Dwyer Instruments Mercoid EDA series Installation and operating instructions

Bulletin IN-EDAW
Series EDA Electronic Pressure Controller
Specifications - Installation and Operating Instructions
DWYER INSTRU ENTS, INC. Phone: [phone] www.dwyer-inst.com
P.O. BOX 373 • ICHIGAN CITY, IN 46360, U.S.A. Fax: [phone] e-mail: [email protected]
Remote Site Products - 1-888-532-2706 - www.remotesiteproducts.com
http://www.remotesiteproducts.com/p-14331-Dwyer-Mercoid-EDAW-N1E1-09T0-Pressure-Controller.aspx

CONTENTS
Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
Model Chart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
Installation Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4 – 5
Unpacking and Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
Electrical Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
Operating Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6 - 18
Front Panel Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
Set Points & Alarms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7 - 8
Alternation (Lead/Lag) Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
Programming Chart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9 - 11
Main Menu Selections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
Menus and Values . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12 - 18
Security Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
Operation Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
Output Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14 – 15
Display Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
Advanced Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
Test Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17
Failsafe Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17
Diagnostic Error Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18
Warranty Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18
Remote Site Products - 1-888-532-2706 - www.remotesiteproducts.com
http://www.remotesiteproducts.com/p-14331-Dwyer-Mercoid-EDAW-N1E1-09T0-Pressure-Controller.aspx

1
Dimensions
1/4 MALE NPT
WITH 3/4 [19.05]
WRENCHING HEX 9/32 [7.14]
Ø 5
[127.00] Ø 4-17/32
[115.09]
1
[25.40]
3-1/16
[77.89]
27/32
[21.43]
1-59/64 [26.16] 2X 5/16 [7.93]
3-15/32 [88.11]
1-5/8 [41.28]
[40.88]
3X 1/8 [3.18]
1/2 FEMALE NPT
CONDUIT ENTRY
Remote Site Products - 1-888-532-2706 - www.remotesiteproducts.com
http://www.remotesiteproducts.com/p-14331-Dwyer-Mercoid-EDAW-N1E1-09T0-Pressure-Controller.aspx

2
SPECIFICATIONS
Service: Compatible liquids and gases.
Wetted aterials: 316L SS.
Housing: lass filled plastic.
Accuracy: ±1% of F.S. including linearity, hysteresis, and repeatability (indicator and transmitter).
Stability: < ± 2% of F.S. per year.
Pressure Limits: Ranges up to 6,000 psi: 1.5 x range; 8,000 psi range: 10,000 psi.
Temperature Limits: Ambient: 20 to 140°F (-6.6 to 60°C); Process: 0 to 176°F (-18 to 80°C).
Compensated Temperature Limits: 32 to 122°F (0 to 50°C).
Thermal Effect: ±0.05% of F.S./°F.
Process Connection: 1/4˝ NPT male, 1/4˝ BSPT male, or 7/16” SAE.
Display: 4-digit backlit LCD (Digits: 0.60˝H x 0.33” W).
Display Update: 600 ms (dampening set to 1).
Power Requirements: 12 to 28 VDC ( ) / AC ( ~ ) 50/60 Hz. (Can work at 8 VDC ( ) for 45 seconds). For T5
option: 14 to 30 VDC ( ) / AC ( ~ ) 50/60 Hz.
Power Consumption: 2.5 watts.
Electrical Connections: Removable terminal blocks with two 1/2˝ female NPS conduit connections.
Enclosure Rating: Weatherproof type 4X IP65 (IP65 not evaluated by UL). Unit is rated weatherproof but if unit is
panel mounted, panel will not maintain 4X rating.
Warm Up Time: <10 seconds.
ounting Orientation: Any position.
Weight: 1.18 lbs (535 g).
Installation Category: II (transient over-voltage).
Pollution Degree: 2.
Altitude Limit: 6560 ft (2000 m) max.
Environment: Intended for indoor and outdoor use.
Humidity: 0 to 95% RH up to 104°F (40°C) non-condensing, 10 to 50% at 140°F (60°C) non-condensing.
SWITCH SPECIFICATIONS
Switch Type: 2 SPDT relays.
Electrical Rating: 5A @ 120/240 VAC ( ~ ) 50/60 Hz, 1A @ 28 VDC ( ).
Repeatability: ±1% of FS (switching only).
Set Points: Adjustable 0-100% of FS.
Switch Indication: External LED for each relay on the front panel.
Switch Reset: Manual or automatic.
TRANS ITTER SPECIFICATIONS
Output Signal: 4 – 20 mA, 1 - 6 VDC ( ), 1 - 5 VDC ( ), 0 - 5 VDC ( ), or 0 - 10 VDC ( )(direct or
reverse output selection).
inimum Excitation: 14 VDC ( ).
Zero and Span Adjustments: Menu scalable within the range.
Remote Site Products - 1-888-532-2706 - www.remotesiteproducts.com
http://www.remotesiteproducts.com/p-14331-Dwyer-Mercoid-EDAW-N1E1-09T0-Pressure-Controller.aspx

3
odel Number Chart
Display
The EDA has two displays: a lower larger display and a smaller upper display. The Home Display is the normal dis-
play while the control is in operation if there are no errors or functions active. The Home display will indicate the
process variable at the current condition with the lower display and the selected pressure units for the process vari-
able with the upper display. When programming the unit both displays are also used. The Programming Chart in this
instruction manual indicates what both displays show while programming the unit. For programming descriptions in
this instruction manual the format used is “lower display – upper display”. For example Ctrl – 1SP shows that Ctrl
would be in the lower display and 1SP would be in the upper display.
When the user presses the Ekey to edit an item’s value the upper display will flash “EDIT” and the lower display will
blink. When the user presses the E key to then save the edit to the value the upper display will flash “SAVE” and
the lower display will stop blinking.
Example
Series
Housing
Process
Connection
Electrical
Connection
Range
Transmitter
Output
Options
EDA
EDA
W
N1
B1
A1
E1
01
02
03
04
05
06
07
08
09
10
11*
12*
T0
T1
T2
T3
T4
T5
STW
NIST
23444
EDAW-N1E1-01T0-SST
Electronic Pressure Controller
Weatherproof
1/4˝ NPT male bottom
1/4˝ BSPT male bottom
7/16˝ SAE male bottom
Two 1/2˝ female NPT
conduit connections
0 – 30” Hg vacuum
0 – 20 psi
0 – 60 psi
0 – 100 psi
0 – 150 psi
0 – 300 psi
0 – 600 psi
0 – 1000 psi
0 – 1500 psi
0 – 3000 psi
0 – 6000 psi
0 – 8000 psi
None
4 to 20 mA
1 to 5 VDC
0 to 5 VDC
1 to 6 VDC
0 to 10 VDC
Stainless Steel Tag
NIST Certificate
Special Cleaning
*Not UL listed.
Remote Site Products - 1-888-532-2706 - www.remotesiteproducts.com
http://www.remotesiteproducts.com/p-14331-Dwyer-Mercoid-EDAW-N1E1-09T0-Pressure-Controller.aspx

4
1.0 INSTALLATION
1.1 UNPACKING
Remove the EDA from the shipping carton and inspect for damage. If damage is found, notify the carrier immediate-
ly.
1.2 OUNTING
The EDA can be pipe, panel, or surface mounted. For pipe mounting thread the unit into a mating female fitting on
the pipe. Use a wrench on the 3/4˝ hex at the base of the housing to tighten the unit to the mating fitting. Do not
thread the unit in by force on the housing. For panel mounting the unit fits into a 4-13/16” (122.24 mm) panel cut out.
Insert the unit into the panel opening and secure in place with the machine screws and adaptors provided with the
unit as shown in Figure 1 below. Maximum panel thickness is 1/8” (3.5 mm) with supplied screws. For surface mount-
ing, panel mount the unit into the A-370 mounting bracket (See the Dwyer catalog or website for ordering details)
also shown in Figure 1. The unit can also be directly surface mounted, as shown in Figure 2, with the proper panel
cutout for the conduit entrances. Support the pressure connection hex with a wrench if attaching a fitting to the unit
in the case of panel or flush mounting so that the pressure connection does not twist. Use a small amount of
plumber’s tape or other suitable sealants to prevent leaks around fitting.
Figure 1: Panel ounting and ounting in A-370 Bracket
Figure 2: Surface ounting
A-370 MOUNTING
BRACKET
EDAW SEAL
3X MOUNTING
LUG
3X 4-20 X 3/8 SCREWS
3X 6-20 X 2-1/4 SCREWS
3X 4-20 X 3/8
SCREWS
3X ø 1/8 [3.18]
3-1/16
[77.89]
MOUNTING
HOLE DEPTH
3/8 [9.53]
1-5/8
[41.28]
3-15/32 [88.11]
Remote Site Products - 1-888-532-2706 - www.remotesiteproducts.com
http://www.remotesiteproducts.com/p-14331-Dwyer-Mercoid-EDAW-N1E1-09T0-Pressure-Controller.aspx

1.3 ELECTRICAL CONNECTIONS
CAUTION: POWER UST BE OFF WHILE WIRING CONNECTIONS ARE BEING ADE.
CAUTION: Do not exceed the specified supply voltage rating. Permanent damage not covered by the warranty
may result.
CAUTION: To maintain type 4X rating of the enclosure, 1/2 NPT conduit fittings must have a UL type 4X out-
door rating.
Note: Installation must be made in accordance with local codes and regulations. When fishing wire through the conduit
connection do not allow the wire to touch or press on components on the boards. Damage to the circuitry may result.
Electrical connections are made to the removable terminal blocks inside the enclosure. Remove the top back cover, do
not remove bottom cover. Feed stripped and tinned leads through the conduit opening and connect them as shown in
Figure 3. The EDA provides two 1/2˝ NPT female ports for conduit connection. The conduit connections must be made
such that condensation is not allowed to enter the sensor housing. If necessary install a conduit breather drain in a sep-
arate conduit body to prevent buildup of moisture. It is recommended that shielded twisted pair wire be used for the
transmitter output option if the potential exists for interference from external noise sources. When replacing top back
cover tighten screws to 2 ±.25 in. lbs.
Figure 3: Wiring
An external power supply of 12-28
VDC/AC with minimum current capability
of 200 mA must be used to power the unit.
The power supply connection is not polari-
ty sensitive so the positive and negative
connections may be made to either termi-
nal of CONN9 terminal block.
For voltage output option, connect the volt-
age receiver (-) to terminal 1 and voltage
receiver (+) to terminal 2 of the CONN10
terminal block. For current output option,
connect the current receiver (-) to terminal
3 and current receiver (+) to terminal 4 of
CONN10 terminal block. DO NOT APPLY
EXTERNAL POWER TO CONN10 TER-
MINALS - PERMANENT DAMA E NOT
COVERED BY WARRANTY WILL
RESULT.
Loads can be connected to connectors CONN7 and CONN8 terminal blocks based on the Control settings:
• For single set point mode (CtrL-1SP), connect the Load to SP1 relay (CONN7).
• For two set points mode (CtrL-2SP), connect the Load1 to SP1 relay (CONN7) and
Load2 to SP2 relay (CONN8).
• For single set point and alarm mode (CtrL-SPAL), connect the Load1 to SP1 relay
(CONN7) and Load2 to ALAR relay (CONN8).
Wiring
An external switch or circuit breaker should be added to during the installation as a disconnecting device. The switch
or circuit breaker must meet the requirements of IEC 60947-1 and IEC 60947-3, shall disconnect all current carrying
conductors, and shall not interrupt the protective earth ground. The disconnecting switch or circuit breaker must be
marked or labeled with the symbols “I” for on and “O” for off, per IEC 60417-5007 & IEC 60417-5008 and shall be
marked as “Disconnecting Device”. Do not position the PLS in a space where it is difficult to operate the disconnecting
device that provides power. 300V @ 90°C 18 AW /0.75 mm2wiring with PVC or equivalent insulation with 94-V0 or FV-
0 flammability rating is recommended for the switch outputs and power. Terminal blocks rated for 16-22 solid or strand-
ed copper conductor. 6 lb in is suggested tightening torque.
5
SP1
RELAY
5A 250 VAC FOR LOADS USING 120/240 VAC POWER
1A 32 VDC FOR LOADS USING 30 VDC POWER
375 mA 250 VAC
LOAD 1
LOAD 2
LINE
INPUT
12 TO 30 VDC/AC
POWER
SP2 OR ALARM
RELAY
Description
Direct current
Alternating current
Protective conductor terminal
On (supply)
Off (supply)
Symbol
Explanation of Symbols:
~
Publication
IEC 50417 - 5031
IEC 50417 - 5032
IEC 50417 - 5019
IEC 50417 - 5007
IEC 50417 - 5008
As a permanently installed piece of equipment, a power disconnect switch, circuit breaker, or other
approved disconnect device must be installed in close proximity to the installed board and within
easy reach of the operator. This disconnect device must include a label indicating its function as a mains disconnect. A
circuit breaker or fuse device is recommended (see Figure 3).
WARNING
Remote Site Products - 1-888-532-2706 - www.remotesiteproducts.com
http://www.remotesiteproducts.com/p-14331-Dwyer-Mercoid-EDAW-N1E1-09T0-Pressure-Controller.aspx

6
2. OPERATING INSTRUCTIONS
2.1 FRONT PANEL & KEY FUNCTIONS
Figure 4: Front Panel Functions
Key Functions
HOME POSITION FUNCTION MAIN MENU FUNCTION ITEM FUNCTION
Enter into items
Peak/Valley resets
display to present value.
Remote Site Products - 1-888-532-2706 - www.remotesiteproducts.com
http://www.remotesiteproducts.com/p-14331-Dwyer-Mercoid-EDAW-N1E1-09T0-Pressure-Controller.aspx

7
2.2 SET POINTS & ALAR S
Setting Set Points and Alarms
Set Point Adjustment
Adjusting the set points is quick and simple. Instead of setting a set point and dead band, simply adjust SP1H,
Set Point 1 High, and SP2H, Set Point 2 High, for the desired relay turn on point, and then adjust SP1L, Set Point
1 Low, and SP2L, Set Point 2 Low, for the desired relay turn off point.
In the above graph, an instrument with a 100 psi range would have the SP1 relay turn ON at 80 psi and OFF at 40
psi. SP1H sets the relay turn ON point, and SP1L sets the relay turn OFF point.
The hot key provides direct access to the Set Point and Alarm settings.
The Set Point and Alarm settings that are displayed are based upon the Control (CtrL) menu item.
Remote Site Products - 1-888-532-2706 - www.remotesiteproducts.com
http://www.remotesiteproducts.com/p-14331-Dwyer-Mercoid-EDAW-N1E1-09T0-Pressure-Controller.aspx

8
Relay Action
The relays outputs normally function in the direct acting mode, which means the relays turn ON with an increase in
pressure. SP1 and SP2 may be configured to act as reverse acting relays (refer to the CtrL menu item). When set
for reverse acting, SP1H and SP2H set the relay turn OFF point, and SP1L and SP2L set the relay turn ON point.
The above graph demonstrates direct and reverse action on process (pressure) change.
Alternating (Lead/Lag) Operation
The EDA is designed to easily operate a pair of pumps in an alternating operation to minimize pump wear. The unit
has programmable on and off set points for pump one and two. If the lead/lag feature is turned off then the relays
remain attached to their corresponding set points, SP1H and SP1L control relay 1 (pump 1) and SP2H and SP2L
control relay 2 (pump 2). There is no alternating function.
If lead/lag feature is turned on then the relays will alternate with set points SP1H and SP1L to SP2H and SP2L with
every cycle of set points. The Last relay turned off will be last relay turned on with the next cycle. On the first cycle
on increase of pressure, assuming direct acting, the SP1 relay (pump 1) will come on and then on further increase
of pressure the SP2 relay (pump 2) will come on. On the subsequent decrease of pressure the SP2 relay (pump 2)
will come off and then the SP1 relay (pump 1) will come off. When pressure increases on the next cycle the relay
used on the last cycle for SP2 will now be used for SP1, so that SP1 now controls pump 2 and SP2 now controls
pump 1. Even if SP2 is not used on the pressure cycle the relays still alternate on next cycle.
Remote Site Products - 1-888-532-2706 - www.remotesiteproducts.com
http://www.remotesiteproducts.com/p-14331-Dwyer-Mercoid-EDAW-N1E1-09T0-Pressure-Controller.aspx

9
2.3 PROGRA ING CHART
ENU AP
HOME MAIN MENUS ITEMS SETTINGS
Remote Site Products - 1-888-532-2706 - www.remotesiteproducts.com
http://www.remotesiteproducts.com/p-14331-Dwyer-Mercoid-EDAW-N1E1-09T0-Pressure-Controller.aspx

10
HOME MAIN MENUS ITEMS SETTINGS
CONTROL MODE
SELECTION
ITEMS PRESENT
WHEN “CtrL” SET
TO “1SP”, “2SP”
OR “SPAL”
ITEMS PRESENT
WHEN “CtrL” SET
TO “2SP”
ITEMS PRESENT
WHEN “CtrL” SET
TO “SPAL”
Remote Site Products - 1-888-532-2706 - www.remotesiteproducts.com
http://www.remotesiteproducts.com/p-14331-Dwyer-Mercoid-EDAW-N1E1-09T0-Pressure-Controller.aspx

11
HOME
SEE PAGE 17.
MAIN MENUS ITEMS SETTINGS
Remote Site Products - 1-888-532-2706 - www.remotesiteproducts.com
http://www.remotesiteproducts.com/p-14331-Dwyer-Mercoid-EDAW-N1E1-09T0-Pressure-Controller.aspx

12
2.4 AIN ENU SELECTIONS
enu Selections
Press the ENU button to start the menu so that the upper right displays reads ENU. Press the ▼ key to advance
to the next menu item. You can press the ▲ key to go back to the previous menu. Press the Ekey to enter a menu.
SECr Security Menu
Lock out access to set point and alarm settings, or lock out access to all settings.
OPEr Operation Menu
Select pressure units, zero the display, and turn the backlight on or off.
Out Output Menu
Select relay mode of operation, alternating function, time delay, and lamp indication.
diS Display Menu
Monitor and adjust display related settings: Peak, Valley and Dampening.
AdU Advanced Functions Menu
Modify advanced function parameters: transmitter output scaling, direct or reverse output
setting, calibration, or restoring factory default calibration.
tESt Test Menu
Simulate input over the range without pressure to test switch and transmitter output
function.
FAIL Failsafe Menu
Set the relay and transmitter outputs to certain preset values when failsafe conditions occur.
Error codes will show on the display indicating the problem. User chooses if relay is de-
energized, energized, or no action taken. With transmitter option, user chooses an output
of 3.6 mA, 22 mA, or no action taken.
enus and Values
SECr Security Menu
SECr When the security item is selected, the present security level is displayed in the upper right hand
display. To change the security level, adjust the number displayed to the password value in the
Password Table, shown below, by pressing the ▲ or ▼ key and then pressing the Ekey at the desired
security level.
The password values shown in the table cannot be altered, so retain a copy of these pages for future reference.
Security Level
Displayed
1
2
3
4
Access
All menus access
Menu Access
SP/AL Locked
SP/AL Access
Menus Locked
All settings locked
Password
Value to Enter
10
70
90
111
Remote Site Products - 1-888-532-2706 - www.remotesiteproducts.com
http://www.remotesiteproducts.com/p-14331-Dwyer-Mercoid-EDAW-N1E1-09T0-Pressure-Controller.aspx

13
OPEr Operation Menu
Unit Pressure Units
With the display reading Unit - PSI, press the Ekey. The upper display will blink. Press the ▼ key to
change unit then press Ekey to save the new unit.
PSI Pounds per square inch
FS % of full scale
OZIN Ounces per square inch
CWC Centimeters of water column
PA Megapascals
BAR Bar
BAR Millibar
KPA Kilopascals
FTWC Feet of water column
KGC Kilograms per square centimeter
HG Millimeters of mercury
INWC Inches of water column
INHG Inches of mercury
Pressure Range vs. Available Units
ZERO Auto Zero
Note: DO NOT apply any pressure when performing this function. With the display
reading xx - ZERO, press the Ekey. The upper display will blink. Press Eagain to zero the display.
The display will read 0.0 if the zero offset is less than ±5% of full scale.
bCLt Backlight
ON Backlight always on.
OFF Backlight always off.
30 Backlight stays on for 30 minutes.
10 Backlight stays on for 10 minutes.
5 Backlight stays on for 5 minutes.
2Backlight stays on for 2 minutes.
PSI
-14.70
20.00
60.0
100.0
150.0
300.0
600
1000
1500
3000
6000
8000
KG/C 2
-1.033
1.406
4.22
7.03
10.55
21.09
42.2
70.3
105.5
210.9
422
562
BAR
-1.013
1.379
4.14
6.89
10.34
20.68
41.4
68.9
103.4
206.8
414
551
INHg
-29.93
40.7
122.2
203.6
305.4
611
1222
2036
3054
FTWC
-33.94
46.1
138.4
230.7
346.0
692
1384
2307
3460
KPA
-101.4
137.9
414
689
1034
2068
PA
-0.101
0.1379
0.414
0.689
1.034
2.068
4.14
6.89
10.34
20.68
41.4
55.1
INWC
-407.3
554
1663
2771
BAR
-1013
1379
C WC
-1034
1406
Hg
-761
1035
3105
OZ/IN2
-235.2
320.0
960
1600
2400
% FS
100
100
100
100
100
100
100
100
100
100
100
100
Remote Site Products - 1-888-532-2706 - www.remotesiteproducts.com
http://www.remotesiteproducts.com/p-14331-Dwyer-Mercoid-EDAW-N1E1-09T0-Pressure-Controller.aspx

14
OUt Output Menu
CtrL Control Mode
1SP Single set point.
2SP Two fully independent set points.
SPAL Single set point and alarm.
1SP SP1, Set Point 1, Reverse or Direct Acting
DIR Direct. Relay turns on with increasing pressure.
REV Reverse. Relay turns on with decreasing pressure.
DEL1 SP1, Set Point 1, Time Delay
Sets the amount of time a set point condition must be continuously met before the set point condition
is recognized. The DEL1 delay is adjustable from 0-60 seconds.
LEd1 SP1, Set Point 1, Lamp
OFF The SP1 LED on the front panel turns OFF when the SP1 relay turns OFF.
The SP1 LED on the front panel turns ON when the SP1 relay turns ON.
ON The SP1 LED on the front panel turns ON when the SP1 relay turns OFF.
The SP1 LED on the front panel turns OFF when the SP1 relay turns ON.
The following SP2 function values are only activated when CtrL is set to 2SP:
2SP SP2, Set Point 2, Reverse or Direct Acting
DIR Direct. Relay turns on with increasing pressure.
REV Reverse. Relay turns on with decreasing pressure.
DEL2 SP2, Set Point 2, time delay
Sets the amount of time a set point condition must be continuously met before the set point
condition is recognized. The DEL2 delay is adjustable from 0-60 seconds.
LEd2 SP2, Set Point 2, Lamp
OFF The SP2 LED on the front panel turns OFF when the SP2 relay turns OFF.
The SP2 LED on the front panel turns ON when the SP2 relay turns ON.
ON The SP2 LED on the front panel turns ON when the SP2 relay turns OFF.
The SP2 LED on the front panel turns OFF when the SP2 relay turns ON.
LdL9 Relay Alternation (See page 8)
OFF There is no alternating function.
ON Relays will alternate with set points SP1H/L and SP2H/L with every cycle of set
points. 2SP control mode only.
Remote Site Products - 1-888-532-2706 - www.remotesiteproducts.com
http://www.remotesiteproducts.com/p-14331-Dwyer-Mercoid-EDAW-N1E1-09T0-Pressure-Controller.aspx

15
The following alarm function menu items are activated when CtrL is set to SPAL:
DELA Alarm Delay
Sets the amount of time an alarm condition must be continuously met before the alarm condition is
recognized. The alarm delay is adjustable from 0 - 60 seconds.
LEdA Alarm Lamps
OFF The ALLO LED or ALHI LED on the front panel turns OFF when the alarm relay
turns OFF. The ALLO LED or ALHI LED on the front panel turns ON when the
alarm relay turns ON.
ONThe ALLO LED or ALHI LED on the front panel turns ON when the alarm relay
turns OFF. The ALLO LED or ALHI LED on the front panel turns OFF when the
alarm relay turns ON.
AL Alarm Type (see Alarm Adjustment below)
HIGH High alarm only.
LOW Low alarm only.
HILO For a high and low guard band type alarm. Share the same relay output.
Alarm Adjustment
Alarm settings are dependent upon the selected alarm type. The EDA pressure controller alarm may be configured
as a High Alarm, Low Alarm, or High/Low Alarm. Alarm settings may be set to anywhere within the range of the
instrument. The dead bands of the alarms are fixed at 1% of full scale.
ALrE Alarm Reset
AUTO Automatic reset.
HOLD Manual reset. An alarm is reset by pressing the RST key on the front panel.
ALiH Low Alarm Inhibit
OFF Alarm inhibit is off.
ON Alarm inhibit is on.
Note: If ALiH is selected ON, a low alarm condition is suspended upon power up until the process value passes
through the alarm set point once.
Remote Site Products - 1-888-532-2706 - www.remotesiteproducts.com
http://www.remotesiteproducts.com/p-14331-Dwyer-Mercoid-EDAW-N1E1-09T0-Pressure-Controller.aspx

16
diS Display Menu
PEAK Peak
The Peak feature stores the highest pressure reading the instrument has measured since
the last reset or power up. At power up PEAK is reset to the present pressure reading. To manually
reset the PEAK value, press the RST (RESET) key while in PEAK.
VALY Valley
The Valley feature stores the lowest pressure reading the instrument has measured since
the last reset or power up. At power up VALY is reset to the present pressure reading. To manually
reset the VALY value, press the RST (RESET) key while in VALY.
DA P Dampening
Adjust from 1-15. Dampening stabilizes the display from instabilities due to things such as vibration
and excessive pressure fluctuations. The dampening setting adjusts the amount of readings that are
averaged for each display update. Adjust the dampening value until the display reads a stable value for
the application.
AdU Advanced Menu
POL, Process Output Low, and POH, Process Output High are used to scale the transmitter output for a unit with
the output option of 4 to 20 mA, 0-5 VDC, 0-10 VDC, 1-5 VDC, or 1-6 VDC. Below shows with 4 to 20 mA output
option.
POL Process Output Low
Set to the desired display reading for the 4 mA output. May be set from 2% below
minimum scale up to POH.
POH Process Output High
Set to the desired display reading for the 20 mA output. May be set from POL to 2% above maximum
scale.
CAL – ZERO Zero Calibration
DO NOT apply any pressure when performing this function. With the display
reading CAL - ZERO, press the Ekey. The upper display will blink. Press the E
key again to complete the zeroing of the instrument or press the ENU key to cancel.
CAL – FS Full-scale Calibration
With the display reading CAL - FS, apply full-scale pressure to the unit, press the E key.
The upper display will blink. Press the Ekey again to complete the
calibration or press the ENU key to cancel.
trAn sets the transmitter output option function for a unit with the output option of 4 to 20 mA, 0-5 VDC, 0-10 VDC,
1-5 VDC, or 1-6 VDC. Below shows with 4 to 20 mA output option.
trAn
DIR Direct Output. 4 mA output at zero, 20 mA output at full scale pressure.
REV Reverse Output. 20 mA output at zero, 4 mA output at full scale pressure.
CAL - DFLT Factory Default Calibration
With the display reading CAL - DFLT, press the Ekey. The upper display will blink.
Press Eagain to restore the original factory calibration values or press the ENU key
to cancel.
Remote Site Products - 1-888-532-2706 - www.remotesiteproducts.com
http://www.remotesiteproducts.com/p-14331-Dwyer-Mercoid-EDAW-N1E1-09T0-Pressure-Controller.aspx

tESt Test Menu
tESt When selected the unit simulates a pressure input over the range to test the programming and output
function. To start an automatic simulated cycling through the pressure range press the Ekey. This test
will run continually until the Ekey is pressed again. To manually adjust the simulated pressure
press the ▲ or ▼ key to adjust the pressure value. To exit tESt press the ENU key.
FAIL Failsafe Menu
The Failsafe menu is used to set the relay and transmitter outputs to certain preset values when failsafe conditions
occur. Error codes will show on the display indicating the problem. See Diagnostic Error Messages on the next page.
rEL Relay Output Failsafe Condition
OPEN The relay is de-energized upon failsafe condition. The NO contacts will be
opened, and the NC contacts will be closed.
CLSE The relay is energized upon failsafe condition. The NO contacts will be closed,
and the NC contacts will be opened.
NOR No change applied to the relay upon failsafe condition.
OUtP sets the transmitter output option failsafe condition for a unit with the output option of 4 to 20 mA, 0-5 VDC,
0-10 VDC, 1-5 VDC, or 1-6 VDC. See below chart of transmitter output action according to output signal type.
OUtP Transmitter Output Failsafe Condition
LOW Transmitter output goes to low failsafe condition.
HIGH Transmitter output goes to high failsafe condition.
NOR No change applied to transmitter output upon failsafe condition.
FrEs Failsafe reset
AUTO Automatic reset - Failsafe is reset automatically when the failsafe error condition
is removed.
HOLD Manual reset - Failsafe is reset when the ENU key is pressed.
17
Output signal
LOW
HI H
4-20 mA
3.6 mA
22 mA
0-5 VDC
-0.125 VDC
5.625 VDC
0-10 VDC
-0.250 VDC
11.250 VDC
1–6 VDC
0.875 VDC
6.625 VDC
1-5 VDC
0.9 VDC
5.5 VDC
Remote Site Products - 1-888-532-2706 - www.remotesiteproducts.com
http://www.remotesiteproducts.com/p-14331-Dwyer-Mercoid-EDAW-N1E1-09T0-Pressure-Controller.aspx

DWYER INSTRU ENTS, INC. Phone: [phone] www.dwyer-inst.com
P.O. BOX 373 • ICHIGAN CITY, IN 46360, U.S.A. Fax: [phone] e-mail: [email protected]
©Copyright 2013 Dwyer Instruments, Inc. Printed in U.S.A. 6/13 FR# 76-443725-00 Rev.4
4. DIAGNOSTIC ERROR ESSAGES
5. AINTENANCE/REPAIR
Upon final installation of the Series EDA, inspect and clean with water or damp cloth at regular intervals. The Series
EDA is not field serviceable and should be returned if repair is needed (field repair should not be attempted and may
void warranty.
6. WARRANTY/RETURN
Refer to “Terms and Conditions of Sales” in our catalog and on our website. Contact customer service to receive a
Return oods Authorization number before shipping the product back for repair. Be sure to include a brief descrip-
tion of the problem plus any additional application notes.
Display
Err1
Err2
Err3
Err4
Err5
eaning
Low temperature limit
A temperature below 0°F has been applied to the sensor
High temperature limit
A temperature above 180°F has been applied to the sensor
Sensor failure
The micro-controller is receiving invalid signal from the sensor
Over pressure limit
Proof pressure have been exceeded
Keypad short
Remote Site Products - 1-888-532-2706 - www.remotesiteproducts.com
http://www.remotesiteproducts.com/p-14331-Dwyer-Mercoid-EDAW-N1E1-09T0-Pressure-Controller.aspx