Fanimation Punkah FP720 Series User manual

Copyright 2008 Fanimation, Inc.
2008/05
10983 Bennett Parkway
Zionsville, IN 46077
Toll Free [phone]
FAX [phone]
Outside U.S. call [phone]
Visit Our Website www.fanimation.com
The Punkah®Wall Mount Assembly
Wall Assembly Specifications
A Support Spacing 12˝to 4´ *
B Fan Base Width 4½˝
C Blade Projection 21˝with 18˝Blades@30°
24˝with 22˝Blades@30°
D Blade Projection 9½˝with 18˝Blades
11¾˝with 22˝Blades
EBlade Angle
(10° increments)
Wide Oval Blade, 30° max
Narrow Blade, 45° max
F Motor Assembly Unit 13¾˝L x 7¼˝W
Weights (Approximate)
Fan Assembly Unit 5 lbs
Motor Assembly Unit 17½ lbs
B
A
D
C
E
F
F
NOTES: Installation is NOT recommended for
sound sensitive areas.
*For spacing of 12˝to 27½˝cutting
push rods is required.
Not designed for significant air movement.
Not recommended for Damp Location.
Dimensions shown in inches
SPECIFICATION SHEET
Product Specifications subject to change
The Punkah®
FP720 - Ceiling/Wall Unit / FP780 - Motor

Weights (Approximate)
Fan Assembly Unit 5 lbs
Motor Assembly Unit 17½ lbs
**Available Finishes
AB Antique Brass
PW Pewter
RS Rust
Ordering Information (Items Priced and Sold Separately)
Item Catalog No. Description
Fan Assembly Unit FP720** Use in ceiling or wall application
One push rod included (with each fan unit)
One Motor Unit FP780**
120V, 60 Hz, ½ horsepower, 0.90 amp, 19 rpm,
single-speed; ON/OFF Switch (user supplied) only.
2 ft power cord (or can be hard-wired directly)
Maximum 6 Fan Assembly Units per Motor.
Blade Sets
(Order Separately)
See catalog for other blade options
NOTE: 18˝blades are recommended for most
installations
220V Model (Export version)
Motor Assembly - 220 volt, 50 Hz
Ceiling / Wall Mount
Oscillating RPM: 19 (single-speed)
Available in 3 standard finishes
NOTES: Installation is NOT recommended for sound
sensitive areas.
*For spacing of 12˝to 27½˝cutting
push rods is required.
Not designed for significant air movement.
Not recommended for Damp Location.
C
B
A
D
E
F
Dimensions shown in inches
**Insert Finish Codes
The Punkah®Ceiling Mount Assembly
Ceiling Assembly Specifications
A Overall Length 4´ to 24´
B Support Spacing 12˝to 4´
C Fan Base Unit 4½˝L x 4½˝W
D Overall Drop 23˝with 18˝Blades
27˝with 22˝Blades
E Blade Sweep 21˝with 18˝Blades
25½˝with 22˝Blades
F Motor Assembly Unit 13¾˝L x 7¼˝W
C
F
NOTE: Motor may also
be wall mounted
or mounted between
fan assemblies
INSTALLATION REQUIREMENTS
It is recommended that each fan and the motor have ¾˝plywood backing (12˝x12˝min.)
snug behind the sheet rock for adequate support. This may also be done with continuous
backing running the length of the fan system thus allowing the most flexibility in placing
the blades.
ELECTRICAL REQUIREMENTS
A 120 VAC electrical feed is required and should be accessible to the
center of the motor. This circuit should be wired to an on/off switch
(Motor is single speed). The motor assembly is supplied with a 2 ft.
cord with plug. Motor assembly may be wired directly to electrical
outlet box. The Fan Blades oscillates at approximately 18-20 rpm.