Fantasea Line RADIANT 1000X User manual


Fantasea Radiant 1000X Dive & Video Light Instruction Manual 20151228
Fantasea Line
RADIANT 1000X
Video & Dive Light
(Cat. No. 6050)
Instruction Manual


Fantasea Radiant 1000X Dive & Video Light Instruction Manual 20151228
TABLE OF CONTENTS
TABLE OF CONTENTS................................................................................................................. 2
DISCLAIMER............................................................................................................................... 3
INTRODUCTION ......................................................................................................................... 3
GENERAL INFORMATION....................................................................................................... 3
SPECIFICATIONS..................................................................................................................... 4
IDENTIFICATION OF RADIANT 1000X PARTS............................................................................. 4
INSTRUCTIONS FOR USE............................................................................................................ 5
INSTALLING & REMOVING BATTERIES .................................................................................. 5
TURNING THE RADIANT 1000X LIGHT ON/OFF..................................................................... 7
MOUNTING THE RADIANT 1000X LIGHT ON AN ARM .......................................................... 8
CARE & MAINTENANCE............................................................................................................. 9
FANTASEA PRODUCTS CONSUMER LIMITED WARRANTY ...................................................... 10


Fantasea Radiant 1000X Dive & Video Light Instruction Manual 20151228
DISCLAIMER
While every effort has been made in order to ensure that the information included in this
instruction manual is accurate and complete, no liability will be accepted for any errors or
omissions. Fantasea Line reserves the right to change product specifications and features described
herein at any time without prior notice. No part of this instruction manual may be copied,
translated or reproduced without the prior written permission of Fantasea Line. Fantasea Line
makes no warranties aside from limited product warranty as described at the end of this manual.
INTRODUCTION
GENERAL INFORMATION
The Radiant 1000X Light is a compact, durable and powerful dive and video light, designed to
enhance color and light in underwater videos and still images.
Featuring a compact design and durable construction, the Radiant 1000X Light can be
comfortably integrated into any underwater photo system, such as with action cams, amphibious
cameras, compact digital housings and more.
A battery power indicator light around the power switch enables easy monitoring of the battery
power. The light makes use of 2 powerful LEDs, which provide an ultra bright, even and wide
output. A wide beam angle of 120 degrees makes the Radiant 1000X suitable for lighting a wide
range of compositions. Color temperature of the beam is warm and assists with producing vivid and
colorful videos and still images without having to use any color correction filters. A 3-level
adjustable power output allows you to control the intensity of the light for various compositions
and diving conditions, as well as extending the burn time of the light (the batteries will provide
power for a considerably longer time when the light is set at lower intensity settings such as 50% or
25%). The red light mode is perfect for sneaking up and focusing on shy creatures. The two flashing
modes can serve for signaling purposes and SOS situations, providing a helpful burn time of over 8
hours in these modes (assuming the batteries are fully charged). 
return the light to the same setting as previously used before the light was last turned off.
Depth rated to 100 meters/330 feet, the Radiant 1000X Light fulfills the needs of both
recreational and technical divers.
Note
Please read this manual carefully in order to properly operate the Radiant 1000X Light.
Store this manual in a safe place for further reference once you have read it.


Fantasea Radiant 1000X Dive & Video Light Instruction Manual 20151228
SPECIFICATIONS
Depth ratio
100 meters / 330 feet
Maximum output
1000 lumens
Beam angle
120 degrees
Material
Aluminum head, Polycarbonate body
Battery
1 x 18650 Li-ion battery
Burn time
60* minutes at 100% power
* in optimal conditions
LED Lifespan
30,000 hours
Color temperature
5,000~7,000K
Operation modes
100% / 50% / 25% power / red light/ flashing / SOS
Battery power indicator
Green (100%-60% power)
Yellow (60%-30% power)
Red (30%-15% power)
Flashing Red (15%-1% power)
Dimensions
30.5 x 121 mm / 1 ¼ x 4 ¾ inch (diameter x length)
Weight
85g (without batteries)
IDENTIFICATION OF RADIANT 1000X PARTS
LED head
Power button
Battery indicator light
YS Connector
Hand Lanyard Insert Slot
2
4
1
3
2
1
2
2A
3
4
1
3
4
2A
2


Fantasea Radiant 1000X Dive & Video Light Instruction Manual 20151228
INSTRUCTIONS FOR USE
INSTALLING & REMOVING BATTERIES
1. Please read the following information and warnings prior to purchasing and installing
batteries inside the Radiant 1000X Light:
a. Only an 18650 rechargeable 3.7-volt Li-Ion battery should be installed inside the
light.
b. The Radiant 1000X Light should only be operated using quality brand batteries, such
as those supplied by Fantasea Line. Poor quality 18650 batteries might damage the
light, negatively affect its performance and will void the warranty.
c. Make sure that the 18650 batteries you install inside the light feature a protective
circuit board (PCB). 18650 batteries with a protective circuit board are also known
as 19670. The batteries included with the light feature a PCB.
d. Warning! Under no conditions should CR123 batteries or any batteries other than a
protected 18650 battery be used in this light.
e. Warning! Lithium-ion batteries can explode or cause a fire if they are used
incorrectly or if they are defective. READ THE FOLLOWING CAREFULLY!
Always carefully check each battery BEFORE using to ensure that the
protective seal is undamaged and intact. If in doubt, DO NOT use or recharge
the battery. Dispose it at a proper disposal facility.
Always handle the battery with care. Do not drop lithium-ion batteries!
Store the battery in a safe and dry place and keep the battery away from all
metal objects.
Never expose the battery to temperatures above 100 degrees Celsius.
Only use chargers that have specially been designed for use with lithium-ion
batteries.
When charging batteries, keep the charger away from highly flammable
materials or products.
Please follow any additional guidelines, instructions or restrictions that are
included with the batteries.
2. To open the Radiant 1000X Light, hold the hand grip firmly in one hand with the hand grip
pointing towards your body and the LED head pointing away. Turn the LED head clockwise
until it separates (image #1 on the following page). Gently separate the LED head from the
body of the light (image #2 on the following page).


Fantasea Radiant 1000X Dive & Video Light Instruction Manual 20151228
3. Install or remove an 18650 Li-ion battery inside the body of the light. Note that the battery
should be installed with its positive end (button end) pointed toward the LED head (image
#3).
4. Reinstall the LED head on the body of the light, carefully aligning it with the thread on the
body of the light and tightening it evenly in a counterclockwise fashion all the way to the
end (image #4). Do not use force and do not allow it to screw down unevenly.
Image #1
Image #2
Image #4
Image #3


Fantasea Radiant 1000X Dive & Video Light Instruction Manual 20151228
5. It is recommended that you occasionally remove the black O-ring seals from the light,
wipe them with a soft, clean cloth and lubricate them with a small drop of silicone grease.
Then carefully replace the O-ring prior to replacing the LED head.
6. The hand lanyard can be easily removed and reinstalled as needed. To install the Hand
Lanyard, insert it through the Hand Lanyard Insert Slot on the back of the light, then pull it
through itself and test it in order to make sure it is secure.
TURNING THE RADIANT 1000X LIGHT ON/OFF
1. To turn the light on, hold down the power button for 1.5 seconds.
2. Take special care not to stare into the light beam or shine it into the eyes of anyone else,
because the light is powerful and may damage ones’ eyes.
3. The Radiant 1000X Light features 6 power output modes in the following order: 100%
power output, 50% power output, 25% power output, red light, flashing light and SOS. To
switch between the power output modes, simply push the power button for half a second.
Each time the power button is shortly pushed, the power mode is altered according to the
order of power modes as listed above.
4. To turn the light off, press the power button for 2 seconds. The light will flash three
times and then shut off.
5. The following diagram outlines the operation of the Radiant 1000X Light:
POWER OFF
PUSH & HOLD BUTTON FOR 1.5 SEC
100% POWER
50% POWER
25% POWER
RED LIGHT
PUSH & HOLD BUTTON FOR 0.5 SEC
PUSH & HOLD BUTTON FOR 0.5 SEC
PUSH & HOLD BUTTON FOR 0.5 SEC
PUSH & HOLD BUTTON FOR 0.5 SEC
PUSH & HOLD BUTTON
FOR 2 SEC
FLASHING MODE
SOS MODE
PUSH & HOLD BUTTON FOR 0.5 SEC


Fantasea Radiant 1000X Dive & Video Light Instruction Manual 20151228
5. When the Radiant 1000X Light is turned on, the colorful light around the power switch
button serves as a battery indicator and shows the battery charge level:
a. Green (100%-60% power)
b. Yellow (60%-30% power)
c. Red (30%-15% power)
d. Flashing Red (15%-1% power)
MOUNTING THE RADIANT 1000X LIGHT ON AN ARM
1. The Y-S Connector included enables mounting the Radiant 1000X Light on any arm or
connector that features a standard YS Mount at the top, such as on Fantasea Flex Arms.
2. In order to install the Y-S Connector on the Radiant 1000X Light, first remove the screw
from the bottom of the YS Mount by unscrewing it all the way out (image #5).
3. Remove the LED head. To do so, hold the hand grip firmly in one hand with the hand grip
pointing towards your body and the LED head pointing away. Turn the LED head clockwise
until it separates. Gently separate the LED head from the body of the light (images #1 and
#2 on page 6). 
installation of the Y-S Connector.
4. Install the Y-S Connector by sliding it on the body of the light, starting from its front and all
the way towards the rear end until it reaches a higher rib and can no longer be slid
backward (image #6). Note that the connector is flexible and might need to be expanded a
bit in order to be slid on the body of the light.
5. Reinstall the battery and the LED head on the body of the light, carefully aligning it with
the thread on the body of the light and tightening it evenly in a counterclockwise fashion
all the way to the end (images #3 and #4 on page 6). Do not use force and do not allow it
to screw down unevenly.
6. With the Y-S Connector installed on the light, position it over the arm so that the Y-S
Mount on top of the arm is aligned with the YS Connector at the bottom of the LED light
(image #7 on the following page).
7. Install the screw all the way through the Y-S Connector and Y-S Mount on the arm (image
#8 on the following page). Tighten it enough to keep the LED light in a fixed position.
8. It is always advisable to secure the light using the hand lanyard.
Image #5
Image #6
Higher rib


Fantasea Radiant 1000X Dive & Video Light Instruction Manual 20151228
CARE & MAINTENANCE
1. After each dive, carefully soak and rinse exterior components in fresh water.
2. Visually examine the two O-ring seals found below the threads of the body of the light prior to
replacing the LED head. Any sand, dust or hair lines must be removed from this area in order to
ensure a perfect watertight seal.
3. In case of a damaged O-ring, replace it with a replacement O-ring. After an O-ring replacement has
been made and the light has been reassembled, make sure to test the watertight seal of the light
prior to diving with it. Simply soak the light in shallow water, making sure no bubbles are escaping
from it and that no water is entering the light.
4. Store the Radiant 1000X Light in a protected, dry and shaded area.
5. Remove the battery when storing the LED light for an extended period of time.
6. The Radiant 1000X Light should only be operated using quality brand batteries, such as those
supplied by Fantasea Line. Poor quality 18650 batteries might damage the light, negatively affect
its performance and will void the warranty.
7. Avoid disassembling any parts of the light other than removing the LED head from the body so that
batteries can be installed and removed. Do not attempt to disassemble the LED head.
8. There is never a need to use force when removing or reinstalling the LED head to the body of the
light or to turn the light on or off. If force is required then that is an immediate indication that
something is not right.
Image #7
Image #8


Fantasea Radiant 1000X Dive & Video Light Instruction Manual 20151228
FANTASEA PRODUCTS CONSUMER LIMITED WARRANTY
Fantasea Line warranties this product against defects in materials and workmanship under reasonable use
for a period of ONE (1) YEAR, (two years, where required by law as determined by the origin of the
authorized dealer). This warranty is effective from the date of retail purchase from Fantasea or an
authorized Fantasea dealer, by the original end-
cover any commercial use of the product. If a product defect arises and a valid claim is received within the
Warranty Period, at its option, Fantasea, or its authorized service facilities will either (1) repair the product
defect at no charge, (2) exchange the product with a product that is new or which has been manufactured
from new or serviceable used parts and is at least functionally equivalent to the original product. The
warranty will not extend beyond the original warranty period.
Your Fantasea Product should be registered within 30 days of purchase. You must keep the proof of
purchase which indicates the date on which the purchase was made; as you may be required to show proof
of purchase if you need warranty service. The following conditions apply: 1. This warranty extends to the
original purchaser only. It is not assignable or transferable. 2. The warranty does not cover damage resulting
from misuse, abuse, negligence, or accidents. Proper maintenance of the Product is the responsibility of the
owner. 3. The warranty does not cover damage directly or indirectly resulting from the use of unauthorized
replacement parts or service performed by unauthorized facilities. 4. This warranty does not cover any
damage to any other product used in conjunction with the Fantasea product, including cameras and lenses,
and resulting from any defect in the product materials or workmanship. 5. The cost of sending the product
back to Fantasea or its authorized service facilities is the responsibility of the customer. 6. The warranty does
not cover any incidental damages resulting from any defects in the product. This expressly includes any
tr
conditions of this warranty are expressly in lieu of all other expressed warranties, including the payment of
consequential or incidental damages for the breach of any warranty. Please register your product on line at
this URL: http://www.fantasea.com/registration.
www.fantasea.comor visit our [e-mail] further information, please contact us at