Feit Electric SL50-36/RGB/AG User manual

a. Ground Fault Circuit Interrupter (GFCI) protection is to be provided on the circuit(s) or outlet(s) to be
used for the wet location portable luminaire. Receptacles are available having built-in GFCI
protection and are able to be used for this measure of safety.
b. Do not mount or place near gas or electric heaters, replace, candles, or other similar sources of heat.
c. Do not secure the wiring of the product with staples, nails, or place on sharp hooks.
d. Install only using the mounting means provided.
e. Do not let lights rest on the supply cord or on any wire.
f. Do not use this product for other than its intended use.
g. Do not hang ornaments or other objects from the cord, wire, or lights.
h. Do not close doors or windows on the product or extension cords as this may damage the
wire insulation.
i. When in use, do not cover the product with cloth, paper, or any material that is not part of
the product.
j. Keep lights away from any combustible surface.
k. Read and follow all instructions that are on the product or provided with the product.
l. This product should be installed out of the reach of children.
m. Do not secure string lights to buildings or other structural supports using nails, staples or other sharp,
conducting materials. DO NOT DAMAGE THE WIRE.
n. Do not submerse.
o. Use only three-wire outdoor extension cords that have three-prong grounding plugs and grounding
receptacles that accept the appliance's plug.
p. Use only with an extension cord for outdoor use, such as an extension cord of cord type SEW, SEOW,
SEOOW, SOW, SOOW, STW, STOW, STOOW, SJEW, SJEOW, SJEOOW, SJW, SJOW, SJOOW, SJTW, SJTOW,
or SJTOOW.
DRAWINGS NOT TO SCALE.
MODEL SL50-36/RGB/AG
SMART PERMANENT LED STRING LIGHTS
Only supports
2.4GHz Wi-Fi
networks
Feit Electric app
Works with
1.Replug in the power supply and press the power button to confirm it is turned on.
2.Ensure all connections are properly secured.
CONNECTING MULTIPLE SETS
SAVE THESE INSTRUCTIONS
CAUTION:
1. To avoid risk of shock, always make sure the product is unplugged from the electrical outlet before
assembling, disassembling, installing, relocating, servicing or cleaning it.
2. Do not overload. This product contains 50FT of string lights, made of three 16.6-foot sections. Each
section uses up to 9W. One additional extension of 16.6FT (sold separately) can be added to reach a total
of 66.6 feet and use up to 36W.
3. Do not use with extension cord near water or where water may accumulate. Keep at least 4.8 m / 16 ft
from pools and spas. Keep plugs and receptacles dry. Do not submerse.
4. Do not exceed the lowest of the indicated maximum wattage on the cord tag near the connected
product’s receptacle.
5. TO REDUCE THE RISK OF FIRE: Do not replace the attachment plug. It contains a safety device (fuse) that
should not be removed. Discard product if the attachment plug is damaged.
INSTALLING PERMANENT STRING LIGHTS
Connect to
Power Outlet
mounting
screws
NOTE: WHEN NOT IN USE,
ENSURE THE FEMALE END CAP
IS COMPLETELY SCREWED IN.
String Light
16.6ft / 5m
LED Controller
3.28ft /1m
Power Supply
4.6ft / 1.4m
Extra Cord
8.2ft / 2.5m
Additional String Light
16.6ft / 5m
cap
female
Use with the mounting tape or mounting screws
16.6in / 42cm
WARNING: When using outdoor use portable luminaires, basic safety precautions should always be followed to
reduce the risk of re, electric shock, and personal injury, including the following:
READ ALL INSTRUCTIONS
TROUBLESHOOTING TIPS - MOUNTING
The mounting tape is
on the back of the LEDs.
NOTE: DO NOT OVERTIGHTEN THE SCREW.
NOTE: IT IS RECOMMENDED TO
MOUNT USING BOTH MOUNTING
TAPE AND MOUNTING SCREWS.
NOTE: THESE PERMANENT STRING LIGHTS
INCLUDE PERMANENT MOUNTING TAPE
AND MAY CAUSE SURFACE DAMAGE IF
REMOVED. NOT RECOMMENDED FOR
MOUNTING ON BRICK OR CONCRETE. FEIT
ELECTRIC IS NOT RESPONSIBLE FOR
DAMAGE TO MOUNTED SURFACES.
Includes an extra 8.2ft/2.5m female/male
connector cord for increasing cable length
Product Specifications:
• 120VAC 36W 50/60Hz
• Dimmable with app
• Suitable for Wet Locations
• IP65 Water Resistant
36 WATTS 50 FT 9W/16.6FT3 DO NOT EXCEED
4 SECTIONS / 66.6FT
(EXTENSION
SOLD SEPARATELY)
MAXIMUM
WAT TAGE STRING LIGHT LENGTH IN BOX 1 LIGHT SECTIONNUMBER OF LIGHT SECTIONS IN BOX MAX LENGHT
1 of 4 FEIT ELECTRIC COMPANY | PICO RIVERA, CA | [phone] | FAX [phone] | www.feit.com 4 of 4 FEIT ELECTRIC COMPANY | PICO RIVERA, CA | [phone] | FAX [phone] | www.feit.com

Power Supply and LED Controller
LIMITED WARRANTY
This product is warrantied to be free from defects in workmanship and materials for up to 1 year from date of purchase. If the product fails within the warranty period, please visit
feit.com/help for help. REPLACEMENT OR REFUND IS YOUR SOLE REMEDY. EXCEPT TO THE EXTENT PROHIBITED BY APPLICABLE LAW, ANY IMPLIED WARRANTIES ARE LIMITED IN
DURATION TO THE DURATION OF THIS WARRANTY. LIABILITY FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES IS HEREBY EXPRESSLY EXCLUDED. Some states and provinces do not allow
the exclusion of incidental or consequential damages, so the above limitation or exclusion may not apply to you. This warranty gives you specific legal rights, and you may also have other
rights which vary from state to state or province to province.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to
radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the
separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for
help. Any changes or modifications not expressly approved by the manufacturer could void the user's authority to operate the equipment.
Supplier’s Declaration of Conformity:
47 CFR § 2.1077 Compliance Information
Responsible Party:
Feit Electric Company, 4901 Gregg Road,
Pico Rivera, CA 90660, USA 562-463-2852
Unique Identifier: SL50-36/RGB/AG
Download the Feit Electric app on your
smart device
Plug in your Smart Permanent String Lights
Feit Electric app
Launch and use the Feit Electric app to
complete the setup
Getting Started:
Tap Add Device or the +sign, then select Chasing Lights
and confirm. You will be prompted to enter your Wi-Fi
network and password.
Pair your device
Press and hold for 5 seconds when lights are On to enter
pairing mode. Lights will blink.
Be sure to connect to a
2.4 GHz Wi-Fi network
that covers your
installation location.
Plug the Smart Permanent String Lights into an outdoor
rated GFCI receptacle.
WARNING: These products may represent a possible
shock or fire hazard if improperly installed or attached in
any way. Products should be installed in accordance
with the owners manual, current electrical codes and/or
the current National Electric Code (NEC).
See "Installing Permanent String Lights" section on
page 4.
Install your Smart Permanent String Lights
(Optional) Connect to Google Assistant or Alexa using
the in App guide
Choose Alexa or GoogleTap Pen icon
Thank you for your purchase
Questions, comments or feedback?
We’d love to hear from you.
Visit feit.com/help for support or connect with us:
Need Help?
To activate smart features proceed to steps 4 & 5.
The performance specifications (life hours) printed on this manual should only be considered an approximation of expected performance.
TROUBLESHOOTING TIPS - WI-FI
If you are having difficulty connecting:
• Make sure the Wi-Fi network is a 2.4 GHz network. Smart Permanent String Lights will not connect to a 5 GHz network.
• Test your Wi-Fi network with other devices such as your phone to make sure it is operating properly.
• The Wi-Fi connection may not have good coverage during set up. Try moving the Smart Permanent String Lights closer to your Wi-Fi router.
• Your Wi-Fi network password is case sensitive, make sure you are entering correctly. Devices plugged into your Smart Wi-Fi Plug must be ON in order to
be controlled via the mobile app.
Please also check the App User Guide for more information.
feit.com/help
@FeitElectricInc@FeitElectric feitelectriclighting
8 MODES:
1. Party
2. Red
3. Green
4. Blue
5. White
6. Fade
7. Chasing
8. Flow
Radiation Exposure Statement
This device complies with FCC radiation exposure limits set forth for an uncontrolled environment. This device should be installed and operated with a minimum distance of 20cm between the radiator and your body.
Color
Chasing Lights
Press power button once to turn on and twice to turn o.
Press and release to cycle through 8 dierent colors, themes or modes.
Press and hold for 5 seconds or until bulbs start to blink to enter pairing mode or to reset.
NOTE: WHEN USING OUTDOORS,
PLUG THE UNIT INTO AN
APPROPRIATELY RATED GFCI
RECEPTACLE WITH COVER.
3 of 4 FEIT ELECTRIC COMPANY | PICO RIVERA, CA | [phone] | FAX [phone] | www.feit.com 2 of 4 FEIT ELECTRIC COMPANY | PICO RIVERA, CA | [phone] | FAX [phone] | www.feit.com