to the Normal position, and reboot the FX Supervisory
Controller.
COM Port Assignments
The modem card’s COM port assignment and location
depends on the model of FX Supervisory Controller.
Table 1 describes the COM Assignments.
Table 1: COM Assignments for Modem Card
Supervisory Controller COM Assignment
FX20/FX60 Option Slot 1 COM1 (disables onboard
RS-232 port)
FX70 Option Slot 1 COM3
FX70 Option Slot 2 COM4
FX22/FX62 COM1 (disables onboard
RS-232 port)
Repair Information
If the modem option card fails to operate within its
specifications, replace the unit. For a replacement
option card, contact the nearest Johnson Controls®
representative.
Building Efficiency
507 E. Michigan Street, Milwaukee, WI 53202
Johnson Controls® is a registered trademark of Johnson Controls, Inc.
All other marks herein are the marks of their respective owners. © 2014 Johnson Controls, Inc.