Fast Mover FMT9800 User manual

Product Instruction Manual
FMT9500
HVLP Gravity Feed Spray Gun
PREMIUM GRAVITY SPRAY GUN
FMT9800
Instruction Manual
T: [phone] E: [email protected] W: www.fastmovertoolsuk.com

Please keep in a safe place for future reference
1. SAFETY REGULATIONS
2. PACKAGING
3. WASTE AND ENVIRONMENT
4. INITIAL INSPECTION
5. REQUIRED INSTALLATION
6. CHARACTERISTICS
6.1 PRODUCTS THAT CAN BE SPRAYED
7. ACCESSORIES
7.1 STANDARD ACCESSORIES AND DOCUMENTATION
7.2 OPTIONAL ACCESSORIES
8. WORKING INSTRUCTIONS
9. MAINTENANCE AND CLEANING PROCEDURE
10. TROUBLESHOOTING
11. EXPLODED VIEW
12. WARRANTY
13. WARRANTY CERTIFICATE
1. SAFETY REGULATIONS
A misuse of this equipment may result in accidents, damage or malfunctioning. Read the user and
maintenance manual carefully.
Please, bear in mind the following rules:
• Ensure that the person who is going to use the gun is trained to do so.
• Disconnect the equipment for any cleaning operation or any action on it, and decompress
the circuits by pulling the gun trigger.
• Always use the equipment with approved protections (gloves, protective mask, earplugs and
proper clothing).
• The place where the device is used has to be ventilated or equipped with an air extraction
system (paint booth), and there should not be direct exposure to flames (cigarette, lamp)
while it is working.
• Keep the working area clean and without waste (rags, solvents).
• Check the chemical compatibility of the products to be used.
• Never exceed the indicated maximum pressures.
• Never use worn, folded, broken or leaking hoses.
• Do not point the gun at people or animals.
• The gun is not suitable for children.
• Do not use the gun for those operations for which it has not been designed.
• The use of halogenated hydrocarbons products may cause chemical reactions in form of
explosions, for this reason, the use of products that contain them is forbidden.
2. PACKAGING
The FMT9800 guns are presented in a cardboard box. All its standard accessories are inside the
packaging.

FMT9800 Instruction Manual
During delivery and storage, the temperature has to be between 0 and 50° (32 and 122ºF), and a non-
excessive relative humidity.
3. WASTE AND ENVIRONMENT
REMEMBER:
To get rid of polluting and dangerous products, packaging, disused equipment and tools and
any type of waste produced by its activity in general, please use the suitable waste sorting
and treatment point for each case. If you need any information related to this, please go to
the Ministry of the Environment of your regional government or the nearest city hall.
4. INITAL INSPECTION
Before using this equipment the user has to make sure that it has not been damaged during delivery or
storage. Moreover, it must be checked that all the components of the equipment are inside the packaging.
5. REQUIRED INSTALLATION
It is advisable to always use dry, oil- and dust-free compressed air for better paint results. Before
proceeding with the installation, it is necessary to carry out some inspections:
NOTES
• Check the hoses are in good condition (no cracks or folds).
• Check the air purifying filter of the supply is not full of water. Due to the fact that if it does not have
an automatic purge, its emptying is not automatic either, so it is advisable to carry out emptying
A compressor or a compressed air line connected to the gun, the pump or the pressure tank (depending
on thegun model) is required to carry out the installation.
Before connecting the gun to the compressor, close all the gun regulators (no.11 & no.14).
The air hose that goes to the air flow regulator (no. 25) comes out from the compressor.
6. CHARACTERISTICS
The FMT9800 UV range offers the best finish at the best price. It is designed to give a medium-high
finish quality. The air consumption is shown below:
FMT9800
PRESSURE CONSUMPTION
2 BAR 160 l/min.
FMT9800 Packaging
MEASURES WEIGHT
230 x136 x 136 850g
T: [phone] E: [email protected] W: www.fastmovertoolsuk.com

Please keep in a safe place for future referencePlease keep in a safe place for future reference
Fast Mover Tools tests all guns before they leave the facilities, assuring optimum operation.
Technical data FMT9800
Mim. compressor 2 CV
Available setups 1.2 ,1.3, 1.4, 1.8
Standard nozzle 1.75
Body Stamped and anodized aluminum
Pollution level Low
Max. inlet air pressure 4 bar
Max. working temperature 50º
Weight 635 gr.
Air inlet CR 1/4 M
Product supply Gravity
Technical data are indicative and can be changed without prior notice, if an improvement of
the product is considered with it.
6.1. PRODUCTS THAT CAN BE SPRAYED
The gun is designed and recommended to spray:
• UV Paints
• UV Primers
• Tintable fillers
• High solid fillers
• Lacquers
• Varnishes
7.2. OPTIONAL ACCESSORIES
Fast Mover Tools offers a wide range of optional accessories:
CONNECTION HOSE
AIR HOSE Blubird range of hoses. Length from 5mtr to 20mtr and either 8mm or 10mm.
7. ACCESSORIES
7.1. STANDARD ACCESSORIES
Fast Mover Tools delivers the gun with the following
accessories and documentation:
• UV Protective Air Cap
• Filter
• 600 CC. Nylon Tank
• Multipurpose Spanner
• User And Maintenance Manual
• Warranty Certificate
• Dyes
• Powdered glue
• Primer coat
• Forge type
• Primers
• Enamels
NYLON
TANK
FILTER

FMT4710 / FMT4720 Instruction ManualFMT9800 Instruction Manual
COMBINATION CHART
Complete set Fluid tip +
Needle MAX nozzle
FMT50215 120 INOX FMT50556 120 INOX
FMT50213 1 B
FMT50215 130 INOX FMT50556 130 INOX
FMT50215 140 INOX FMT50556 140 INOX
FMT50215 175 INOX FMT50556 175 INOX
8. WORKING INSTRUCTIONS
1. Close the gun regulators (no.11 & no.14).
2. Prepare the product to be sprayed (according to the manufacturer’s instructions).
3. Loose the product regulator (no.11), point the gun at a paint pit or a test surface and pull the
trigger until the paint comes out.
4. Adjust the air inlet pressure from the regulator (no.25) until you get the desired flow.
5. Adjust the fan width (no.14) and the product regulator (no.11) until you achieve the desired
paint pattern.
NOTES:
• Always use the gun in a perpendicular position to the area to be painted.
• Avoid working only with a wrist movement.
• Do not forget that cross coats do not cover evenly.
• Spraying with an immobile gun causes a local overload. Therefore, do not pull the trigger before
starting to move your arm, and do not release it before finishing the movement.
• Try to get a spraying with regular and constant thickness between the different coats.
9. MAINTENANCE
The ordinary maintenance of the gun is very simple as it does not require any special operation. To
ensure the proper functioning, you only have to clean the paint circuit after finishing the activity.
A recommendation for the product to last longer is to use well filtered paints and avoid paints
which block the nozzle easily.
CLEANING PROCEDURE:
1. Replace the paint with solvent.
2. Adjust the air to the minimum working pressure (around 1 bar).
3. Pull the trigger until the whole circuit is completely clean.
4. Clean the air nozzle with a cloth and a brush.
5. Clean the gun body with a cloth.
6. Lubricate all the moving parts.
T: [phone] E: [email protected] W: www.fastmovertoolsuk.com

Please keep in a safe place for future reference
CLEANING NOTES:
• If the cleaning is done in an industrial washing machine for spray guns, the air and product
regulators have to be closed (so that the solvent does not damage the joints). Dry the gun with
a blowing gun once the cleaning cycle has finished.
• Do not use metallic brushes for cleaning.
• Never sink the gun into solvent.
10. TROUBLESHOOTING
A table with incidents that the user can solve himself is shown below.

T: [phone] E: [email protected] W: www.fastmovertoolsuk.com
FMT9800 Instruction Manual
Technical data FMT9800
No. Reference Description
1 FMT9800/50566B Nozzle nut
2 FMT9800/50267B1 Joint, 1 unit
3 FMT9800/50213XB Nozzle (See Combination Chart - Page 5)
4+7 FMT9800/50556XXXINOX Fluid tip + needle (See Combination Chart - Page 5)
5 FMT9800/505981B Joint, 1 unit
6+24 FMT9800/501071 Tank + filter
8 FMT9800/500111B Joint, 1 unit
9 FMT9800/50206B Bushing
10 FMT9800/502141B Spring, 1 unit
11 FMT9800/500141B Product regulator, 1 unit
12 FMT9800/50016 Valve closing
13 FMT9800/50069B Valve kit
14 FMT9800/50595B Fan regulator
15 FMT9800/50596B O-ring, 10 units
16 FMT9800/50059B Fan regulator nut
17 FMT9800/500061B Seeger ring, 2 units
18 FMT9800/50597 Fan regulator set
19 FMT9800/501371B Packing, 1 unit
20 FMT9800/501381B Packing nut, 1 unit
22 FMT9800/50586B Stud bolt, 1 unit
23 FMT9800/50038B Trigger
25 FMT9800/50022B Air inlet regulator
26 FMT9800/50070 Complete valve
27 FMT9800/10CR1/4HBLISTER Air inlet connector
FMT9800/SK001 Service pack for FMT9800, Valve Packings (12) and Seal Kit (19)
11. EXPLODED DIAGRAM

Fast Mover Tools Limited
1 French’s Ave, Dunstable LU6 1BH
T: [phone] E: [email protected] W: www.fastmovertoolsuk.com
Please look after the environment, dispose of all packaging in a responsible
way. Always dispose of tools in accordance with local authority guidelines.
© 2022 Fast Mover Tools Ltd. This document is copyright and is not to be
copied, circulated, distributed or shown to anyone other than the intended
recipient without the express permission of the directors.
12. WARRANTY
This equipment is covered with a 2-year warranty from the date of purchase. The guarantee
covers against manufacturing faults and components defects. Only repairs and elements
substitution carried out by technical staff of Fast Mover Tools are covered. Faulty pieces will
be sent carriage paid.
Warranty does not cover:
• Faults or damages caused by improper use of the equipment.
• Faults or damages caused by the use of spare parts different from the original ones or
those recommended byFast Mover Tools.
• Faults or damages caused by bad maintenance.
• Components subject to wear (nozzles, filters, etc.).
Warranty is void:
• Whenever repairing operations or components substitutions are carried out without prior
authorization of Fast Mover Tools.
• Whenever the serial number is removed or manipulated.
• Whenever it is checked that the fault has been caused by improper use or if the
equipment falls, is bumped or by other causes not due to normal working conditions.
All repairing interventions carried out under warranty will not entail a stoppage or extension of
the warranty period.
13. WARRANTY CERTIFICATE
FMT9800 Instruction Manual
Cut along the dotted line
Purchaser: .........................................................
Address: ............................................................
City: ...................................................................
Model: FMT9800 Date of purchase:
Serial number:
Distributor Stamp: