Fairchild NC7SB3257 TinyLogic Operating and maintenance instructions

© 2002 Fairchild Semiconductor Corporation DS500325 www.fairchildsemi.com
January 2000
Revised April 2002
NC7SB3257 TinyLogic

UHS 2:1 Multiplexer/Demultiplexer Bus Switch
NC7SB3257
TinyLogicUHS
2:1 Multiplexer/Demultiplexer Bus Switch
General Description
The NC7SB3257 is a high performance, 2:1 NMOS pass-
gate multiplexer/demultiplexer from Fairchild’s Ultra High
Speed Series of TinyLogic. The device is fabricated with
advanced sub-micron CMOS technology to achieve high
speed enable and disable times and low On Resistance.
The device is specified to operate over the 4.0 to 5.5V VCC
operating range. The control input tolerates voltages up to
5.5V independent of the VCC operating range.
Features
■Space saving SC70 6-lead surface mount package
■Ultra small MicroPakleadless package
■Typical 3Ωswitch resistance @ 5.0V VCC
■Minimal propagation delay through the switch
■Power down high impedance control input
■Zero bounce in flow through mode
■TTL compatible control input
■Overvoltage tolerance of control input to 7.0V
■Break before make enable circuitry
Ordering Code:
TinyLogicand MicroPakare trademarks of Fairchild Semiconductor Corporation.
Order
Number Package Number Product Code Top Mark Package Description Supplied As
NC7SB3257P6X MAA06A B7B 6-Lead SC70, EIAJ SC88, 1.25mm Wide 3k Units on Tape and Reel
NC7SB3257L6X MAC06A B7 6-Lead MicroPak, 1.0mm Wide 5k Units on Tape and Reel

www.fairchildsemi.com 2
NC7SB3257
Logic Symbol
Pin Descriptions
Function Table
H =HIGH Logic Level
L =LOW Logic Level
Connection Diagrams
Pin Assignments for SC70
(Top View)
Pin One Orientation Diagram
AAA =Product Code Top Mark - see ordering code
Note: Orientation of Top Mark determines Pin One location. Read the top
product code mark left to right, Pin One is the lower left pin (see diagram).
Pad Assignments for MicroPak
(Top Thru View)
Pin Names Description
A, B0, B1Data Ports
S Control Input
Input (S) Function
LB
0Connected to A
HB
1Connected to A

3 www.fairchildsemi.com
NC7SB3257
Absolute Maximum Ratings(Note 1) Recommended Operating
Conditions (Note 2)
Note 1: Absolute maximum ratings are DC values beyond which the device
may be damaged or have its useful life impaired. The datasheet specifica-
tions should be met, without exception, to ensure that the system design is
reliable over its power supply, temperature, and output/input loading vari-
ables. Fairchild does not recommend operation outside datasheet specifi-
cations.
Note 2: Control input must be held HIGH or LOW, it must not float.
Note 3: The input and output negative voltage ratings may be exceeded if
the input and output diode current ratings are observed.
DC Electrical Characteristics
Note 4: Measured by the voltage drop between A and B pins at the indicated current through the switch. On Resistance is determined by the lower of the
voltages on the two (A or B Ports).
Note 5: Per TTL driven Input (VIN =3.4V, Control input only). A and B pins do not contribute to ICC.
Supply Voltage (VCC)−0.5V to +7.0V
DC Switch Voltage (VS)−0.5V to +7.0V
DC Output Voltage (VIN)−0.5V to +7.0V
DC Input Diode Current (IIK)
@ (IIK) VIN <0V −50 mA
DC Output Current (IOUT) 128 mA
DC VCC or Ground Current (ICC/IGND)±100 mA
Storage Temperature Range (TSTG)−65°C to +150°C
Junction Lead Temperature under Bias (TJ)+150°C
Lead Temperature (TL)
(Soldering, 10 seconds) +260°C
Power Dissipation (PD) @ +85°C180mW
Supply Voltage Operating (VCC) 4.0V to 5.5V
Control Input Voltage (VIN)0VtoV
CC
Switch Input Voltage (VIN)0VtoV
CC
Output Voltage (VOUT)0VtoV
CC
Operating Temperature (TA)−40°C to +85°C
Input Rise and Fall Time (tr, tf)
Control Input VCC =4.0V to 5.5V 0 ns/V to 5 ns/V
Thermal Resistance (θJA)350°C/W
Symbol Parameter VCC TA=−40°C to +85°CUnits Conditions
(V) Min Typ Max
VIK Clamp Diode Voltage 4.5 −1.2 V IIN =−18 mA
VIH HIGH Level Input Voltage 4.5 −5.5 2.0 V
VIL LOW Level Input Voltage 4.5 −5.5 0.8
IIN Input Leakage Current 5.5 ±1µA0≤VIN ≤5.5V
IOFF OFF State Leakage Current 5.5 ±1µA0≤A, B ≤VCC
RON Switch ON Resistance (Note 4) 4.5 3 7 ΩVIN =0V, IIN =64 mA
4.5 3 7 ΩVIN =0V, IIN =30 mA
4.5 6 15 ΩVIN =2.4V, IIN =15 mA
4.0 10 20 ΩVIN =2.4V, IIN =15 mA
ICC Quiescent Supply Current 5.5 10 µAV
IN =VCC or GND
IOUT =0
∆ICC Increase in ICC Per Input (Note 5) 5.5 0.9 2.5 mA VIN =3.4V, IO=0
Control Input Only

www.fairchildsemi.com 4
NC7SB3257
AC Electrical Characteristics
Note 6: This parameter is guaranteed by design but not tested. The bus switch contributes no propagation delay other than the RC delay of the On Resis-
tance of the switch and the 50 pF load capacitance, when driven by an ideal voltage source (zero output impedance).
Note 7: Guaranteed by design.
Capacitance (Note 8)
Note 8: Capacitance is characterized but not tested.
Symbol Parameter
TA=−40°C to +85°C
Units ConditionsVCC CL=50 pF, RU =RD =500ΩFigure
(V) Min Typ Max Number
tPHL Propagation Delay Bus to Bus 4.0 −55 0.25 ns VI=OPEN Figures
1, 2
tPLH (Note 6)
tPZL Output Enable Time 4.5 −5.5 1.8 6.5 ns VI=7V for tPZL Figures
1, 2
tPZH 4.0 1.8 7.3 VI=0V for tPZH
tPLZ Output Disable Time 4.5 −5.5 0.8 4.7 VI=7V for tPLZ Figures
1, 2
tPHZ 4.0 0.8 5.3 VI=0V for tPHZ
tB-M Break Before Make Time 4.5 −5.5 0.5 ns Figure 3
(Note 7) 4.0 0.5
Symbol Parameter Typ Max Units Conditions
CIN Control Pin Input Capacitance 2.3 pF VCC =0V
CIO-B B Port OFF Capacitance 5.7 pF VCC =5.0V
CIO-A A Port ON Capacitance 16 pF VCC =5.0V

5 www.fairchildsemi.com
NC7SB3257
AC Loading and Waveforms
Note: Input Driven by 50Ωsource terminated in 50Ω
Note: CLincludes load and stray capacitance
Note: Input PRR =1.0 MHz; tW=500 ns
FIGURE 1. AC Test Circuit
Input =AC Waveform;
PRR =Variable; Duty Cycle =50% FIGURE 2. AC Waveforms
FIGURE 3. Break Before Make Interval Timing

www.fairchildsemi.com 6
NC7SB3257
Tape and Reel Specification
TAPE FORMAT for SC70
TAPE DIMENSIONS inches (millimeters)
Package Tape Number Cavity Cover Tape
Designator Section Cavities Status Status
Leader (Start End) 125 (typ) Empty Sealed
P6X Carrier 3000 Filled Sealed
Trailer (Hub End) 75 (typ) Empty Sealed
Package Tape Size DIM A DIM B DIM F DIM KoDIM P1 DIM W
SC70-6 8 mm 0.093 0.096 0.138 ±0.004 0.053 ±0.004 0.157 0.315 ±0.004
(2.35) (2.45) (3.5 ±0.10) (1.35 ±0.10) (4) (8 ±0.1)

7 www.fairchildsemi.com
NC7SB3257
Tape and Reel Specification (Continued)
TAPE FORMAT for MicroPak
REEL DIMENSIONS inches (millimeters)
Package Tape Number Cavity Cover Tape
Designator Section Cavities Status Status
Leader (Start End) 125 (typ) Empty Sealed
L6X Carrier 5000 Filled Sealed
Trailer (Hub End) 75 (typ) Empty Sealed
Tape
Size ABCDN W1 W2 W3
8 mm 7.0 0.059 0.512 0.795 2.165 0.331 +0.059/−0.000 0.567 W1 +0.078/−0.039
(177.8) (1.50) (13.00) (20.20) (55.00) (8.40 +1.50/−0.00) (14.40) (W1 +2.00/−1.00)

www.fairchildsemi.com 8
NC7SB3257
Physical Dimensions inches (millimeters) unless otherwise noted
6-Lead SC70, EIAJ SC88, 1.25mm Wide
Package Number MAA06A

Physical Dimensions inches (millimeters) unless otherwise noted (Continued)
9 www.fairchildsemi.com
NC7SB3257 TinyLogic

UHS 2:1 Multiplexer/Demultiplexer Bus Switch
Physical Dimensions inches (millimeters) unless otherwise noted (Continued)
6-Lead MicroPak, 1.0mm Wide
Package Number MAC06A
Fairchild does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and
Fairchild reserves the right at any time without notice to change said circuitry and specifications.
LIFE SUPPORT POLICY
FAIRCHILD’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT
DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT OF FAIRCHILD
SEMICONDUCTOR CORPORATION. As used herein:
1. Life support devices or systems are devices or systems
which, (a) are intended for surgical implant into the
body, or (b) support or sustain life, and (c) whose failure
to perform when properly used in accordance with
instructions for use provided in the labeling, can be rea-
sonably expected to result in a significant injury to the
user.
2. A critical component in any component of a life support
device or system whose failure to perform can be rea-
sonably expected to cause the failure of the life support
device or system, or to affect its safety or effectiveness.
www.fairchildsemi.com