febromed get up User manual

get up®
The Swiveling Hold System for Radiology
Instruction Manual
F-049 GB Rev00 02.05.2019

2F-049 GB Rev00 02.05.2019 get up® Instruction Manual
Instruction Manual: get up® hold system
Item number: getup2018
1 Legal Information
Manufacturer:
febromed GmbH & Co. KG
Am Landhagen 52
D-59302 Oelde
Contact:
Phone: [phone]
Fax: [phone]
Internet: www.febromed.de
E-Mail: [e-mail]
Registry Court:
Amtsgericht Münster
HRB no.: 10077 Febromed-Beteiligungs-GmbH
HRA no.: 7608 Febromed GmbH & Co.KG
Ident.-No.:
DE 814491165
Directors:
Dr. Reinhold Festge
Hubert Brormann
Protection Note:
The passing on as well as the duplication of this document, the utilization and the disclosure of its contents
are prohibited, and also expressively not permitted.
Infringement leads to compensation.
In case of a patent, utility model or design model registration, all rights are reserved.
Nominal Charge:
24,00 €

get up® Instruction Manual F-049 GB Rev00 02.05.2019 3
2 Table of Contents
1Legal Information........................................................................................................2
2Table of Contents........................................................................................................3
3Preface.........................................................................................................................5
4About the Instruction Manual.....................................................................................5
4.1 Purpose of the Instruction Manual..................................................................................... 5
4.2 Users of the Hold System ................................................................................................. 5
4.3 Using the Instruction Manual............................................................................................. 5
5Usage...........................................................................................................................6
5.1 Intended Use.................................................................................................................... 6
5.2 Misuse.............................................................................................................................. 6
6Warranty ......................................................................................................................7
7Technical Data.............................................................................................................7
8Componenten..............................................................................................................8
9Function.....................................................................................................................10
9.1 Swiveling the get up®......................................................................................................10
9.2 Altering the Position of the Triangle Handle .....................................................................10
9.3 Adjusting the Handle Height.............................................................................................11
9.3.1 Lowering the Handle .........................................................................................11
9.3.2 Raising the Handle............................................................................................12
10 Preparation................................................................................................................12
11 Maintenance ..............................................................................................................14
12 Spare Parts................................................................................................................14
13 Disposal.....................................................................................................................15
14 Customer Service......................................................................................................15
15 Customer Satisfaction..............................................................................................15
16 List of Figures ...........................................................................................................15
17 Appendix....................................................................................................................16

4F-049 GB Rev00 02.05.2019 get up® Instruction Manual
17.1 Appendix A: Instruction: get up® Hold System.............................................................16
17.2 Appendix B: EC Declaration of Conformity...................................................................17
17.3 Appendix C: Suitable Cleaning Agents and Surface Disinfectants ...............................18
17.4 Appendix D: Maintenance History File: get up® Hold System - Annual Maintenance
Activities.................................................................................................................................19
17.5 Appendix E: Product Options/Extensions.....................................................................20
18 Notes ..........................................................................................................................21

get up® Instruction Manual F-049 GB Rev00 02.05.2019 5
3 Preface
We developed the get up® in close collabora-
tion with medical staff while focusing on the
needs and processes in healthcare. The
result was an individually adjustable swiveling
system, which is functioning as a stand-up,
hold and lay-down aid for daily routines in
hospitals.
To guarantee durability and low maintenance
requirements, we put great emphasis on a
purely mechanical construction without the
need for electronics or cabling.
To meet all individual requirements, the get
up® is provided with a swivel arm of adjusta-
ble length, a number of eyelets and the
possibility of using various supplementary
components.
4 About the Instruction Manual
Handling the Instruction Manual
Read the instruction manual completely
before using the get up® for the first time.
Always store the instruction manual close to
the get up®.
When entrusting the get up® to a third
party, always include the instruction manual.
4.1 Purpose of the Instruction Manual
The instruction manual describes the proper
use of the get up® hold system.
The application of the instruction manual is
intended to prevent damage to the get up®
as well as the equipment and to protect the
health and life of personnel and patients.
If used as described in the instruction manu-
al, the service life of the hold system will also
be extended.
4.2 Users of the Hold System
The get up® hold system may only be
operated under the supervision of personnel
who have been instructed in the use of the
get up®.
Regular maintenance and inspection must be
carried out by qualified staff before each use.
Annual maintenance must be carried out by
qualified staff who are familiar with the
maintenance of medical devices. These staff
are henceforth referred to as maintenance
personnel.
The evidence of instruction, which required in
this respect, is to be documented in Appendix
A of the instruction manual.
4.3 Using the Instruction Manual
It is important to study the manual in its
entirety. Do not leave out any chapters.
The get up® must not be used until the
instruction manual has been fully understood.
If you have any questions, please contact our
hotline:
febromed hotline
+ 49 (0) 2522 / 30 -532
All chapters of this instruction are listed in the
table of contents on pages 3 and 4. The

6F-049 GB Rev00 02.05.2019 get up® Instruction Manual
illustrations shown in this instruction manual
are intended to clarify the instructions de-
scribed in the texts. In the following table,
labels for instructions are listed to illustrate
the degree of hazards. The labels are for
orientation only. The classification of the
hazard potential is only exemplary, a higher
potential must be taken into account.
febromed assumes no liability for the classifi-
cation.
Signal Word and Meaning
Information Important to Know
ATTENTION
Action can cause property damage or
environmental damage
CAUTION
Action can cause minor injury
WARNING
Action can cause considerable property
damage or considerable injury
DANGER
Action can cause serious injury or death
5 Usage
5.1 Intended Use
The chapter describes the use intended by
the manufacturer.
The get up® is a 360° swiveling hold system,
which was designed as a support which
patients in the radiology department can hold
on to when standing up and laying down.
CAUTION
Danger to Health Due to Damaged or Soiled
Surfaces
A damaged surface of the handle may cause
injury to patients and medical staff. A soiled
surface increases the risk of patients and
qualified staff falling ill.
Check the handle of the get up® for cracks
and other damage before each use.
Replace a torn or damaged handle before
use.
Check the get up® for pollution before each
use.
Remove any dirt before use.
ATTENTION
Property Damage Due to Overloading
Exceeding the maximum weight limit can cause
damage to the material of the get up®.
The get up® can be loaded with a maximum
load of 135 kilograms.
5.2 Misuse
The chapter describes the use defined as
misuse by the manufacturer.
ATTENTION
Property Damage Due to Suspended
Objects
Die Verwendung des get up® als Kran oder
Aufhängemöglichkeit von Gegenständen kann

get up® Instruction Manual F-049 GB Rev00 02.05.2019 7
zu Schäden am get up® führen.
Do not hang any objects on the get up®.
Do not move any loads with the get up®
- misuse as a crane.
WARNING
Risk of Injury Due to Overloading
Employing the get up® as a swinging rope can
lead to injuries for patients and medical staff.
Do not employ the get up® as a swinging
rope.
List only exemplary
6 Warranty
The legal warranty on the get up® amounts
to two years starting from the date of deliv-
ery.
This warranty does not include wear parts.
The warranty expires if you:
damage the get up® willfully.
misuse the get up®.
disregard the intended use as per instruc-
tion manual.
have a repair carried out by a non-expert.
7 Technical Data
The following chart lists all technical data of
the get up® (technical values may vary
depending on design):
Components
Technical Data
Type Designation
get up®
Item Number
get up2018
Height
max. 1.950mm, see
order drawing
Width
550mm
Depth
max. 2.450mm, see
order drawing
Weight
Up to 115kg
Maximum Weight
135kg
Ambient Temperature
+5°C up to +40°C

8F-049 GB Rev00 02.05.2019 get up® Instruction Manual
8 Componenten
The chapter concisely displays the get up® with all its components.
Komponenten des get up®
Abb.1: Components of the get up®
1
3
4
5
6
7
9
24
13
20
19
15
14
10
23
21
22
2
8
11
12
16
17
18

get up® Instruction Manual F-049 GB Rev00 02.05.2019 9
Position
Volume
Spare Part Number
Part Name
1
6
ZK0000_075
Hexagon screw
2
6
ZK0000_038
3D washer
3
1
VARIO-7950_012
Lid
4
1
VARIO-7950_011
Thrust ring
5
1
VARIO-7950_013
Ceiling cone
6
1
VARIO-7950_010
Bearing flange
7
2
ZK0000_072
Socket
8
2
VARIO-7950_029
Ring
9
1
VARIOD-7950_067
VTZ profile
10
1
VARIO-7950_018
Decor plate
11
8
KZ0000_139
Washer 10
12
8
ZK0000665
Cylinder with half head M10x45
13
1
ZK0000_007
Locking bolt
14
1
VARIOD-7950_057
Cap nut with bore
15
1
ZK0000_073
Hexagon nut M20x1,5
16
4
ZK_0000_434
Threaded rod M12
17
12
ZK0000_263
Washer
18
12
ZK0000261
Nut
19
2
VARIOD-7950-064
Fishing-line guide
20
1
VARIOD-7950-051
Towing rope incl. Ball and screw
connection
21
1
F-049 GB
Instruction Manual
22
1
VARIO-7950_001
Swivel tube
23
1
getup 002
Handle suspension
24
1
getup 010
Triangle handle Automatic

10 F-049 GB Rev00 02.05.2019 get up® Instruction Manual
9 Function
9.1 Swiveling the get up®
WARNING
Property Damage Due to Collision
Objects which are located within the pivot
radius of the get up® can be permanently
damaged by collisions.
Make sure that there are no objects located
within the pivot radius of the get up®.
Collisions with fixed objects, furniture and
walls can be prevented by installing a
turning radius limitation.
1. Grab the triangle handle with one hand.
2. Tighten the strap by pulling the triangle
handle slightly downwards.
3. With the other hand, pull the rope downwards
and keep it pulled.
The lock is now released and the get up®
can be swiveled.
4. Swivel the get up® to the desired position.
5. Loosen the pull rope.
6. Swivel the get up® a few degrees further in
any direction.
The lock audibly engages, the get up® can
now be used.
7. Make sure that the lock has engaged by
trying to swivel the get up®.
Abb.2: Swiveling the get up®
9.2 Altering the Position of the Triangle
Handle
To achieve an optimum positioning of the
triangle handle, the get up® has one or two
mounting rails with several mount points,
depending on the model.
1. Grab the handle with your hand.
2. Heben Sie die Haltegriffaufhängung an, bis
sie den Schwenkarm des get up® berührt.
3. Move the handle mounting to the desired
position.
4. Lower the handle mounting until it snaps into
a mount point.
The triangle handle is now located in the
desired location and the get up® can be
used.
5. Make sure that the grab handle suspension is
engaged in the suspension point.
1
2
3
4
5
6

get up® Instruction Manual F-049 GB Rev00 02.05.2019 11
Abb.3: Altering the Position of the Triangle Handle
9.3 Adjusting the Handle Height
The get up® has a triangle handle swiveling
360° with a continuously adjustable strap. To
ensure a secure grip, you can optimally
adjust the handle height to the patient’s
height.
9.3.1 Lowering the Handle
1. Grab the triangle handle with one hand.
2. Lightly pull down the triangle handle to
tighten the strap.
3. Push and hold the button on the belt buckle
with the other hand.
The belt buckle is now unfastened.
4. Pull down the triangle handle until the desired
strap length is reached.
5. Release the button on the belt buckle.
The belt buckle snaps audibly.
6. Make sure that the belt buckle is engaged by
means of a tension test.
Abb.4: Lowering the Triangle Handle
1
2
3
4
1
2
3
4
5

12 F-049 GB Rev00 02.05.2019 get up® Instruction Manual
9.3.2 Raising the Handle
1. Grab the handle with one hand.
2. Lightly pull down the triangle handle to
tighten the strap.
3. Push and hold the belt buckle with the other
hand.
The belt buckle is now unfastened.
4. Reduce the fraction on the triangle handle
until the handle is lifted to the desired
position.
5. Release the button on the belt buckle.
The belt buckle snaps audibly.
6. Make sure that the handle has been raised
as desired.
Abb.5: Raising the Triangle Handle
10 Preparation
The get up® must be disinfected for cleaning.
The following warnings must be observed:
ATTENTION
Loss of Efficacy Due to Inappropriate Aids
Poorly absorbent aids lead to insufficient
disinfection.
Only use absorbent material,
e.g. fleece.
ATTENTION
Environmental Damage Due to Disinfectants
If surface disinfectants find their way into soils
and waters, the environment can be put at risk.
Always dispose of surface disinfectants
without polluting surface waters or the
sewer system.
Follow the disposal instructions of the
disinfectant manufacturer.
WARNING
Chemical Burn on Hair or Skin
If surface disinfectant finds its way to unpro-
tected hair or skin, chemical burns can occur.
Always wear protective gloves when in
contact with surface disinfectant; Protective
gloves made of nitrile or butyl rubber are
particularly suitable.
If brought into contact with hair or skin:
Immediately wash the surface disinfectant
off the skin and hair using tap water of
drinking quality.
WARNING
Serious Eye Damage
1
2
3
4
5

get up® Instruction Manual F-049 GB Rev00 02.05.2019 13
If surface disinfectant finds its way to unpro-
tected eyes, serious damage can occur.
Always wear protective glasses with side
protection when in contact with surface
disinfectant.
If brought into contact with eyes:
Immediately rinse the eyes carefully for
several minutes using tap water of drinking
quality.
Remove your contact lenses beforehand if
possible.
Follow the safety instructions of the
disinfectant manufacturer.
WARNING
Danger of Slipping Due to Wet Floors
Floors soaked in surface disinfectant are
slippery and can cause people to fall.
Immediately remove spilt surface
disinfectant with an absorbent material such
as a cloth or fleece.
WARNING
Property Damage Due to Unsuitable Surface
Disinfectants
Unsuitable surface disinfectants can perma-
nently damage the surface of the get up®.
Use the surface disinfectants approved by
the manufacturer.
A list of suitable and approved
disinfectants can be found in chapter
17.3 –page 17.
Only use surface disinfectants of an
alcoholic strength by volume of
less than 25 g ethanol (94 %) per 100 g
disinfectant.
Only use surface disinfectants of an
alcoholic strength by volume of
less than 35 g propan-1-olper 100 g
disinfectant.
Only use surface disinfectants:
- without iodine.
- without ammonia.
- without hydrochoric, phosphoric and
acetic acid.
Only use surface disinfectants which
neither scratch nor scrub.
DANGER
Danger of Fire and Explosion
If surface disinfectants are brought into contact
with ignition sources such as open flames, fire
and explosions can occur.
Comply with the fire and explosion safety
regulations when employing alcoholic
surface disinfectants.
Always use surface disinfectants out of the
reach of ignition sources.
In case of fire:
Only control the burning area with
extinguishing powder, foam, water spray or
carbon dioxide (CO2) as suitable
extinguishing agents.
Observe the instructions of the disinfectant
manufacturer.
1. Disinfect the get up® after each use.
2. Dilute the surface disinfectant with lukewarm
water according to the manufacturer
specifications.
3. Dampen the fleece with the mixture of
surface disinfectant and tap water of drinking
quality.
4. Moisten the get up® with the fleece.
5. Allow the surface disinfectant to take effect
according to the manufacturer specifications.
6. Wipe the get up® with a fleece soaked in tap
water of drinking quality.
The get up® is now disinfected.

14 F-049 GB Rev00 02.05.2019 get up® Instruction Manual
11 Maintenance
Regular maintenance, which must be per-
formed before each use of the get up®, as
well as annual maintenance are carried out
by instructed personnel (see chapter 4.2,
page 5).
The following chart lists all necessary
maintenance services for the get up®:
Maintenance
Work
Description
Regular Visual
Inspection
Inspecting the towing
rope of the get up® for
cracks and other dam-
ages
Inspecting the get up®
for pollution
Inspecting the rubber
buffers of the turning
radius limitation for
abrasion
Regular
Functional Test
Inspecting the rewind
mechanism of the
strap for proper
function
Inspecting the function
of the unicycle
mechanism of the
swivel arm
The annual maintenance and repairs have to
be documented in the maintenance history
file Appendix D.
Repairs
Repairs may only be carried out by febromed or
a specialist, otherwise the warranty expires:
Febromed hotline:
+ 49 (0) 2522 / 30 -532
12 Spare Parts
If you need spare parts for your get up®,
please contact our customer service (chapter
14, p. 15).
ATTENTION
Property Damage Due to Improper
Installation of Spare Parts
The use of unsuitable spare parts as well as the
improper installation of spare parts can cause
damage to the get up®.
Only use original spare parts.
Have the spare parts installed by a special-
ist only.
Carry out a functional test after assembly.

get up® Instruction Manual F-049 GB Rev00 02.05.2019 15
13 Disposal
Before disposing of the get up®, you have to
take note of the following warning:
ATTENTION
Violation of Local Regulations
Violating the local regulations when disposing
of the get up® may result in legal consequenc-
es.
Dispose of the get up® according to the
local regulations
Dispose of all packaging materials in
accordance with local regulations.
For a disposal fee, you can send the get up®
to febromed and febromed will dispose of it in
accordance with the applicable disposal
regulations.
14 Customer Service
The customer service can be reached in the
following ways:
Customer Service
febromed GmbH & Co. KG
Am Landhagen 52
D-59302 Oelde
Phone: [phone]
Fax: [phone]
Internet: www.febromed.de
E- mail: [email protected]
15 Customer Satisfaction
The product development of febromed has
the motto:
„If there is a way to do something better, it is
our way!“
We continuously develop our products for the
benefit of people and the environment. At
every stage of development, we attach
particular importance to improving the bene-
fits for the customer.
The ideas and assessments of our customers
help us to constantly improve our products.
In order to share your experience and opinion
with us, please contact our hotline or send us
an e-mail.
16 List of Figures
Abb.1: Components of the get up®...............8
Abb.2: Swiveling the get up®......................10
Abb.3: Altering the Position of the Triangle
Handle........................................................11
Abb.4: Lowering the Triangle Handle..........11
Abb.5: Raising the Triangle Handle............12

16 F-049 GB Rev00 02.05.2019 get up® Instruction Manual
17 Appendix
17.1 Appendix A: Instruction: get up® Hold System
Instructee
Signature
Name
Department of the Company
Instructor
Signature
Name
Department of the Company
Location
Date of the Instruction

get up® Instruction Manual F-049 GB Rev00 02.05.2019 17
17.2 Appendix B: EC Declaration of Conformity
In accordance with the EC Regulation (EU) Nr.: 305/2011
We,
febromed GmbH & Co. KG
Zum Mühlenteich 1
D-59302 Oelde
hereby declare, under our sole responsibility, that our products comply with the standards due to
their design and construction as well as the design we have placed on the market.
In the event of a change to the product not agreed with us, this declaration loses its validity.
Product Description
Stand-up, hold and lay-down aid for radiology
Type of Product
get up® swiveling hold system
Relevant EC-Regulation
Regulation (EU) Nr. 305/2011 (dated 09. März 2011)
Date: 01.04.2019
Manufacturer’s signature: _______________________________________________
Hubert Brormann / Director

18 F-049 GB Rev00 02.05.2019 get up® Instruction Manual
17.3 Appendix C: Suitable Cleaning Agents and Surface Disinfectants
The following table lists all cleaning agents and surface disinfectants suitable for get up® and
approved by the manufacturer:
Product Name
Manufacturer
mikrozid® AF wipes
Schülke & Mayr GmbH
pursept® AF
terralin® protect
cleanisept® wipes forte maxi
Dr. Schuhmacher
Dismozon® pur wipes
BODE Chemie GmbH
Mikrobac® Virucidal Tissues

get up® Instruction Manual F-049 GB Rev00 02.05.2019 19
17.4 Appendix D: Maintenance History File: get up® Hold System - Annual Maintenance
Activities
Location:
Signature
Form no. F-P-33 Further forms can be ordered from febromed.
Department:
Repairs
Check unicycle mecha- nism
i. O. n. i. O.
i. O. n. i. O.
i. O. n. i. O.
i. O. n. i. O.
i. O. n. i. O.
i. O. n. i. O.
i. O. n. i. O.
i. O. n. i. O.
Check rewind mecha- nism
i. O. n. i. O.
i. O. n. i. O.
i. O. n. i. O.
i. O. n. i. O.
i. O. n. i. O.
i. O. n. i. O.
i. O. n. i. O.
i. O. n. i. O.
Check rubber buffer
i. O. n. i. O.
i. O. n. i. O.
i. O. n. i. O.
i. O. n. i. O.
i. O. n. i. O.
i. O. n. i. O.
i. O. n. i. O.
i. O. n. i. O.
Location:
Check for pollution
i. O. n. i. O.
i. O. n. i. O.
i. O. n. i. O.
i. O. n. i. O.
i. O. n. i. O.
i. O. n. i. O.
i. O. n. i. O.
i. O. n. i. O.
Check for cracks and damage
i. O. n. i. O.
i. O. n. i. O.
i. O. n. i. O.
i. O. n. i. O.
i. O. n. i. O.
i. O. n. i. O.
i. O. n. i. O.
i. O. n. i. O.
Serial no.:
Date

20 F-049 GB Rev00 02.05.2019 get up® Instruction Manual
17.5 Appendix E: Product Options/Extensions
Item Number
Product Description
get up-UK
Substructure for Swiveling Hold System get up®
• Installation of the suspended ceiling
• Minimum height of the suspended ceiling: 320mm
• Maximum height of the suspended ceiling : 1.500mm
• static elements primed
get up 002
Handle Suspension
• Holder for handle 360° rotatable, can be attached variably to
the holder on the get up®
• Handle with straightening belt, Automatic
• For optimal adjustment of the handle height to the physical
characteristics of the user
• Recommended mounting height at the get up® approx.
2.250 mm
Vario-SB
Turning Radius Limitation
• to limit the swivel angle,
prevents the striking of the Swivel arm on furniture, walls,
appliances
Get up 008
Additional Mounting Rail
• made of stainless steel
• 8 additional suspension points, 100mm locking distance
Get up 010
Replacement Handle
• Handle with erecting belt, Automatic
• triangular
•height-adjustable
•for mounting in the holder of the grab handle suspension