Fan-Tastic Vent 7350 User manual

1
STEP 3 & 3b. DISCONNECT POWER SUPPLY WIRES (BLACK &
WHITE or RED AND WHITE) ON DRIVER SIDE OF FAN BY UNPLUG-
GING OR CUTTING 2”-3” FROM STRAIN RELIEF KNOTS.
Cut Dome Switch Wire
Remove the Fuse Remove 5 Screws
1b 2
Strip the End
STEP 5c & 5d. STRIP OFF INSULATION ON THE FAN MOTOR
LEAD WIRE APPROX. 3/8” FROM THE END AND PUT THE BLUE
FEMALE CLIP (provided) ON THE BARE END AND CRIMP IT
SECURELY. CONNECT THE FAN MOTOR LEAD (RED or BLUE)
WIRE TO THE RED AND BLUE STRIPED WIRE ON YOUR NEW
UPGRADED SCREEN ASSEMBLY.
Crimp Blue Female Clip
Open Dome 2/3rds
Unhook Lift-Arm and Remove
Unscrew the Lift-Arm ASM
Feed the Lead Back Up Thru Base
5d
Drop Control Panel
2b
STEP 4 & 4b. (If you have a Manual Fan), REMOVE 2 SCREWS FROM
THE LIFT ARM ASM BASE, UNHOOK THE LIFT-ARM FROM THE DOME SLIDE
AND PULL THROUGH THE SLOT IN THE BASE. PUT NEW LIFT-ARM
THROUGH SLOT IN BASE AND HOOK TO SLIDE ON DOME. SECURE LIFT-
ARM ASM TO THE BASE WITH TWO #10 SCREWS.
Cut the Clip Off (only)
5 5b
1
INSTALLATION INSTRUCTIONS.
Read Instructions Entirely Before Beginning *NOTE: ALL ASSEMBLY SCREWS ARE STANDARD #2 PHILLIPS
STEP 5 & 5b. (IF NOT ORIGINALLY EQUIPPED WITH A REVERSE SWITCH),
UNPLUG THE RED or BLUE WIRE FAN MOTOR LEAD FROM THE 3-
SPEED SWITCH. CUT THE CLIP OFF OF THE FAN MOTOR LEAD.
PULL THE WIRE OUT OF THE BASE FROM THE TOP SIDE.
LOCATE THE HOLE NEXT TO THE DOME SWITCH AND FEED THE
FAN MOTOR LEAD THROUGH TO THE INSIDE (5b).
4b
STEP 2 & 2b. REMOVE THE LIFT KNOB (MANUAL) OR LIFT
MOTOR (AUTO). NOW REMOVE 3 TO 5 SCREWS FROM THE FACE
OF THE SCREEN ASSEMBLY (ASM) (removal of the screen is not
necessary)..
5c
Unplug Dome Switch
4
STEP 1 & 1b. OPEN THE DOME 2/3rds. REMOVE THE FUSE
FROM BOTH CURRENT AND NEW SCREEN ASSEMBLY BY
PUSHING UP THE BLACK FUSE CAP 1/4 TURN LEFT AND PULL!
(SINCE ‘97 SOME CAPS REQUIRE A SLOTTED SCREWDRIVER)
33b

FAN-TASTIC VENT, P.O. BOX 1627, ELKHART, IN 46515-1627
TEL. [phone] www.fantasticvent.com
STEP 9. REPLACE THE FUSE (from step 1) IN YOUR NEW
CONTROL PANEL AND ENJOY YOUR UPGRADED FAN-TASTIC
VENT. IF YOU NEED INSTALLATION HELP OR HAVE ANY OPERA-
TION QUESTIONS, CALL US MONDAY THROUGH FRIDAY 9:00 am -
5:00 pm TOLL FREE @ 800-521-0298
STEP 7 & 7b. A “T” SHAPED KNOCKOUT FOR THE RAIN
SENSOR IS LOCATED INSIDE THE FAN BASE, 4”-5” FORWARD OF
THE PASSENGER REAR CORNER. USE A HAMMER AND SCREW-
DRIVER TO “KNOCK IT OUT”.
STEP 7c & 7d. FEED THE RAIN SENSOR THROUGH THE “T”
SLOT, SECURING IT ON TOP OF THE BASE WITH THE #6 x 1/4”
PANHEAD PHILLIPS SCREW (SUPPLIED) AFTER HOOKING LEAD
SIDE ON PEG.
STEP 8. TUCK LOOSE WIRES AS NEEDED. SECURE THE
ENTIRE SCREEN ASSEMBLY AND LIFT MOTOR WITH 5 SCREWS
(BE SURE THE LIFT MOTOR SHAFT FITS OVER TOP OF THE
KNURLED END OF THE LIFT ARM).
Install New Control Panel Close the Dome Lid Replace the Fuse
10
Enjoy Your New Fan
Secure the Rain Sensor On TopFeed the Rain Sensor ThroughClean the KnockoutLocate the “T” Shaped Knockout
9 118
7 7b 7d
5e
STEP 6 & 6b. APPLY BUTT CONNECTORS TO CUT POWER SUPPLY LEADS 2”(approx.) FROM
STRAIN RELIEF KNOTS (6a). MODIFY LENGTH OF WIRES (as needed) ON THE NEW UPGRADE
ASSEMBLY, STRIP ENDS, INSERT TO APPLIED BUTT CONNECTORS AND CRIMP (6b). *NOTE: IF
PREVIOUS POSITIVE POWER SUPPLY WAS DISCONNECTED FROM THE FUSE HOLDER VIA A
FEMALE CLIP, YOU DO NOT NEED TO INSTALL A BUTT CONNECTOR ON THE POSITIVE POWER LEAD
(use original connector and swap out with attached power lead on the new fuse holder).
POSITIVE POWER SUPPLY LEADS WILL BE BLACK OR RED 16 GAUGE WIRES.
6
STEP 7 IS FOR KITS WITH A RAIN SENSOR...
7c
6b
Hook Up PowerApply Butt Connectors
STEP 5e. CONNECT THE
WHITE LEAD w/BULLET CON-
NECTOR ON YOUR NEW UP-
GRADED SCREEN ASSEMBLY
TO THE DOME SWITCH IN THE
BASE. PLUG IN SECURELY.
Connect to Dome Switch *
NOTE: Swap Power Leads
*

3
ATTENTION: If you have a black canister style motor (FIG. A) be sure to have a control board jumper installed on the
circuit board as illustrated below. If your fan uses a flat pancake style motor (FIG. B) be sure to remove the control board
jumper.
FIGURE B.
Flat Pancake Style Motor
FIGURE A.
Black Canister Style Motor
How to Install Jumper on to a Fan main control board
Allows use of control board with Canister Fan Motors
Step 1
Jumper
Control board
Jumper terminals
Fan main
control board
Step 2
Install Jumper onto both
terminals on the Fan main
control board
Step 3 Completed install
If you have any questions regarding installation or operation of any Fan-Tastic Vent product please,
feel free to contact us toll free at 800-521-0298 Monday through Friday 8:00 a.m.—5:00 p.m. EST.
Can Motor Pancake Motor