Falcon E702S User guide

T100677 Ref. 3
WEEE Directive Registration No. WEE/DC0059TT/PRO
At end of unit life, dispose of appliance and any replacement
parts in a safe manner, via a licenced waste handler.
Units are designed to e dismantled easily and recycling of all
material is encouraged whenever practica le.
E7202S/E7202 BE1 and BE2
E7202 B 1 and B 2
CONVECTION OVEN
INSTALLATION and
SERVICING INSTRUCTIONS
IMPORTANT
The installer must ensure that the installation of the appliance is in conformity with these instructions and
National Regulations in force at the time of installation. Particular attention MUST e paid to -
BS7671 IEE Wiring Regulations
Electricity at Work Regulations
Health And Safety At Work Act
ire Precautions Act
This appliance has een CE-marked on the asis of compliance with the Low Voltage and EMC Directives for
the voltages stated on the Data Plate
WARNING -THIS APPLIANCE MUST BE EARTHED
On completion of the installation these instructions should e left with the Engineer-in-Charge for reference
during servicing. Further to this, The Users Instructions should e handed over to the User, having had a
demonstration of the operation and cleaning of the appliance.
IT IS MOST IMPORTANT THAT THESE INSTRUCTIONS BE CONSULTED BE ORE INSTALLING AND
COMMISSIONING THIS APPLIANCE. AILURE TO COMPLY WITH THE SPECI IED PROCEDURES MAY
RESULT IN DAMAGE OR THE NEED OR A SERVICE CALL.
PREVENTATIVE MAINTENANCE CONTRACT
In order to o tain maximum performance from this unit we would recommend that a Maintenance Contract e
arranged with SERVICELINE . Visits may then e made at agreed intervals to carry out adjustments and
repairs. A quotation will e given upon request to the contact num ers elow.
alcon oodservice Equipment
HEAD O ICE AND WORKS
Wallace View, Hillfoots Road, Stirling. FK9 5PY. Scotland.
SERVICELINE CONTACT -
PHONE - 01438 363 000 FAX - 01438 369 900

Warranty Policy Shortlist
Warranty does not cover :-
Correcting faults caused y incorrect installation of a product.
Where an engineer cannot gain access to a site or a product.
Repeat commission visits.
Replacement of any parts where damage has een caused y misuse.
Engineer waiting time will e chargea le.
Routine maintenance and cleaning.
Gas conversions i.e. Natural to Propane gas.
Descaling of water products and cleaning of water sensors where softeners/conditioners are not fitted, or are
fitted and not maintained.
Blocked drains.
Independent steam generation systems.
Gas, water and electrical supply external to unit.
Light ul s.
Re-installing vacuum in kettle jackets.
Replacement of grill urner ceramics when damage has een clearly caused y misuse.
Where an engineer finds no fault with a product that has een reported faulty.
Re-setting or adjustment of thermostats when unit is operating to specification.
Cleaning and un locking of fryer filter systems due to customer misuse.
Lu rication and adjustment of door catches.
Cleaning and Maintenance
Cleaning of urner jets
Poor com ustion caused y lack of cleaning
Lu rication of moving parts
Lu rication of gas cocks
Cleaning/adjustment of pilots
Correction of gas pressure to appliance.
Renewing of electric ca le ends.
Replacement of fuses
Corrosion caused y use of chemical cleaners.

SECTION 1 - INSTALLATION
UNLESS OTHERWISE STATED, PARTS WHICH
HAVE BEEN PROTECTED BY THE
MANU ACTURER ARE NOT TO BE ADJUSTED
BY THE INSTALLER
1.2 SITING
The units are suita le for installation upon any flat,
horizontal surface. Adjusta le feet to facilitate
levelling within a limited range. Position oven in
desired location and use a suita le spanner to level.
Sufficent clearance should e left around unit to allow
turning for maintenance purposes.
1.3 ELECTRICAL SUPPLY and CONNECTION
These ovens are designed to e connected to a
single phase 230V/50hz AC supply. The unit power
rating is 2.65kW. The mains lead is fitted with a
moulded fused plug to BS1363 with 13 amp fuse
fitted. The mains lead wires are coloured in
accordance with the following code:
Green and Yellow EARTH
Blue NEUTRAL
Brown LIVE
These wires should e connected as follows:
EARTH to terminal marked E
NEUTRAL to terminal marked N
LIVE to terminal marked L
Warning - This appliance MUST be earthed!
Any replacement supply ca le must e 1.5mm
2
, cord
code designation 245 IEC 57 (Cenelec H05 RN-F).
For internal connection, outer sheathing must e
stripped 140mm from ca le end. Live and Neutral
conductors must e trimmed so that earth conductor
is longer y 50mm. Pass inlet ca le through rear
panel cord grip and ensure ca le is routed without
leaving excessive free length inside unit.
1.4 INSTRUCTION TO USER
Upon completion of installation, the correct method of
operation should e demonstrated to kitchen staff.
Location of the main isolating switch should also e
indicated, to e used in event of an emegency or
during cleaning.
SECTION 2 - SERVICING and
MAINTENANCE
Warning
BEFORE ATTEMPTING TO UNDERTAKE ANY
MAINTENANCE TASK. ISOLATE THE POWER AT
THE MAIN SWITCH AND TAKE STEPS TO
ENSURE THIS CANNOT BE INADVERTENTLY
SWITCHED ON.
2.1 OVEN CONTROL PANEL
2.1.1 Control Panel
Undo two fixings on underside of oven until location
pins allow panel to drop forward.
2.1.2 To Remove Rear Panel
a) Slacken fixings ehind elongated slots at top of
panel.
) Lift panel clear of these fixings.
c) Replace in reverse order.
2.1.3 To Remove Outer Casing
a) Remove rear panel. See Sections 2.1.2.
) Undo fixings that secure casing to ase.
c) Remove top and ottom hinge fixing screws.
d) Pull casing sides away from ase and lift casing.
e) Replace in reverse order.
2.1.4 To Remove Oven Back Baffle
a) Remove oven shelves.
) Raise shelf hangers from keyhole slots and
remove.
c) Slacken ack affle fixing screws.
d) Raise affle on keyhole slots to remove.
e) Replace in reverse order.
2.1.5 To Remove Elements
a) Remove ack affle. Refer to Section 2.1.4.
) Remove rear panel as detailed in Section 2.1.2.
c) Undo element connections at oven rear.
d) Remove fixings at rear of oven cavity.
e) Withdraw element.
f) Replace in reverse order and ensure earth ta is
connected.
2.1.6 To Remove an
a) Remove affle. Refer to Section 2.1.4.
) Remove rear panel. Refer to Section 2.1.2.
c) Undo fan wires.
d) Remove earth lead.
e) Undo impeller retaining nut (LH thread) and
remove impeller.
f) Undo fixings that secure motor to oven rear and
withdraw.
g) Replace in reverse order.
MODEL WIDTH
mm DEPTH mm HEIGHT mm WEIGHT kg WEIGHT l s
E7202S 667 570 550 50 110
E7202 BE1 667 570 550 50 110
E7202 BE2 667 570 550 50 110
E7202 BF1 667 570 550 50 110
E7202 BF1 667 570 550 50 110
1.1 MODEL NUMBER, NETT WEIGHTS
and DIMENSIONS

2.1.7 To Remove Neon Indicators
a) Open control panel. Refer to Section 2.1.1.
) Remove connections, noting their positions.
c) Remove securing nut and withdraw neon.
d) Replace in reverse order.
2.1.8 To Remove Cook Thermostat/fan Switch
a) Open main control panel.
) Remove control kno .
c) Remove connections, noting their positions.
d) Undo fixings which secure thermostat to control
panel.
e) Undo phial guard fixing to remove guard and
retaining rackets.
f) Feed phial ack through oven side hole.
g) Remove extension spindle and phial sleeving.
h) Replace in reverse order.
2.1.9 To Remove Timer
a) Open control panel. Refer to Section 2.1.1.
) Remove connections, noting their positions.
c) Remove control kno .
d) Remove fixings which secure timer to control
panel.
e) Replace in reverse order.
2.1.10 Hold Thermostat (when fitted)
a) Remove outer casing as detailed in Section 2.1.3.
) It is possi le to adjust hold thermostat temperature
etween 75 and 85
o
C y means of the spindle.
To Remove
c) Disconnect electrical leads.
d) Undo fixings which secure thermostat to racket.
2.1.11 To Remove Power Input Cable
a) Remove rear panel. Refer to Section 2.1.2.
) Slacken ca le securing clamp.
c) Undo terminal lock and earth post nut fixings.
d) Replace in reverse order. Replace plug and ca le
type as detailed in Section 1.3. Ensure ca le is fed
through securing clamp and pulled tight efore
clamp is secured.
2.1.12 To Remove Buzzer
a) Open control panel, refer to Section 2.1.1.
) Disconnect uzzer wiring noting wire positions.
c) Remove fixing which secures uzzer to racket.
d) Replace in reverse order.
2.1.13 To Replace Door Seal
a) Unclip seal from front frame.
2.1.14 To Replace Door Catch
a) Drill out pop rivets which secure inner and outer
door panels.
) Drill out rivets which secure catch.
c) Replace in reverse order.
2.1.15 To Replace Door Stud
a) Undo locknut and remove stud.
) Replace stud and adjust as detailed in Figure 1
efore tightening locknut.
igure 1
2.1.16 To Remove Oven Light (When itted)
a) Remove RH shelf hanger.
) Undo lamp cover fixing screws.
c) Open control panel.
d) Undo lamp wiring connections.
e) Unclip lamp housing from aperture.
f ) Replace in reverse order.
2.1.17 To Remove Light Switch (When itted)
a) Open control panel. Refer to Section 2.1.1.
) Slacken switch retaining nut.
c) Unscrew ezel and remove push utton.
d) Replace in reverse order.
2.1.18 To Remove High Temperature Limit Device
a) Remove control panel as detailed in Section 2.1.
) Remove connections, noting positions.
c) Undo fixings that secure device to ase panel.
d) From inside oven, remove phial guard located at
top RH side of unit.
e) Feed phial ack through oven side hole.
f) Replace in reverse order.
2.1.19 Service
Contact Serviceline num er indicated on title page.
2.1.20 Spares
When ordering spares, please quote model num er,
serial num er and voltage as indicated on unit data
plate.

E7202S/BE1/BE2 Convection Ovens - Wiring Diagram (Drawing No : AW36933)

E7202 B 1 & B 2 Convection Ovens - Wiring Diagram (Drawing No : AW46911)