Feit Electric WORK12000XLTPPLUG User manual

IMPORTANT SAFETY INSTRUCTIONS
AND INSTALLATION GUIDE
Item #: WORK12000XLTPPLUG
Dual Head Work Light with Metal Tripod
READ BEFORE INSTALLATION
SAVE THESE INSTRUCTIONS
Questions, problems, missing parts? Before returning to the store,
call Feit Electric Customer Service
8 a.m. - 5 p.m., PST, Monday - Friday
We appreciate the trust and confidence you have placed in Feit Electric through the purchase of this Dual Head Work Light. We strive to continually create quality products
designed to enhance your home. Visit us online to see our full line of products available for your home improvement needs.
Thank you for choosing Feit Electric.
1-866-326-BULB (2852)
FEIT.COM

Table of Contents ................................... 2
Safety Information .................................. 2
FCC Statement ...................................... 2
Warranty .......................................... 2
Pre-Assembly ...................................... 3
Assembly ......................................... 4-5
Limited Warranty
Table of Contents
This product is warranted to be free from defects in workmanship and materials for up to 3 years from date of purchase. If the product fails within the warranty period,
please contact Feit Electric at [email protected], visit feit.com/contact-us or call 1-866 326-BULB (2852) for instructions on replacement or refund. REPLACEMENT OR REFUND
IS YOUR SOLE REMEDY. EXCEPT TO THE EXTENT PROHIBITED BY APPLICABLE LAW, ANY IMPLIED WARRANTIES ARE LIMITED IN DURATION TO THE DURATION OF THIS
WARRANTY. LIABILITY FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES IS HEREBY EXPRESSLY EXCLUDED. Some states and provinces do not allow the exclusion of
incidental or consequential damages, so the above limitation or exclusion may not apply to you. This warranty gives you specific legal rights, and you may also have other
rights which vary from state to state or province to province.
2 WWW.FEIT.COM
Please contact 1-866-326-BULB (2852) for further assistance.
Important Safety Information
READ ALL INSTRUCTIONS
SAVE THESE INSTRUCTIONS
WARNING: RISK OFSHOCK. House electric current can
causepainful shock or serious injury unless handled properly.
WARNING: When using outdoor use portable luminaires,
basic safety precautions should always be followed to reduce
the risk of fire, electric shock, and personal injury.
WARNING: Use only three-wire extension cords that have
three-prong grounding plugs and grounding receptacles that
accept the appliance’s plug. Do not use an extension cord near
water or in areas where water may accumulate. Keep away
from pools or spas. Keep plugs dry.
Follow all safe guards stated in the manual, in addition to normal safety precautions
in working with electrical devices. Always follow basic safety precautions to reduce
the risk of fire, electric shock and personal injury.
All Safety and Operating instructions in this manual must be followed before using
this product.
To disconnect, turn off the switch, then remove the plug from the outlet.
Do not turn off by pulling on the cord.
•
•
Ground Fault Circuit Interrupter (GFCI) protection is to be provided on the circuit(s) or
for the wet location portable luminaire. Receptacles are available having built-in
GFCI protection and are able to be used for this measure of safety
•
Use only with an extension cord for outdoor use, such as an extension cord of cord type
SEW, SEOW,SEOOW, SOW, SOOW, STW, STOW, STOOW, SJEW, SJEOW, SJEOOW, SJW,
SJOW, SJOOW, SJTW, SJTOW, or SJTOOW.
•
•
To reduce the risk of fire, keep away from combustible materials while in operation.
•
To reduce the risk of injury, close supervision is necessary when this product is
used near children.
•
Suitable for Wet Locations
•
CAUTION: This portable light-emitting diode (LED) luminaire
has a polarized plug (one blade is wider than the other) as a
feature to reduce the risk of electric shock. This plug will fit in
a polarized outlet only one way. If the plug does not fully fit in
the outlet, reverse the plug. If it still does not fit, contact a
qualified electrician. Do not alter the plug.
Maintenance and Care
Maintenance of this work light is very minimal. Regularly clean the lens with a non-abrasive cleaning cloth. The same care should be provided for the stand.
Supplier’s Declaration of Conformity:
47 CFR § 2.1077 Compliance Information
Responsible Party: Feit Electric Company
4901 Gregg Road, Pico Rivera, CA 90660, USA
562-463-2852
Unique Identifier: WORK12000XLTPPLUG
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following
measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected. Consult the dealer or an experienced radio/TV technician for help. Any changes or modifications not expressly approved by the manufacturer could void the user's authority to operate the equipment.

3
Pre-Assembly
AA BB
PARTS INCLUDED
PARTS OF THE DUAL HEAD WORK LIGHT
NOTE: Parts not shown to actual size.
Part Description Quantity
AA 2
1
1
LED Work Light Body
BB Tripod
Lamp Mounting Bar
2DD
CC
Locking Knobs
4EE Split Lock Washers
4FF Washers
1GG Carrying Handle
1HH Hex Key Allen Wrench
1II Handle Locking Knob
2JJ Hex Screws
4KK Triangular Locking Knobs
1LL Tripod Locking Knob
WWW.FEIT.COM
Please contact 1-866-326-BULB (2852) for further assistance.
DD
CC
EE FF GG
HH JJ KKII LL
Back of the Work Light
Power Button
Carrying handle
LED Work Light Body
Lens
Lamp Mounting Bar
Tripod
Locking Knobs
Triangular
Locking
Knobs
Bracket Lock
Tripod Locking Knob
Height Adjustment Knobs

Assembly
LL
4 WWW.FEIT.COM
Please contact 1-866-326-BULB (2852) for further assistance.
Loosen the Tripod Locking Knob (LL) and move the three legs out
and down, then tighten the Tripod Locking Knob (LL) (See Fig. 1).
1Use the included Hex Wrench (HH) to remove the Hex Screws (JJ)
from the Lamp Mounting Bar (CC). Place the Carrying Handle (GG)
on the Lamp Mounting Bar (CC) and align it with the screw hole.
Place the Hex Screws (JJ) back and tighten them to hold the handle
in place (see Fig. 2).
2
Fig. 1 Fig. 2
JJGG
CC
3Place the Lamp Mounting Bar (CC) onto the Tripod (BB) and
secure it into place with the bracket lock (see Fig. 3). 4
Fig. 3
Bracket
Lock
Fig. 4
AA
DD
CC
EE
FF
Attach the LED Work light body (AA) to the lamp mounting bar
(CC) by first inserting the Split Lock washer (EE) and Washer
(FF) onto the Locking Knob (DD) and screwing the Locking Knob
(DD) through (AA) and into lamp mounting bar (CC) (see Fig. 4).
Tighten the Locking knob (DD) to set into place.
NOTE: The Locking Knobs (DD) must be loosened
first when placing the LED Work Light Body (AA)
on the Lamp Mounting Bar (CC). Re-tighten the
same Locking Knob (DD) to hold it into position
and repeat for the other side of the LED Work
Light Body (AA).

Assembly
5WWW.FEIT.COM
Please contact 1-866-326-BULB (2852) for further assistance.
Locking Knob
Horizontal Pivoting
To pivot horizontally loosen the center Locking Knob then
adjust to your preferred position. Once set to your
desired position, re-tighten the center Locking Knob to
lock it into place.
Vertical Pivoting
To pivot vertically loosen the two Triangular Locking Knobs
found on each side and adjust to your preferred position.
Once set to your desired position re-tighten both Triangular
Locking Knobs to lock it into place.
Triangular Locking Knobs
56Rotate the height adjustment knobs counter-clockwise
to loosen them and pull up the tripod to the desired
height. Rotate the height adjustment clockwise to
secure the tripod in place.
Height Adjustment
Loosen
and raise
Tighten
to secure
Insert the Handle Locking Knob (II) throught the Y-shape cord
and into the tripod. Turn the Handle Locking Knob (II) clockwise
to hold the Y-Shape cord in place (see Fig. 5).
Fig. 5
Y-Shape cord
II
7Once the LED Work Light Body (AA) has been attached to the Stand (BB), the LED Work Light can pivot vertically and horizontally into the
desired position.