Fanimation Multimax FP8008CH User manual

OWNER’S MANUAL
READ AND SAVE THESE INSTRUCTIONS
Be mindful of all warnings shown throughout
Model No. FP8008CH
The Multimax
Ceiling Fan
Net Weight 20.5 lbs (9.3 kgs)

Canopy
Fan assembly
Blades
Mounting Bracket
Downrod
1.Unpack and inspect fan carefully to be certain all contents are
included.
OFF OFF OFF
Turn off power at breaker
box to avoid possible
electrical shock.
Use metal outlet box
suitable for fan support.
Secure outlet box directly to
the building structure using
wood screws (included).
Outlet box must support
50 lbs min.
2.
3.
Glass
6. Blade installation
Deco Ring
Deco Cap
Upper Housing
Hardware bag
P2
Remote Control
Gu24 Bulb x 2
Blade Screw w/Washer 9pcs
Nylon Washer 9pcs
Mounting Screw 2pcs
Spring Washer 2pcs
Lock Washer 2pcs
Wood Screw 2pcs
Star Washer 2pcs
Blade Balance Kit 1pc
Wire Nuts 4pcs
Upper Housing Screw 2pcs
Safety Cable Bag 1pc
5.
Outlet Box
Mounting
Bracket
Screw
Blade
Nylon Washer
4.
To attach ceiling support cable, drill a ¼ in. pilot
hole, located independently from the junction
box, into the ceiling joist or structural member.
Securely attach the ceiling support cable with
3⁄8 in. x 2 in. lag bolt and flat washer.
MUST be able to fully support at least 100 lbs.
Install mounting
bracket to Outlet box
in ceiling using washers
and the mounting
screws provided with
the outlet box.
Do not use
existing
mounting
bracket,
replace it with
new mounting
bracket from
box.
Attach blades to fly wheel
with blade screws and nylon
washers provided in the
hardware bag. Make sure
blade numbers (2, 3 or 4
Blades) correspond with
figures shown on flywheel.
Screw Driver

7. Upper Housing & DownrodAssembly
(1)
Feed motor lead wires and safety cable
through Upper Housing,Deco Ring, Canopy
and downrod and insert downrod into yoke.
Upper Housing
Downrod
Wires & safety cable
Yoke
Cotter Pin
Cross Pin
(2)
Insert the cross pin through Yoke & Downrod and
secure with Cotter Pin.
(3)
Tighten both Downrod Set Screws to further
secure Downrod, then pull down the Upper
Housing to cover wiring Pan.
Downrod Set Screw
Yoke
Cotter Pin
(4)
Attach Upper Housing to brackets on Wiring Pan.
Align rectangular hole with reversing switch, and
secure with 2 screws provided from hardware bag.
8. Hanging the fan
Mounting
Bracket
(1)
Lift fan assembly onto mounting bracket.
(2)
Rotate fan so that the groove on the ball engages
the ridge in the mounting bracket.
P3
Deco Ring
Deco Ring
(3)
Ridge
Ball Groove
Mounting
Bracket
Safety cable
Canopy
Attach the safety cable to ceiling support cable. Slide cable
clamp onto safety cable (from fan). Place the end of cable
through the loop of ceiling support cable. Pull as much cable
through loop as possible. Feed end of cable into clamp hole
and firmly tighten screw. Cut off excess safety cable.
Safety Cable
Ceiling Support
Cable
Screw
Screws
Yoke cover
Screws
Reversing
Switch
Cable Clamp

P4
Black White
White
Black
Blue
9. Make wire connection-( for 100~127VAC/60Hz )
-for Remote Receiver
From House From Fan
From Remote
Black
( AC - L )
White
( AC - N )
Green
( for ground wire )
White
( Motor - N )
Black
( Motor - L )
Blue
( for light kit )
( from downrod )
Yellow Green
9-1. Connect black wire from house to black wire from Receiver and secure with wire nut.
9-2. Connect white wire from house to white wire from Receiver and secure with wire nut.
9-3. Connect green wire from house and green wires from fan and secure with wire nut.
9-4. Connect white wire from Receiver to white wire from fan and secure with wire nut.
9-5. Connect blue wire from Receiver and blue wire from fan and secure with wire nut.
9-6. Connect black wire from Receiver and black wire from fan and secure with wire nut.
9-7. Slide the receiver unit into the open
end of the mounting bracket
Yellow Green
10. Install the canopy
( from mounting bracket )
Ribs
Glass
11.Attach the Light Kit:
(Note: Be sure power is off befor
e proceeding)
11-1:
Attach lamp to lamp-holder.
11-2:
Attach glass shade onto fan by turning
clockwise.Don’t over tightened.
1. Push up the Canopy until the two
screws on mounting bracket are
engaged with Key Holes in
canopy.
2. Rotate the canopy slightly until
the two screw heads are in the
small end of the Key Holes.
3. Tighten both screws.
4. Push Deco Ring up to Canopy,
align holes on Canopy with ribs on
Deco Ring, and push “snap-in”.
Canopy
Key Holes
Deco
Ring
Receiver Unit
Mounting
Bracket

P5
13. Establish connection between your hand-held remote and
your fan
Screws
12-1:
Detach light kit from fan housing by loosening
3 screws.
12-2:
Detach terminal connectors
from light kit and fan.
12-3
Just attach Deco Cap to bottom of fan by “Snap - in”.
12. Fan Installation without light kit:
Wires
Deco Cap
WiresWires
13-1. Restore power to your ceiling fan at the breaker box and/or wall switch.
13-2. Within 60 seconds of restoring power to your fan, press and hold the small button on the
back of your hand-held remote control using a pen or other pointed object until the fan
motor turns on and the fan blades begin moving.
13-3. Your fan receiver and remote are now synced and your fan is ready for normal operation.
Button

Parts List
Model No. FP8008CH
Reference #
1
3
2
4
5
6
7
9
8
10
11
12
14
Description Part #
Hanger Bracket Assembly w/Screws
Ball-Downrod Assembly
Canopy - Ceiling
Canopy Screw Cover
Housing Upper Asm
Fan Motor Assembly
Light Kit Assembly
Decorative Lower Housing Cover
Light Bulb - Gu24 CFL 18W Low Profile
Glass
Blade Set (4)
Transmitter - Touch Screen
Bag Assembly, Loose Parts
APGFF110BL
ADRFF-6CH
P800801CH
P800802CH
AP800803CH
AMA8008CH
AP800810CH
P800809CH
PPGU24C18
P8008130P
AP800806**
TRL8TS
13 Receiver RECAN54
HDWFP8008CH
**Insert FINISH CODES (Refer to fan model number located on downrod support)
Before discarding packaging material, be certain all parts have been removed.
HOW TO ORDER REPAIR PARTS
When ordering repair parts, always give the following information:
Part Number
Part Description
Fan Model Number
Contact your retail store for repair parts.
P6
15 Screw Driver PSCDR15

P7
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
NOTE:Theillustrationshownisnottoscaleoritsactualconfigurationsmayvary.

Copyright 2010 Fanimation /0 10102
10983 Bennett Parkway
Zionsville, IN 46077
Toll Free [phone]
FAX [phone]
Outside U.S. call [phone]
Visit Our Website @ www.fanimation.com