Fellowes Quasar E 500 User manual

• •
Please read these instructions before use.
Veuillez lire ces instructions avant utilisation.
Lea estas instrucciones antes del uso.
http://www.monomachines.com
http://www.monomachines.com
••
Please read these instructions before use.
Veuillez lire ces instructions avant utilisation.
Lea estas instrucciones antes del uso.

Comb----, /CF
L-- __ Waste tray
L----Comb storage
and Document
measure
~,,~~ ENGLISH
Waste tray
Comb storage and Document measure
CAPABILITIES
Punching Capacity
Paper sheets
70-BOg / 20lb
Transparent covers
100- 200 micron /4-B mil
200+ micron / B+ mil
Other standard covers
160-270g /40-60 Ib
270+g / 60+ Ib
Voltage:
Current:
Duty Cycle:
IMPORTANT SAFETY INSTRUCTIONS - Read Before Using!
IA(AUTlOI I
Please keep for future reference
When punching;
- always ensure the machine is on a stable surface
- test punch scrap sheets and set the machine before punching final documents
- remove staples and other metal articles prior to punching
- never exceed the machines quoted performance
Q
..
-~--J0
Document
support (lid) --- -+-J-+-{
~
:::::~~~f~§~~~~~~~8t =~paperentry
Adjustable Window
edge guide----f------,
,---- ~ ....... ~-- Overload neon
Wheel to adjust - --t----{(~~mmij~~m~~~~~~f~~_;~~ =-----power on neon
edge guide ~ On/off switch
opening
lever
20 sheet
3 sheet
2 sheet
3 sheet
2 sheet
120V AC 60Hz
2A
30 Minutes On /30 Minutes Off
Binding Capacity
Max com b size
Max document (BOg /20Ib)
Technical Data
Paper dimensions
Punching slots
Slot pitch
Adjustable edge guide
Waste tray capacity
Motor wattage
Net weight
Dimensions (LxDxH)
Keep the machine away from heat and water sources.
Never attempt to open or otherwise repair the machine.
Plug the machine into an easily accessible socket.
Turn off the machine after each use
Unplug the machine when not in use for an extended period.
Note - this machine features a thermal cut-out device which activates when the
machine is overheated during use. It will automatically reset when the machine is
safe to operate.
2"/50mm
c. 500 sheet
US letter
19
14.2Bmm / 9/16"
yes- rotary
tbc
115
9.5 kg/20.9Ib
460 x 390 x 130mm / lB.l" x 15.3" x 5.1"
2
http://www.monomachines.com
http://www.monomachines.com
ENGLISH
Q
..
L-- __ Waste tray
o
L----Comb storage
and Document
measure
~
::::::~~~f~§~~~~~~~8t=~paperentrY
Adjustable Window
edge guide----f-----,
,-------f"' ...... l---- Overload neon
Wheel to adjust ---t-F-J,1;m1Jijm~m~~~~~~f~~-;~~=-----power on neon
edge guide ~ On/off switch
~~~~~~~~~~I~~~~~~d~L_punch button
Document
support (lid) ----+-J-+-{
Comb----,/CF
opening
lever
Waste tray
Comb storage and Document measure
CAPABILITIES
Punching Capacity
Paper sheets
Binding Capacity
Max com b size 2"/50mm
70-80g / 20lb 20 sheet
Max document (80g /20Ib)
c. 500 sheet
Transparent covers
100- 200 micron /4-8 mil 3 sheet
Technical Data
Paper dimensions
US letter
200+ micron / 8+ mil 2 sheet
Punching slots
19
Other standard covers
160-270g /40-60 Ib
270+g / 60+ Ib
Voltage:
Current:
3 sheet
2 sheet
120V AC 60Hz
2A
Slot pitch
Adjustable edge guide
Waste tray capacity
Motor wattage
Net weight
Dimensions (LxDxH)
14.28mm / 9/16"
yes- rotary
tbc
115
9.5 kg/20.9Ib
460 x 390 x 130mm / 18.1" x 15.3" x 5.1"
Duty Cycle:
30 Minutes On /30 Minutes Off
Please keep for future reference
IMPORTANT SAFETY INSTRUCTIONS - Read Before Using!
IACAUTIO I
When punching;
- always ensure the machine is on a stable surface
- test punch scrap sheets and set the machine before punching final documents
- remove staples and other metal articles prior to punching
- never exceed the machines quoted performance
Keep the machine away from heat and water sources.
Never attempt to open or otherwise repair the machine.
Plug the machine into an easily accessible socket.
Turn off the machine after each use
Unplug the machine when not in use for an extended period.
Note - this machine features a thermal cut-out device which activates when the
machine is overheated during use. It will automatically reset when the machine is
safe to operate.
2

COMB DIAMETER & DOCUMENT SIZES
Comb diameter sizes
.' ,"
(§
~
mm inch number of pages
6mm 1/4"
2-20
Need Help?
8mm 5/16"
21-40
Customer Service ...
vvvvw .fello w es.com
Let our experts help you
10mm 3/8"
41-55
w ith a solution.
AWiays call Fellowes
12mm 1/2"
56-90
before contacting
your place of purchase.
16mm 5/8"
91-120
18mm 11/16"
121-150
22mm 7/8"
151-180
25mm
1"
181-200
32mm 1 1/4"
201-240
38mm 1 1/2"
241-340
45mm 1 3/4"
341-410
51mm
2" 411-500
SET UP
3 "'1
1 4
2_ Check waste tray is empty
and correctly filled_
1_ Ensure the machine is on a 3. Please connect power cable to
4_ Plug the machine into an
stable surface_ inlet at back of laminator_
easily accessible mains socket.
Switch the mains supply on_
5_ Switch the machine on (located
at the rear of the machine)
6_ lift the lid_ Check the green
power light is on_
7_ Ensure the comb-opening
lever is pushed backwards_
3
http://www.monomachines.com
http://www.monomachines.com
COMB DIAMETER & DOCUMENT SIZES
Comb diameter sizes
~
~
. . .
mm inch number of pages
6mm 1/4"
2-20
8mm 5/16"
21-40
10mm 3/8"
41-55
12mm 1/2"
56-90
16mm 5/8"
91-120
18mm 11/16"
121-150
22mm 7/8"
151-180
25mm
1" 181-200
32mm 1 1/4"
201-240
38mm 1 1/2"
241-340
45mm 1 3/4"
341-410
51mm
2" 411-500
Need Help?
Customer service ...
_w.fellowes.com
Let our experts help you
with a solution.
AWiays call Fellowes
betore contacting
your place ot purchase.
SET UP
4
3-r
1
1. Ensure the machine is on a
stable surface.
2. Check waste tray is empty
and correctly filled.
3. Please connect power cable to
inlet at back of laminator.
4. Plug the machine into an
easily accessible mains socket.
Switch the mains supply on.
5. Switch the machine on (located
at the rear of the machine)
6. lift the lid. Check the green
power light is on.
7. Ensure the comb-opening
lever is pushed backwards.
3

~,,~~ ENGLISH
BEFORE YOU BIND
1. Check the green power neon is on.
2. Select the correct comb diameter
using the comb storage tray.
3. Insert the plastic comb into the
opening mechanism.
4. Pull comb-opening lever forward to
open the comb.
STEPS TO BIND
1
Front
(over
C
,~;,'
-'-~-_Cc_~-_~ /~ Buck
(over
1. Punch front and back covers
first.
5. Test punch scrap sheets to check
edge gUide selling.
2
MAX 20
(80gsm)
2. Punch sheets in small
batches that do not overload
the machine or the user.
3. load punched sheets directly
onto the opened comb. Starting
with the front of the document.
4. When all punched sheets are
loaded onto the comb, push the
comb lever backwards to close
the comb and remove the bound
document.
4
http://www.monomachines.com
http://www.monomachines.com
ENGLISH
BEFORE YOU BIND
1. Check the green power neon is on.
4. Pull comb-opening lever forward to
open the comb.
STEPS TO BIND
1
Front
(over
Bock
(over
2
2. Select the correct comb diameter
using the comb storage tray.
5. Test punch scrap sheets to check
edge guide selling.
MAX 20
(80gsm)
3. Insert the plastic comb into the
opening mechanism.
4
1. Punch front and back covers
first.
2. Punch sheets in small
batches that do not overload
the machine or the user.
3. load punched sheets directly
onto the opened comb. Starting
with the front of the document.
4. When all punched sheets are
loaded onto the comb, push the
comb lever backwards to close
the comb and remove the bound
document.

CORRECTING A BOUND DOCUMENT
Additional sheets may be include or removed at any time by opening and then closing the comb as previously described.
REMOVAL OF WASTE CLIPPINGS
The waste tray is located under the machine and is accessed from the right side. For best results empty the tray regularly.
STORAGE
Switch off the machine. lower the lid. The Quasar-E comb binder is designed to be stored horizontally on the desk.
TROUBLESHOOTING
Problem
Cause Solution
No Green power light
Machine is not switched on Switch on machine at rear next to plug inlet and at the socket
Red standby light
Machine is overloaded when punching Press the punch bullon. The machine will withdrow the punches
and re-set itself. Continue this process until the punch cycle is
complete
Punched holes are not centrol
Edge gUide not set Adjust edge gUide until hole pallern is correct
Machine will not punch
Blockage Check waste troy is empty. Check for blockage to paper entry.
Punch holes are not parollelto edge
Debris is stuck below dies Take stiff cardboard and slide into the paper entry. Move the
cardboard sideways to release any stroy clippings into the
waste troy
Partial holes
Sheets not correctly aligned to punch pallern Adjust edge gUide and test punch scrap sheets until correct
Damaged hole edges
Possibly overloading the machine Punch plastic covers with paper sheets. Reduce number of
sheets being punched
Waste troy leaks
Waste troy is not correctly inserted or 'burst
Check waste troy is empty and 'burst feature' is closed
feature' has activated
WARRANTY
Fellowes warrants all parts of the binder to be free of defects in material and workmanship warranty period set forth above. In no event shall Fellowes be liable for any consequential
for 2 years from the date of purchase by the original consumer. If any part is found to be damages attributable to this product. This warranty gives you specific legal rights. You may
defective during warranty period, your sale and exclusive remedy will be repair or replacement, have other legal rights that vary from this warranty. The duration, terms and conditions of this
at Fellowes' option and expense, of the defective part. This warranty does not apply in warranty are valid worldWide, except where different limitations, restrictions or conditions may
cases of abuse, mishandling or unauthorised repair. Any implied warranty, including that of be required by local law. For more details or to obtain services under this warranty, please
merchantability or fitness for particular purpose, is hereby limited in duration to the appropriate contact Fellowes or your dealer.
s
http://www.monomachines.com
http://www.monomachines.com
CORRECTING A BOUND DOCUMENT
Additional sheets may be include or removed at any time by opening and then closing the comb as previously described.
REMOVAL OF WASTE CLIPPINGS
The waste tray is located under the machine and is accessed from the right side. For best results empty the tray regularly.
STORAGE
Switch off the machine. lower the lid. The Quasar-E comb binder is designed to be stored horizontally on the desk.
TROUBLESHOOTING
Problem
No Green power light
Red standby light
Punched holes are not central
Machine will not punch
Punch holes are not parallel to edge
Partial holes
Damaged hole edges
Waste tray leaks
WARRANTY
Cause
Machine is not switched on
Machine is overloaded when punching
Edge guide not set
Blockage
Debris is stuck below dies
Sheets not correctly aligned to punch pallem
Possibly overloading the machine
Waste tray is not correctly inserted or 'burst
feature' has activated
Solution
Switch on machine at rear next to plug inlet and at the socket
Press the punch bUllon. The machine will withdraw the punches
and re-set itself. Continue this process until the punch cycle is
complete
Adjust edge guide until hole pallem is correct
Check waste tray is empty. Check for blockage to paper entry.
Take stiff cardboard and slide into the paper entry. Move the
cardboard sideways to release any stray clippings into the
waste tray
Adjust edge guide and test punch scrap sheets until correct
Punch plastic covers with paper sheets. Reduce number of
sheets being punched
Check waste tray is empty and 'burst feature' is closed
Fellowes warrants all parts of the binder to be free of defects in material and workmanship
for 2 years from the dote of purchase by the original consumer. If any part is found to be
defective during warranty period, your sale and exclusive remedy will be repair or replacement,
at Fellowes' option and expense, of the defective part. This warranty does not apply in
cases of abuse, mishandling or unauthorised repair. Any implied warranty, including that of
merchantability or fitness for particular purpose, is hereby limited in duration to the opprapriote
warranty period set forth above. In no event sholl Fellowes be liable for any consequential
damages attributable to this praduct. This warranty gives you specific legal rights. You may
have other legal rights that vary from this warranty. The duration, terms and conditions of this
warranty are valid worldwide, except where different limitations, restrictions or conditions may
be required by local low. For more details or to obtain services under this warranty, please
contact Fellowes or your dealer.
s

Help Line
Australia
+ 1-800-33-11-77
Canada + 1-800-665-4339
Europe 00-800-1810-1810
Fellowes
Australia
+ 61-3-8336-9700
Benelux
+ 31-[0)-76-523-2090
Canada + 1-905-475-6320
Deutschla nd
+ 49-[0)-5131-49770
Espana + 34-91-748-05-01
France + 33-[0)-1-30-06-86-80
Italia + 39-071-730041
Mexico + 1-800-234-1185
United States
+ 1-800-955-0959
Japan + 81-[0)-3-5496-2401
Korea + 82-2-3462-2884
Malaysia + 60-[0)-35122-1231
Polska + 48-[0)-22-771-47-40
Singapore
+ 65-6221-3811
United Kingdom
+ 44-[0)-1302-836836
United States
+ 1-630-893-1600
http://www.monomachines.com
http://www.monomachines.com
Help Line
Australia
[phone] Mexico [phone]
Canada [phone] United States
[phone]
Europe 00-800-1810-1810
Fellowes
Australia
[phone] Japan +81-[0)-3-5496-2401
Benelux
+31-[0)-76-523-2090 Korea [phone]
Canada [phone] Malaysia +60-[0)-35122-1231
Deutschla nd
+49-[0)-5131-49770 Polska +48-[0)-22-771-47-40
Espana [phone] Singapore
[phone]
France +33-[0)-1-30-06-86-80 United Kingdom
+44-[0) -1302-836836
Italia [phone] United States
[phone]