Feiyu FY WG User manual

3
2
Manual Version 2.0
FY WG is a lightweight, yet feature-rich, wearable 3 axis gimbal capable of capturing immersive and fully stabilized footages. It is
compatible with GoPro HERO4/ 3+/ 3 (with optional mounting space for GoPro LCD BacPac) and other cameras with similar dimensions.
The FY WG is a miniaturized version of the best-selling FeiYu gimbal, offering exceptional stabilization technology in a wearable form factor
for action cameras. A GoPro T-Clamp adapter is packaged with every FY WG. Users can attach the gimbal to any accessories supporting
the GoPro three-prong mount. The FY WG also contains two 1/4"-20 tripod mounts on its gimbal body, allowing the gimbal to be mounted
in different orientations to all universal tripod screw mount accessories (including helmets, bikes, selfie sticks and other accessories).
Operation LED Status Function
* When the gimbal is in the Inverted Mode, pressing the function button three consecutive times will revert back to the original orientation.
When the battery is low, the gimbal will make three beeping sound and automatically shut down itself.
Turn On And Switch To
The Mode’s LED Status
Turn Off After
A moment
Power On
Sound
Two Beeps
Three Beeps Shutdown
The LED light will flash distinctively to indicate different operating modes.
Switch between different operating modes by pressing the function button.
Remove the screws on the
battery compartment,
insert two16340 batteries
and tighten the screws.
Mount the camera carefully
to the mounting bracket
and tighten the screws.
Ensure the camera is mounted securely. Press and hold the function button
for 2 seconds. The LED light will turn blue.
Press the function button and hold for 3 seconds, it will be powered off.
Function
Button
Function
Button
Operating Modes and Functions
Operating Modes and Functions
Function Button
（
ON / OFF ）
Tilting Axis Rolling Axis
Panning Axis
Function
Interface
1/4 Inch Screw Hole
1/4 Inch
Screw Hole
Screws For
The Battery
Compartment
Video And Camera
Charging Interface
T-Clamp Screw Hole
T-Clamp
Screw Hole T-Clamp
Screw Hole
Introduction
Install
4Accessories
Operation
1
Rolling
Tilting
Panning
Function
Button
Hexagonal Socket
Head Cap Screw
T-Clamp
Accessories For
1/4 Inch Screws
STEP 1
STEP 2 STEP 3
POWERING
ON / OFF
Use the 3M Adhesive to fix the bottom of the Gimbal.
Use with GoPro Accessories, mount the provided T-clamp to the side
or the bottom of the gimbal. Attach T-clamp to any accessories
supporting the standard GoPro three-prong mount.
The gimbal can also be mounted directly to other accessories using
the standard 1/4" tripod mount. Tighten all screws and ensure it is
firmly mounted before using the gimbal.
USB Cable
USB Connector
Extension Knurled
Thumb Screw
Charging
USB Cable
FY WG 3 Axis Wearable Gimbal is compatible with GoPro HERO4 / 3+ / 3 and cameras with
similar dimensions. Reserved mounting space for GoPro LCD Touch BacPac
Do not power on the
gimbal before completing
all the installation steps.
Do not power on the
gimbal before completing
all the installation steps.
!
WARNING !WARNING !
Camera stays in its current orientation. All panning, tilting and rolls are restricted.
Mode #1 - Panning Mode Camera is permitted to pan left or right. Vertical tilts or rolls are restricted.
Mode #2 - Panning and Til�ng Mode Camera is permitted to pan left or right and tilt up and down. Rolls are restricted.
Mode #3 - Lock Mode
Inversion Mode
Pressing the function button three consecutive times in any operating mode, the gimbal will switch to the
Inverted Mode (Allowing the user to flip the gimbal orientation upside down). Pressing the function button three more times
while in Inverted Mode to switch back to the original orientation
.
Manual Pulling Locking After the gimbal has been powered on for eight seconds, the tilt angle can be adjusted manually in the Panning Mode
and the Lock Mode. Adjust the title angle to the desired position and wait for 0.5 second until the gimbal registers the new angle.
Tilt and Level Calibra�on By using the optional G4 Remote Control, tilt and level can be adjusted without the need to connect to a computer.
For more information, please refer to G4 Remote Control section in the instruction manual.
Reset
Pressing the function button four consecutive times will reset the gimbal to initial orientation.
Long Press
For 1 Second
Long Press
For 2 Second
Long Press
For 3 Second
On Constantly
Operation LED Status
Function Explanation
Lock Mode
Function Button Quick Reference
Double Tap
Single Tap
LED Flashes Once
LED Flashes Twice
Panning Mode
Panning and Tilting Mode
Triple Tap
LED Flashes Once Inversion Mode
Quadruple Tap LED Flashes Once Reset
Charger
Input: DC 5V
Output: DC 4.2V
Type: 16340
M2*6mm
Rechargeable
Battery
Long screw
M 1.5 Allen Key T-Clamp
Quick-Release
Buckle
Curved Adhesive
Mounts 3M Adhesive
USB Power
Adapter
（Not Included）
Hexagonal
Socket Head
Cap Screw
Forward Inverted
Vertical Camera In LeftCamera In Left
Camera In Left
Camera in Right Camera in Right Camera in Right
3M
Adhesive
1
2
3
Please choose one way:
1
2
3
Video Output
and Camera
Charging Cable
Video
Output
Cable

5
UP LEFT RIGHTDOWN
Turn Off The Gimbal
FY Remote Control (Optional Item)
Mode #3 Lock Mode
USB Data Cable for RC
Function
Button
Direction
Button
Function
Interface Function
Interface
Operation
Explanation
Remark
Tap Button
Seven Times
Double Tap
Single Tap Mode #1 Panning Mode
Mode #2 Panning and Tilting Mode
Triple Tap Triple tap againInversion Mode
,exit inversion mode into original status
Quadruple Tap Reset
Long Press
For 1 Second
Long Press
For 3 Second
Direction Button
Note: The function button on the Gimbal will be disabled after connect the Remote Control
Steps to connect wireless remote control:
Keep the gimbal powered on, restart the remote control
and connect the receiver of RC to the gimbal, press the remote control
function button for 7 times in 5 seconds, if the indicator on the RC flashes
5 times it means the receiver and the transmitter of RC match successfully,
then customer can control the gimbal by the RC.
▲ RC needs to be match code whenever the following situations：（1）Connecting properly but still control in fail. （2）Change the receiver or wireless remote control.
Match Code
Install the receiver for wireless remote control: Insert the receiver for
wireless remote control into the function port of gimbal .
Open the wireless remote control: Long press the function button on
wireless remote control for one second to power on.
Open the gimbal: Long press the function button on gimbal for two
seconds to turn on the gimbal.
1
2
3
Use the wireless remote control to control the gimbal.
4
15 meters in an open environment.
Connect the Micro interface of wireless remote control with
5V charger by USB cable.
Charging
Remote Control Distance
Wireless
remote control
Receiver
for wireless
remote control
Joystick
Wireless Remote Control
Power
OFF
ON
Function
Button
Operation
Long press for
0.5 second
Long press for
3 seconds
Power on / off
Please install
the receiver
properly before
power on
!
Tip：The Remote Control will be
automatically powered off to
save battery if there is no operation
within three minutes.
Remote Control Operation Instructions
Wired remote control
Calibration Using Remote Control
Single tap ,exit calibration and enter standby. Wake the
gimbal by pressing the function button once again
Tap Button
Six Times
Match Code Mode
Match code when connecting properly but still control
in fail or change the receiver/wireless remote control.
Wireless RC
With the remote control, you can switch the gimbal mode or adjust the angle from a distance.
WARNING
Make sure that the
connec�on to the
computer is done by the
!
PC
!
Initialization Instructions
FY WG needs to be initialized whenever the
following situations are observed after power on
6Firmware Upgrade
8Initialize The Gimbal
7Video and Camera Charging Interface
Motionless Flat Surface
188 g (Without
Batteries & Camera)
800 mA
0.1 ~ 0.5
(Motor Overload<2G)
0.01 ~ 0.05
(Working Voltage)
3°/S ~ 150°/S
Camera Maximum Weight
150 g
Camera Maximum Thickness
31.7 mm
( Replaceable
mounting bracket )
Camera Maximum Height
43.6 mm
( Replaceable
mounting bracket )
Usage Time 3 ~ 4 Hours
2°/S ~ 75°/S
320°
6.0 V ~ 9 V
320°
100°
Parameters
53.4 mm
91 mm
35 mm
95 mm
Upgrade........
USB Cable
Function
Interface
Function
Interface
Please visit the official website of Feiyu Tech: www.feiyu-tech.com to download the USB driver, firmware upgrade software and the latest firmware.
Unzip the compressed file locally to your computer. Refer to the connection diagram on how to connect the gimbal with the computer. Please
follow the instructions inside the firmware upgrade package carefully, or there will be a risk of rendering the gimbal inoperable.
The tilt and level settings can be calibrated through the use of the configuration software. User can adjust the tilt and diagonal rotation in small intervals
to better adapt to his/her filming scene. Before any calibration, please insert the batteries into the gimbal and refer to the connection diagram to
connect the gimbal with the computer.
Firmware Upgrade Instruction
Tilt and Level Calibration
Be sure to insert the
batteries before upgrading
USB Connector
Attention : Please make sure that the connection to the computer is done by the USB connector.
Attention : Please make sure that the connection to the computer is done by the USB connector.
Video Output Cable Analog Monitor
( Equipped by users )
This interface can be output 5 voltage and receive analog video signal from GoPro
Connect the video output and camera charging cable as the above diagram
can power the GoPro camera and view video signal from the GoPro camera. Note: The Analog Monitor are equipped by users.
After connecting the video output and camera charging
cable, the analog monitor can be used as a display.
FY WG 3-Axis Wearable Gimbal is a feature-rich camera stabilizer, yet lightweight and portable.
It is prohibited for any user to use the gimbal for any illegal purposes.
Guilin Feiyu Electronic Technology Co.,Ltd and our associates assume no liability for any accident, injury,
death, loss, or other claim related to or resulting from the use of this product. In no event shall Guilin Feiyu
Electronic Technology Co.,Ltd and our associates be liable for incidental or consequential damages relating
to or resulting from the use of this product or any of its parts. Damage resulting from use, accident, or normal
wear and tear is not covered by our warranty.
Guilin Feiyu Electronic Technology Co.,Ltd reserves the right to amend this manual and the terms and
conditions of this product at any time.
Please assemble the gimbal in accordance to
the diagram provided.
Please upgrade the firmware and configuration
settings with the provided USB data cable.
Please charge the battery with the provided
battery charger.
Please install the camera securely before
powering on the gimbal.
DISCLAIMER
ATTENTION
1. Ensure gimbal is fully assembled and camera
is installed properly.
2. Place the gimbal on a flat surface and keep it
stationary.
3. Power on the Gimbal.
4. Wait for the gimbal to finish its initialization
before resuming the use of the gimbal.
1. The tilt angle is not leveled with the horizontal
surface.
2. The roll angle is not parallel to the horizontal
surface.
3. When the gimbal is Full-Axis-Lock mode,
the camera does not stay stationary.. When initialization is completed,
the LED light will quickly flash.
Note:
Working Voltage
Static Attitude
Tracking Accuracy
Motion Attitude
Tracking Accuracy
Overload Current
Protection
Vertical Tilting Angle
Rolls Angle
Horizontal Panning Angle
Tilting Increments
Panning Increments
Weight
Please visit the official website of Feiyu Tech
to get related information: www.feiyu-tech.com
Technical support: [email protected]
Everyone
Can Make a Movie