F&F DRM-02 User manual

F&F Filipowski sp. j.
Konstantynowska 79/81 95-200 Pabianice
phone/fax: [phone] POLAND
http://www.fif.com.pl e-mail: [e-mail]
MICROWAVE MOTION DETECTOR
Do not dispose of this device to a garbage bin with other unsorted waste!
In accordance with the Waste Electrical and Electronic Equipment Act
any household electro-waste can be turned in free of charge and in any
quantity to a collection point established for this purpose, as well as to the
store in the event of purchasing new equipment (as per the old for new rule,
regardless of brand). Electro-waste thrown in the garbage bin or abandoned
in the bosom of nature pose a threat to the environment and human health.
DRM-02
WARRANTY. The F&F products are
covered by a warranty of the 24 months
from the date of purchase. Effective only
with proof of purchase. Contact your
dealeror directly with us. More
information how to make a compliant can
be found on the website:
www.fif.com.pl/reklamacje
5 908312 593966
- 3 - - 4 -
- 2 -
- 1 -
Purpose
The motion detector is used for automatic, temporary lighting attach
if a person or another object appears in detector’s range in places such
as hallways, courtyards, approaches and driveways, garages, etc.
Microwave sensor allows for motion detection by wooden boards,
plasterboard panels, glass and plastics.
Functioning
DRM sensor emits and bounces high-frequency 5.8 GHz electromagnetic
waves. The sensor detects changes in the reflected waves caused
by movement of the object in the area of detection. The sensor detects
movement of an object to and from the sensor. Movement in the range
of detection will automatically attach the lighting for time set by the user.
After this time the lights will be turned off automatically. The motion sensor
is equipped with light dependant relay able to attaching lighting during
the day. Detection status and standby to attach lights are activated only after
dusk. Sensor activation time might be adjust by the user.
In addition, there is a possibility of adjustment of the detection area in range
3-10 m (for h= 2.5 m) and the receiver actuation time adjustment
to 8 s ÷ 12 min. The inclusion of the receiver is signaled by a shining green LED.
Sensor can work indoors. The sensor allows for motion detection by wooden
boards, plasterboard panels, glass and plastics. Temperature changes do not
affect on motion detection
ATTENTION!
The power of microwave radiation is relatively low and is completely safe for
humans and animals. Its value is less than 10 mW. By comparison,
microwaves and cell phones radiate about 1000mW of power (100 times
harder).
Ç
R
?
Ç
Detection range
Radius of the sensor detection can be adjusted in the range from
2 m to 10 m (the parameters for the sensor mounted at a height
of 2.5 m). Rotate the knob to the right [max] increases the area of
a field of detection, rotate left [min] reduces the area of the field
detection.
Actuation time
Receiver’s actuation time can be adjusted between 8 s for 12 min.
Rotate knob to the right [max] increases ON time, rotate left [min]
reduces the attached time. After a set time receiver is turned off
automatically.
Sensitivity of light dependant relay
Sensitivity of light dependant relay can be adjusted in
range from 2 Lx to 2000 Lx. Rotate the knob toward to the „moon”
sign - attached later, rotation to the „sun” sign - attached earlier.
In order to sensor was active throughout the day, set the knob
maximally toward the „sun”.
Settings
Technical data
supply 230V AC
current load <5A
frequency of the microwaves radiation 5,8GHz
power radiation <10mW
detection range 360°
detection ray - adjustable (for h=2,5m) 1÷10m
activation treshold - adjustable 2÷2000Lx
receiver’s activation time - adjustable 8s÷12min.
activation delay 1s
connection screw terminals 1mm
working temperature -25÷50°C
dimensions 42mm
power consumption 0,9W
fixed two screws to the substrate
protection level IP40
²
Ø103 h=
Assembly
Device assembly
1. Unscrew the outer shield of the detector. Unscrew the two screws and
remove the sensor cover (Pict. 1).
2. Disconnect the power.
3. Wires provide throughout eyelet rubber in mounting base of the sensor.
4. Basis with two screws attached to the substrate.
5. Connect according to schema.
6. Set area of detection, set the sensitivity of the light dependant relay and
activation time.
7. Assemble the sensor’s cover housing
(Pict. 2).
(Pict. 3).
Wiring diagram
L
N
N
L
L'
DRM
Pict. 1
Pict. 3
Pict. 2
D150629

X-ON Electronics
Largest Supplier of Electrical and Electronic Components
Click to view similar products for Photoelectric Sensors category:
Click to view products by F&F manufacturer:
Other Similar products are found below :
7442AD2X5FRX EX-19B-LP 7443AR0X5FRX 7452AD4D4NNX F3WD052C5M 76402600100 7642AD-04-N-2-2-NX 7655AR-04-F-1-2-
RX 7694ADE04DS2X FE7C-FRC6S-M PM-R24-R Q45VR2FPQ 13104RQD07 MP-D70P-100-240V MQ-D30A-DC12-24V
E3JUXM4MN E3L2DC4 E3S3LE21 E3SCT11M1J03M E3SDS20E21 E3VDS70C43S E3XNM16 BR23P HOA6563-001 OJ-3307-30N8
OS-311A-30 P32013 P34036 P43004 P56001 P60001 PB10CNT15PO S14132 935286-000 S52101 S56258 SH-21E FD-SN500 FE7B-
FDRB6-M SU-79 T36342 T40300 T60001 PD60CNX20BP FX2-A3R FX-302-HY PM-T64W PX-22 PZ2-51P CX-491-P-J