Fast & Fluid Management SO-300 User manual

FAST &FLUID MANAGEMENT srl
AUnitofIdexCorporation
ShakerSO-300
USERMANUAL
FAST&FLUIDMANAGEMENTSrl
AUnit ofIDEXCorporation
ViaPelizzadaVolpedo, n°109/111
20092CiniselloBalsamo(MI)
ITALY
Tel.:[phone]
Fax:[phone]
Web:www.fast-fluid.com

FAST& FLUIDMANAGEMENT srl
A Unitof Idex Corporation
1
INDEX
1. INTRODUCTION.............................................................................................................2
2. INTELLECTUALPROPERTYRIGHTS...........................................................................2
3. TECNICHALSPECIFICATIONS.....................................................................................2
4. WARRANTYTERMSANDCONDITIONS......................................................................3
5. GENERALDESCRIPTION..............................................................................................3
6. SAFETYRULES.............................................................................................................3
7. RESIDUALRISKS..........................................................................................................5
8. INSTALLATION REQUIREMENTS.................................................................................6
9. KEYBOARD....................................................................................................................7
10. HOWTOOPERATE.....................................................................................................7
11. LOADINGTHECAN INTOTHEMACHINE..................................................................8
12. ACOUSTIC WARNINGS...............................................................................................8
13. SAFETY........................................................................................................................9
14. MAINTENANCEANDCLEANING................................................................................9
15. FUNCTIONALDIAGRAM100–115 -230V...............................................................12
16. ELECTRICBOXAND WIRINGDIAGRAM230V–50Hz............................................13

FAST& FLUIDMANAGEMENT srl
A Unitof Idex Corporation
2
ENGLISH
1. INTRODUCTION
SO300 byFAST&FLUIDMANAGEMENTisthe resultofthemostrecenttechnologyin highspeedpaint
mixing.YourSO300byFAST&FLUIDMANAGEMENTisasturdyandeffectiveshaker;itswayof operating
anditsdesignshowall qualityofacarefulengineeringworkontheproduct.
Toappreciatefullyandprotectyourinvestment,wesuggestthatyoutakesometimetoread thismanual.
Asusual,FAST &FLUIDMANAGEMENTwill supportyoupostsalesassistanceservice.
Thefewmaintenanceoperations,whichwillbementionedfurtheron, shallbe carriedoutregularly.
FAST&FLUIDMANAGEMENTwillnot beheldresponsibleforanydamage or accident
whichmighthappen becauseoffailure to respecttheregulations set,orbecause of
wrong useor ofmaintenancecarriedoutwithoutthestandardsafetyrules being
followed, asexplained further on.
SO300shaker must not beswitchedon ifithasnot beenearthed throughone or boththe
earthing connection points(socket and/or earthing bolt).
2.INTELLECTUALPROPERTYRIGHTS
StatementonIntellectualPropertyRights.
Theinformationcontainedinthis manualis based ondata whichbelongto FAST&FLUIDMANAGEMENT.
Thismanualhasbeendrawnup expressly for assistance intheuse and generalmaintenance of SO300 shaker.
Thepublicationof thisinfo does not give anyallowancefor reproducingor using this manualfor other thaninstallation,use
or maintenance.
Nopart ofthis manual canbe reproduced,translated or filed (neitheroncomputer) in anyformor byanymeanswithout
writtenauthorizationbyaFAST&FLUID MANAGEMENTofficer.
3.TECNICHALSPECIFICATIONS
EN292 Part1and 2:1991 Safetyofmachinery-Fundamentals,generalprinciplesfordesign
EN418:1992Safetyofmachinery–Emergency stopequipment, functionalaspects
EN60204 Part1: 1997Safetyofmachinery–Electricalequipmentof machines-specificationsongeneralaspects.
EN954 –1:1996Safetyofmachinery–Safetyofpartsof the controlsystem–Part1: generalprinciplesfordesign
EN1088: 1995Safetyofmachinery
EN294:1992 Safetyofmachinery–Safetydistancetoavoiddamagesinareasofthe machinesthatarereachableby
upperlimbs.
EN953:1997 Safetyofmachinery-Protections–Requirementsondesignandconstruction ofmobileand/orfixed
protections.
PrEN12757-1Mixing/shaking machinesforcoating products;
EN61000-6-3Parte6-32001
EN61000-6-12001
EN61000-3-22000
EN61000-3-31995+A12001
ElectromagneticCompatibilityDirectiv(EMC)–Part3:Limits–Section 2:
Maximumnoiselevel:<70 dB
Shaking speed(motorrevolutions):=685 rpm
Machinedimensions:72cm(Width),116cm(Height),69cm(Depth),210Kg(Weight)
Maximumcan weight:35 kg
Maximumcan dimensions:HxWxD440x350x350 mm.Withinthe limits,alsosquared and ovalcanscanbe shaked.
Minimumcansheight: 65 mm
Timer:Electronic,programmable
Powersupply:0.75 kiwi230V 50Hz
0.75 kiwi115V 60Hz

FAST& FLUIDMANAGEMENT srl
A Unitof Idex Corporation
3
4. WARRANTYTERMSAND CONDITIONS
WARRANTY
FAST&FLUID MANAGEMENTTHENETHERLANDS guarantees everymachinetobe free frommaterial and
assembly defects.
Pleaserefertotermsand conditionsofsale inforce whenthe machine wasbought.
The damaged partsmust besenttoFAST&FLUID MANAGEMENTTHE NETHERLANDSwithforwarding costs
prepaid bythe user.
If thedefectiscaused byimproperor abnormaluse,therepairs willbebilledat normalcost. In thiscasean estimate
maybesubmittedbeforestarting repairs, ifrequired.
ALWAYSSTATETHESERIAL NUMBEROF THEMACHINEINANYCORRESPONDENCE CONCERNING SPARE
PARTS. The serialnumber is located ontheleft side ofthemachine body.
These agreements mustbe interpretedaccording tothe lawsof theNetherlands and forany dispute thecourtof
Sassenheimshallhave competentjurisdiction.
The manufacturer’swarrantyexpires:
•incase ofimproperuse
•incase ofuseof non-originalspare parts
•incase of repairs/adjustmentstothemachine withoutwrittenapprovaland/orbyunauthorized staff
•incase ofincomplete maintenance, orfailure toobserve the instructions containedin thismanual
Theabove conditionsareapplicableiftherearenototherconditionsexpresslyagreedon.
5. GENERALDESCRIPTION
FAST&FLUIDMANAGEMENThighspeedshakerSO300hasbeen designedtoworkin bothinpaintshops
andforsemi-industrialapplications.
FAST&FLUIDMANAGEMENThighspeedshakerSO300hasbeendesigned tofulfiltheneedsbothofthe
retailbusinesswithlimitsin productscapacity/quantityand the professionalandsemi-industrialbusinesswith
thepossibilityofhandlingbigcanswithaheight upto440 mm andweight ofup to35kg.
Themachinerequiresaverylittle maintenanceandpaint canbe produced atalowcost.
Thesystemworkswithan automaticblocking and shaking device, foratimesetbythe customer.
Forfurtherexplanation,pleasesee chapter10.
6. SAFETYRULES
WORKINGAREAS
MAINTENANCEAREA
OPERATORAREA
Compliancewithsecurityrequirements
Themachinemust beusedandserviced byqualifiedpersonnel only,sincethebad/wrongusemightcause
damagesoraccidents.
Area
Theareasofriskare:
workingarea
maintenancearea

FAST& FLUIDMANAGEMENT srl
A Unitof Idex Corporation
4
Powersupply
à230-240VOLTAGE: powersupplywith amagneto-thermalprotection device thatintervenes when current absorbed
exceeds16Ampsorforleakagecurrentof30mAmps,according to local regulations.
à115VOLTAGE:powersupply with amagneto-thermalprotectiondevice thatinterveneswhen current absorbed
exceeds25Ampsorforleakagecurrentof30mAmps,according to local regulations.
ELECTRICALWIRING CAN BEACCESSEDBY QUALIFIED PERSONNEL ONLY.
DO NO OPERATE THEMACHINE IFTHE SIDE OR REAR PANELS ARENOT ASSEMBLED.
Safeuseofthemachine
The producershall takethe allpossible careinplanning, designing, the checking the installation and the startup ofthe
machine toguaranteethemaximumoperationallevelduringa rationaluseofthe systemsupplied.
All components must beinaccordancewiththe currentsafetyregulations. Upto datesafetysystemsareinstalled in the
machine toensure the bestprotectionavailable atthemoment.
While using SO300 you must keep tothefollowing safetyrules:
The“end-user” mustkeep tothe safetyregulationsofthecountrywherethemachine isinstalled. Ifthereisa
conflict betweenEuropeanregulationandlocal regulation, themost severerule willapplyonthespecific
issue.
Installationandmaintenanceof SO300shakermust becarried out byaqualified technician.
Safetyruleswhenthemachineisoperating
1.To avoidinjuries, allpanelsofthe bodyofthe machine mustbeassembled and correctly fixed to theframe.
2.Donottamper the protective controlsystemand the doorlocking device.
3. Before any inspectionandmaintenanceoperationon SO300, disconnectitfromthe mainsoutlettoavoid
unexpected starts.
4. Do not leaveinside the SO300 tools after servicing
5. Makesure the environmentinwhichthemachineis installedcomplies withthe laws inforce (youneed tohave an
authorizationissued bythe Fire Brigade or bythecompetentauthority)andavoid adangerousmassingofpaint
cans. Itisforbidden to storeflammable materials orothermaterialsinsidethemachine.Using naked flames, white –
hot objects or any devicethat mightgenerate sparksin the room where the machine is placed.
6. Itisadvisable toinstallaventilationsystem,to guarantee that close to themachine thevapordilutionislower than
30%
7. Whenworkisfinished,do not leave the can(s) inside themachine anddonot leave themachineswitchedon.
8. Inthepremiseswhere theSO300isinstalled, within a5meterrangefromthemachine, theremust be aplatewith
the writing “Smockingis strictly forbidden”.
SO300shakermustnot beinstalledinanworkingareaclassifiedas EX
WARNING!
Avoid operatingtheSO300if itisnot loadedwithacan.
Neverusealoadwithaweight over35Kg.
Removeall cansinsidethemachinebeforeswitching itoff.
Donotplaceany damagedcan insidetheSO300. Consequent ruptureduringmixing maycausedamageto
theshaker.Running theSO300withdamaged packaging isatUser'srisk.
Alreadydamagedcansmaycausedamageto theyourmachine.
During themaintenancefollowthe securityrulesandtheproceduredescribedin thisparagraph.
TheSO300istobeoperated onlybytrained personnel. FAST&FLUIDMANAGEMENTTHE
NETHERLANDSshallnotbe liableforanydamage orinjurycausedbynon-compliancewiththe"user" and
"safety" regulationspresentedin thismanual,orbynottaking the usualandacceptedprecautionsin
handling,operatingorrepairing,evenifnot expresslystatedin thismanual.
Thisisalsovalidfordamageand/oraccidentsasaresultof changesmadetothemachine that are
implementedwithoutpriornoticetoandapprovalbyFAST&FLUIDMANAGEMENTTHENETHERLANDS.

FAST& FLUIDMANAGEMENT srl
A Unitof Idex Corporation
5
7. RESIDUALRISKS
7.1. Tableofresidual risksfortheoperator
Despiteofthemeasurestakenin the designing of themachine toguaranteeasafeuseof it, theremight happen
reasonablypredictable occurrences,whoserisk waspossibletoreduce,butnottoeliminatecompletely.
RISK DIRECT. 392 PRECAUTION
Injuriesorcrushingduring loadingand
unloading operations1.6.44.1.1 1.6.4
4.1.1 Usesecurityprotectiveglovesandshoes
duringloading and unloadingoperations
Abrasionsandinjuriescausedbysharpedgesand
partsofthecanstouse 1.6.4
4.1.1 Useprotectiveglovesduringloadingand
unloadingoperations
Liquid leakagesfromthe cans Cleancarefullythe areawherethe
operatorworks
7.2. Residualrisks fortechnicians
RISK DIRECT. 392 PRECAUTION
Dangerof electrocutionduringmaintenancecaused
byelectricchargesofmotorcapacitors115-230V 1.5.1
1.5.2 Usesecurityshoesandgloves.
7.3. Personalprotection foruser
Iftheequipmentisusedinacorrectway,the machine,asproduced in the factory,doesnotcauserisks or
dangersfortheuser, whoinanycasehavetowearindividualprotection(protectiveglasses,protective
shoes, protectivegloves)especiallyduringtheloadingand unloadingofthecans.
7.4. Generaldangersituations
Thereisnot anyparticularhazardoussituation(e.g. firerisk,loss/emissionofdangeroussubstances)butin
anycaseit isnecessarytohaveat handapowderextinguisherforpossiblefire(electricalequipments).
Securitycomponentsanddevices
Themachineisequippedwiththefollowing securitydevices:
•Anemergencypushbutton
•Adoor-locking device(solenoid)
Emergencypushbutton
Forsafetyreasons,allusersshould knowthepositionandthewaytouse theredemergency push
button.
Theemergency RED pushbutton isassembledontheoperatorpanel onthe frontpartofthemachine.
Pressing thisbutton causestheimmediatestop oftheshakingcycle andthedisconnectionofthe power
supplystoppingtheshakingmotor.Thenormal functionalitiesofthe equipmentarerestoredbyturningthe
emergency pushbuttonclockwise.Incaseofemergencystop duringtheshakingcycle,the machine
functionalitieswillbe restored aftertheresetprocedure(just pressStop/Up).
Doorlock(solenoid)and door-openmicro-switch
Thesecomponentsarepart of thesamesafetydevice(solenoid + micro-switch),whichpreventsshaking
cycle fromstartingif the doorisopen.During shakingcycle,thesolenoidkeepthedoorsafelylocked.

FAST& FLUIDMANAGEMENT srl
A Unitof Idex Corporation
6
8. INSTALLATION REQUIREMENTS
SO300hastobeplacedonalevel andstableground.Pleaseinstallthe machine byproceeding asfollows:
à230-240VOLTAGE: powersupplywithamagneto-thermal protectiondevicethatinterveneswhencurrent
absorbedexceeds16Ampsorforleakagecurrentof30 mAmps,accordingtolocalregulations.
à115VOLTAGE:powersupplywithamagneto-thermal protectiondevicethatinterveneswhencurrent
absorbedexceeds25Ampsorforleakagecurrentof30 mAmps,accordingtolocalregulations.
Environmentalconditionsmustbewithinthefollowinglimits:
Airtemperature10to40°C
Relativehumidity30to90%
Duringtheinstallationitisadvisable touseprotectiveglovestoavoid injuries.
Connectthepowercabletothe
SO300sothat you canopen
thedoor Pullthecordsfixed tothe
woodenblocks
Beforetryingtostartthe
machine,makesurethe screws
andthewoodenblockshave
beenremovedfromthe
machineitself
Undothefeetofthemachine,tillthemachine
wheelsnolongertouchtheground Block thefeet bydoingtheir respectivelocknuts
SO300shakermustnot beinstalledinanworkingareaclassifiedas EX
Removetheboltsthatfixethemachinetothepallet Removethescrewsat theinside of
thesidepanels
Set themachine levelby
usinganappropriatetool

FAST& FLUIDMANAGEMENT srl
A Unitof Idex Corporation
7
9. KEYBOARD
③⑤⑦
⑧②④⑥⑨⑩
=“LINE“Green Led= ON=Presenceofpowersupply(230V;115V;100V)
②=T1Button= Press ittostartshakingcycle T1(1minutebydefault)
③=T1Red Led = ON= T1shakingcycle activated
④=T2Button= Press ittostartshakingcycle T2(2minutesbydefault)
⑤=T2Red Led = ON= T2shakingcycle activated
⑥=T3Button= Press ittostartshakingcycle T3(3minutesbydefault)
⑦=T3Red Led = ON= T3shakingcycle activated
⑧=“CLAMPOK” GreenLed =ON= Machine isclamping thecan
⑨=ButtonStop/Up= Stopshaking/ openplate(Reset afteremergency stop)
⑩=Emergency button
10.HOWTOOPERATE
10.1.SWITCHINGSO300ON
Whenthe machineisoff, the doorislocked.
Checkthat theemergency button (10)isnotpressedin;ifitis,turnit90°clockwise.
SwitchSO300onsimplypluggingitin the mainssocket. Thegreen led “LINE”(1)willturnon.
If theupper(moving)plateisnot inthe‘completelyopen’position,itwill automaticallyunclamp.
10.2.PLACINGTHECAN
Openthedoorand placethe caninthecentreofthe lowerplate;thenclosethedoor.

FAST& FLUIDMANAGEMENT srl
A Unitof Idex Corporation
8
10.3.CANCLAMPING
The‘Canclamping’functionkeepsthecanblockedwhile themachineisshaking.
Amotorguaranteesthecontinuousclamping onthecan,whichiscontrolled byadedicated sensor.
Theclampingforceissetin thefactoryduringthe finaltest oneachshaker;in anycase,theforcecan be
modifiedbyatechnician(through theOperatorPanel)accordingtotheneeds/requirement of thecustomer.
Defaultvaluesare:
-Biggercans(upto35Kg)= 350 Kgclampingforce
-Smallercans(upto10Kg)= 250 Kgclampingforce
SO300 shakerhasanothersensor,whichrecognizesthe sizeofthecan in theinnershakingframe(bigger
orsmallercan); according tothat, thecorrect clamping pressure(1or2)isautomaticallychosenbythe
machineitself.
If,while the machine isshaking,theabove-mentionedsensorcannotdetect thecananymore,theshaking
cycle isstopped and awarningnoiseisuttered.
10.4.CANSHAKING
Theshaking cyclestartsbypressingoneofthethree buttonsT1,T2,T3, whichhave3pre-setvalueswith
differentshakingtimes(1,2or3minutes,bydefault).
Alsothese3parametershavebeenpre-setin the testing phase(in thefactory); inanycasetheycanbe
modifiedbyatechnician(through theOperatorPanel)accordingtotheneeds/requirement of thecustomer,
previousconsentofFast &Fluid Management.
Shaking:afterpressingbuttonT1(orT2orT3)the upperplatelowerstill it touchesthecan.Afterthesensor
hasascertained thatthe caniswellclamped,theshakingstarts.
At the endoftheshaking, theupperplategoesupforabout4second, andthen stops.
Shakingcan bestopped anytimebypressingbuttonStop/Up, ortheemergencybutton.
Inthismoment doorcanbeopenedandthecanmayberemoved.
Whenshaking cycleisfinished,pleaseremembernottoleavethecaninsidethemachine.
11.LOADINGTHECAN INTOTHEMACHINE
Placethe rubber
diskontothecanlid Fixthe canhandle
withthe rubberband
provided
Makesurethatthe
caniscenteredonto
thelowerplate
Itis possibleto
shakeseveralcans
withthesame
heightbyusingan
adaptor
12. ACOUSTICWARNINGS
Alloperationsaremonitored bytheresidentprogramof themachine andin caseof malfunctioningoratthe
endofthe shakingcycle,themachine givesoutawarningsound.Incaseofmalfunctioningthemachine
immediatelystops.
Herefollowsomeexamplesofmalfunctioning/warnings:

FAST& FLUIDMANAGEMENT srl
A Unitof Idex Corporation
9
Malfunctioning
-WhenbuttonsT1,T2orT3arepressedif thedoorisopen
-The clampingsensorcannomoredetect thecan whileshakingison
-Timeout. Whenthetimebetweenthestartandthe clampoksignal(keyboardposition 8)sensoristoo
long.
-Safetyviolated. Ifthedoorisforced; iftheemergencybuttonispressed.
13.SAFETY
Alloperationsaremonitoredbythe residentprogramof themachinetoguaranteetheuserworkinginsafe
conditions.Ifsafetysystemisviolated, allmachinemovements(clamping,unclamping,shaking)immediately
stop. Thefollowingtablesdisplaysignal/controlsmonitoredbythe machine.
Machinestatus FunctionSignal Functioncontrol
Off Noprecaution Nofunctional check
Clamping (withor
without can) Closed door Doorclosed
Unclamping Closed door Doorclosed
Shaking Doorclosed; clampingpressuresensor
activated Doorclosed;clamping pressuresensor activated
Standby Noprecaution Doorclosed
14. MAINTENANCEAND CLEANING
Duringmaintenanceandcheck operations, pleasewearprotectionglovesandunplugthemachine.
These operationsmustbecarriedoutbyqualifiedandtrainedtechnicians and withthemachine
unplugged (apartsafetydevice check).
14.1.Tableofperiodicservicing.
Servicing every...
Whattodo 7days 1 Month 1Years
Safetydevicescheck Cap.14.2
Bodycleaning Cap.14.3
Innerpartscleaning Cap.14.3
Threadedbarsandspringslubrication Cap.14.4
Eccentricshaft supportslubrication Cap.14.5
14.2.Check ofsafetydevices
DOORLOCK (solenoid +micro-switch)whenthemachineisoff and thedoorislocked
Ifyoupullthehandle,thedoorshall remain locked.
DOORmachineison–pluggedinto themainsbutnotworking
Whenthe machineisswitched on(plugged in)theupperplateunclampstilluppermost position.
Iftheupperplateisalreadyin theuppermost position,themachine isreadytobeloaded.
Openthedoor.
Ifyoupress T1, T2orT3,themachineshall not startbutemitawarningnoise.
Ifyoupress Stop/Up, themachine shall notstartbut emit awarningnoise.

FAST& FLUIDMANAGEMENT srl
A Unitof Idex Corporation
10
EMERGENCYBUTTON(whenthemachineisshaking)
•Switch SO300on
(just plugitin)
•Openthe door,load
a canandclosethe
door.
•Pressone ofthe start
buttons (T1,T2, T3) to
start the shaking cycle.
•Beforethe endof the
shaking cycle, press the
emergencybutton
•Shaking shall stop and a
warning noiseshallbe
heard.
•The shaking cradle shall
stopand the upperplateshall
notunclamp.
•The canshallbe trappedin
the cradle and no buttonshall
work.
•De-activateemergency
buttonbyturning it
clockwise.
•Pressallbuttons
(Stop/Upexcluded).None
of themshallwork
•Press Stop/up button.
Makesurethe upperplate
unclamps
•Check the door: it shall
beunlocked.
14.3.Cleaning
All cleaningoperationsmustbeoperated withthemachineunplugged.
Forinnerpartscleaning, beforeunpluggingthemachine,openthedoor.
Body(panels)anddoor
Useanynonabrasivecleaningproductfordomesticuseon washablesurfaces.
Control panel(keyboard)
Useawet cloth.The useofneutralsoap isallowed.Thenwipe(no rinse)withadryclothorapapertowel.
Innerpartsofthebody
Incaseofpaintloss,cleanimmediately!
Driedpaintcanberemoved withabroadknife.ThenUseanynon abrasivecleaningproduct fordomestic
useonwashable surfaces.
Innerparts(shakingcradle)
In caseof paintloss, clean immediately!
Driedpaint canberemoved witha
broad knife.
To cleanlubricatedparts, justuse a
cloth,whichwill remove the paint
togetherwiththelubricant.
Immediatelyrestorethe lubricationas
per furtherinstructions
Accidentalpaintleakages/losses insideand/oroutsidetheSO300
Immediatelycleanthemachineandthe floorofthe‘userarea’ toavoid slippingrisks.
Donot usewaterjetsorhighpressurecleanerstocleanSO300.
Donot usesolventstocleanSO300
Incasesolventsareabsolutelynecessary,afterusingthemkeep themachinedisconnectedfromthemains
anditsdoorcompletelyopenforatleast 1hour.

FAST& FLUIDMANAGEMENT srl
A Unitof Idex Corporation
11
14.4.Threadedshaftsand springslubrication
Recommendedlubricants
Useagenericadhesiveyellowgreaseforopengears,grade N.G.L.I.2.
Howtoproceed
•Greasing
•Switchthemachine on(plugit into the
mains); doorshallbe closed.
•Lower completelythe upper plate by
pressing anyofthe startbuttons(T1,
T2,T3).Before the shaking starts,
press Stop/Up.
•Openthe door.
•Unplug the machine fromthe mains.
•Removethe greaseand possible dried
paint (seeparagraph 12.3).
•Then putsome grease witha brush
onthe springs betweeninnermost
cradle and middle cradle.
•Pluginthemachine.
•Closethe door.
•Pressanyofthe start buttons (T1,
T2,T3),then Stop/Upbuttonsto
slidethe upper plate onthe
shafts.
•Repeattheoperation severaltimes.
14.5.Lubrication oftheeccentricshaft supports
Lubricatethe eccentricshaft support throughthelubrication nipples.

FAST& FLUIDMANAGEMENT srl
A Unitof Idex Corporation
12
15.FUNCTIONALDIAGRAM100 –115 -230V
Power
board
Flat
cable
ACinput
100/115/230V
50/60Hz
Operator
Panel
board
Uni-directional
ACmotordrive
Shakermotor
Digitalinputs Cansensors
DC Solenoid
drive
Doorsolenoid
Logicboard
Bi-directional
Pwmmotor
drive
Clampmotor
Digitalinputs Upperlimit switch
Keyboard
inputs keys
Digitalinputs Little/ bigCan
sensor
Keyboard
outputs Monitorleds
Digitalinputs
Digitalinputs
Emergency push
button
Doorswitch

5 5
4 4
3 3
2 2
1 1
D D C C B B A A
1813167
1813168
1813169
1813172
1813173
1813171
1813170
GND
KEYBOARD
POWERBOARD SO300
M
GND
GND
GND
25uF 80uF
STARTRUN
filter
1813166
J4 J5 J6 J7 J8
J2 J9 J3 J10 J1a
J1
1863358
Thursday, June 02, 2005
1 9
SO300
023-3-2005 NvB
1st version Changed motor wire colors, added J-numbers
SO300
NvB
2-6-2005
1.01
© 2002 Fluid Management Hub van Doorneweg 31 P.O.Box 220 2170AE SASSENHEIM
1.01
Revnr.
Sheet
Title
Date Drawn Remarks
Filename
FAST & FLUID
MANAGEMENT
Version
RED GREEN
1
3
BROWN
WHITE
BROWN BLUE BROWN BLUE 1 2 BROWN WHITE
1
BLUE BROWN
20VGREY 0 BLACK 6V YELLOW 0 BLUE
230V BROWN 0 WHITE BROWN BLUE
YEL/GRN
BLUE
RED BLACK YEL/GRN BROWN WHITE/BROWN
BLUE YEL/GRN
4
BLACK
BROWN
4
BLACK BROWN
BROWN
BLACK
GREY
3
BLACK
2
BROWN
BLACK
BLACK 2
BLACK
GREY
BROWN
GREY
1 2
M
MOTOR CLAMP SENSOR SHAKE-ENABLE
S1 SW DPNC
SENSOR CANSIZE
MICROSWITCH NO DOOR
IN
OUT1
OUT2
TRANSFORMER
MICROSWITCH CLAMPPLATE SOLENOID
DOOR
U1 NETENTRY w.fuse
5 6

FAST& FLUIDMANAGEMENT srl
A Unitof Idex Corporation
14