Fantasea BigEye Lens S95 User manual

1
EyeGrabber Canon G Series Instruction Manual 20110615
Fantasea EyeGrabber Canon G Series
(Cat. No. 4054)
Instruction Manual
The EyeGrabber Canon G Series allows for secure storage of Fantasea accessory lenses and filters when not installed
on the housing.
Compatible with the Following Lens Accessories:
BigEye Lens G Series (Cat. No. 5135)
BigEye Lens S90/S95 (Cat. No. 5139)
EyeDaptor G Series-F67 (Cat. No. 4701) - with any lens accessory mounted on top of the adaptor
EyeDaptor S90/S95-F67 (Cat. No. 4710) - with any lens accessory mounted on top of the adaptor
RedEye Filter G Series (Cat. No. 5201)
PinkEye Filter G Series (Cat. No. 5303)
RedEye Filter S90/S95 (Cat. No. 5305)
PinkEye Filter S90/S95 (Cat. No. 5307)
SharpEye Lens M67 (Cat. No. 5128) - only when mounted on top of the EyeDaptor G Series-F67 (Cat. No.
4701) or the EyeDaptor S90/S95-F67 (Cat. No. 4710)
Using the EyeDaptor G9-G10 (Cat. No. 4703) or the EyeDaptor S90/S95-G Series (Cat. No. 4707) with any of
the lens accessories mentioned above, still allows mounting these lens accessories on the EyeGrabber
Any of the lens accessories mentioned above can still be mounted on the EyeGrabber when color correction
inserts are installed inside
Please note that this EyeGrabber is not compatible with the RedEye Filter G7/G9 (Cat. No. 5203)
Included in the Kit:
Instructions for Use:
1. Assembling the EyeGrabber Lens Holder on a Flex or Ball & Joint Arm
a. Please use the utmost care and do not use excessive force when assembling and disassembling the different
accessories, in order to not cause any damage to the products.
b. It is advisable to mount the EyeGrabber on the arm prior to installing the arm on the housing tray or handle.
c. Remove the screws from the T2 Connector so that the two parts of the T2 Connector are disconnected. Please
note that there are two sets of screws included in the kit. The type of screws compatible with your arm
depends on the model of the arm. In general, longer screws are compatible with wider arms, such as Fantasea
T2 Connector
Set of 2 shorter screws
EyeGrabber Canon G Series

2
EyeGrabber Canon G Series Instruction Manual 20110615
Flex arms, while shorter screws are compatible with narrower arms, such as Ball & Joint arms. Choose the
proper set of screws for your system and leave the screws installed only inside the front part of the T2
Connector (image #1). Keep the other set of screws in storage for future use, in case you replace the arms used
in your system.
d. If assembling the EyeGrabber on a Flex arm, gently rotate the links of the
arm so that two sequential holes positioned on the upper half of the arm
are aligned in a way that enables inserting screws inside (image #2). If
assembling the EyeGrabber on a Ball & Joint arm, simply choose two slots
on the upper half of the arm which the EyeGrabber will be assembled
through.
e. Hold the front part of the T2 connector with the two screws installed inside in front of the arm, so that the
screws are aligned with the two holes or slots in the arm. Insert the screws through the holes or slots of the
arm (image #3). Any resistance encountered might be due to improper alignment of the holes on the Flex arm
or due to the resistance of the Nylon support line found inside the Flex arm. In such a case, please repeat step
1c and make sure the support line doesn’t get in your way.
f. Hold the rear part of the T2 Connector on the other side of the arm, so the narrow side of it is facing the arm
and aligned with the screws (the flared side with conical holes should be facing outward). Insert the screws
into this part of the connector as well and tighten them until both sides of the T2 Connector are stable on the
arm (image #4). If the screws are too short to reach the end of the rear connector, replace them with the set
of longer screws. If the screws are too long and stick out from the back of the connector, replace them with
the set of shorter screws.
Image #1
Image #2
Image #3
Image #4

3
EyeGrabber Canon G Series Instruction Manual 20110615
g. Hold the lens holder against one of the sides of the T2 Connector
attached to the arm, so that the lens holder is facing out of the
arm and the lens holder’s connector is aligned with the T2
Connector. Make sure that you attach the lens holder on the T2
Connector that faces outward from the housing, so you will have
more space to mount the lens on the EyeGrabber. Slide the lens
holder on the T2 Connector and tighten the screw on the lens
holder in order to fix its position (image #5). It is important to
ensure that the lens holder connector and the T2 Connector are
perfectly aligned prior to tightening the screw, or else the lens
holder cannot be stabilized on the arm.
h. Install the snap cord of the accessory lens on the arm. If you had
the snap cord attached to the housing before, remove it and
install it on the arm instead, so the accessory lens can be secured
when mounted both on the housing lens port and the
EyeGrabber.
i. Mount the arm, with the EyeGrabber installed, on your housing tray or handle.
2. Installing and Removing Lens Accessories from the EyeGrabber
a. Installing and removing lens accessories from the EyeGrabber during
the dive is the same as when installing and removing from the
housing lens port. In order to install the lens accessory on the
EyeGrabber, first hold it in your hand so it is aligned with the
EyeGrabber (image #6). Place the lens over the EyeGrabber and
follow by securing the four bungee cords to the slots featured at the
back of the EyeGrabber diagonally (image #7). Please note that the
lanyards are essential in order to keep the lens accessory in place.
Make sure that the accessory lens is properly mounted on the
EyeGrabber by gently trying to pull it out. If properly installed, the
lens should not easily come off the EyeGrabber.
b. It is recommended not to detach the secure line from the accessory
lens during the dive, whether if mounted on the arm or on the
housing lens port.
c. In order to remove the accessory lens from the
EyeGrabber, start by detaching the lens lanyards from
the EyeGrabber and follow by removing the accessory
lens from the EyeGrabber.
d. After the dive, detach the lens accessory from the
EyeGrabber and rinse all components in fresh water.
Dry with a soft clean cloth and store safely.
Image #5
Image #6
Image #7

4
EyeGrabber Canon G Series Instruction Manual 20110615
Fantasea Product Consumer Limited Warranty:
“Fantasea” warrants this Fantasea Line branded product against defects in materials and workmanship under
reasonable use for a period of ONE (1) YEAR, (two years, where required by law as determined by the origin of
the authorized dealer). This warranty is effective from the date of retail purchase from Fantasea or an
authorized Fantasea dealer, by the original end-user purchaser (“Warranty Period”). This warranty does not
cover any commercial use of the product. If a product defect arises and a valid claim is received within the
Warranty Period, at its option, Fantasea, or its authorized service facilities will either (1) repair the product
defect at no charge, (2) exchange the product with a product that is new or which has been manufactured
from new or serviceable used parts and is at least functionally equivalent to the original product. The warranty
will not extend beyond the original warranty period. Your Fantasea Product should be registered within 30
days of purchase. You must keep the proof of purchase which indicates the date on which the purchase was
made; as you may be required to show proof of purchase if you need warranty service. The following
conditions apply: 1. This warranty extends to the original purchaser only. It is not assignable or transferable. 2.
The warranty does not cover damage resulting from misuse, abuse, negligence, or accidents. Proper
maintenance of the Product is the responsibility of the owner. 3. The warranty does not cover damage directly
or indirectly resulting from the use of unauthorized replacement parts or service performed by unauthorized
facilities. 4. This warranty does not cover any damage to any other product used in conjunction with the
Fantasea product, including cameras and lenses, and resulting from any defect in the product materials or
workmanship. 5. The cost of sending the product back to Fantasea or its authorized service facilities is the
responsibility of the customer. 6. The warranty does not cover any incidental damages resulting from any
defects in the product. This expressly includes any travel reimbursements or any other costs associated with
the purchaser’s optional use of the product. The conditions of this warranty are expressly in lieu of all other
expressed warranties, including the payment of consequential or incidental damages for the breach of any
warranty. Please register your product on line at this URL: http://www.fantasea.com/registration.
www.fantasea.com/contactFor further information, please contact us at
www.fantasea.comor visit our website