Fellowes Star Plus 150 User manual

Small Office Comb Binder
please read these iNstruCtioNs beFore use.
do Not disCard: keep For Future reFereNCe.
veuillez lire Ces iNstruCtioNs avaNt d’utiliser l’appareil.
Ne pas jeter : CoNserver aFi N de CoNsulter les direCtives ultéri-
euremeNt, eN Cas de besoiN.
lea estas iNstruCCioNes aNtes del uso.
No las deseChe: CoNsérvelas Como reFereNCia Futura.

1
CORRECTING A BOUND DOCUMENT REMOVAL OF WASTE CLIPPINGS
WARRANTY
Fellowes warrants all parts of the binder to be free of defects in material and workmanship for 2 years from
the date of purchase by the original consumer. If any part is found to be defective during warranty period,
your sale and exclusive remedy will be repair or replacement, at Fellowes’ option and expense, of the defec-
tive part. This warranty does not apply in cases of abuse, mishandling or unauthorised repair. Any implied
warranty, including that of merchantability or fitness for particular purpose, is hereby limited in duration to
the appropriate warranty period set forth above. In no event shall Fellowes be liable for any consequential
damages attributable to this product. This warranty gives you specific legal rights. You may have other legal
rights that vary from this warranty. The duration, terms and conditions of this warranty are valid worldwide,
except where different limitations, restrictions or conditions may be required by local law. For more details or
to obtain services under this warranty, please contact Fellowes or your dealer.
3
SET UP
TROUBLESHOOTING
Problem
Punched holes are not central
Machine will not punch
Punch holes are not parallel to edge.
Partial holes
Damaged hole edges
Waste tray leaks
Cause
Edge guide not set
Blockage
Debris is stuck below dies.
Sheets not correctly aligned to punch pattern.
Possibly overloading the machine
Waste tray is not correctly inserted or ‘burst feature’ has activated
Solution
Adjust edge guide until hole pattern is correct
Check waste tray is empty. Check for blockage to paper entry.
Take stiff cardboard and slide into the paper entry. Move the cardboard sideways
to release any stray clippings into the waste tray.
Adjust edge guide and test punch scrap sheets until correct
Punch plastic covers with paper sheets. Reduce number of sheets being punched.
Check waste tray is empty and ‘burst feature’ is closed.
1. Ensure the machine is on a
stable surface. 2. Check waste tray is empty and correctly fitted. 3. Lift the lid. Ensure the comb- opening lever is pushed backwards. 4. Lift the punch handle to its upright position.
BEFORE YOU BIND
1. Select the correct comb diameter
using the comb storage tray. 2. Insert the plastic comb into the mechanism. 3. Pull comb-opening lever forward to open the comb. 4. Test punch scrap sheets to check edge guide setting.
STEPS TO BIND
3. Load punched sheets directly
onto the opened comb. Starting
with the front of the document.
4. When all punched sheets are loaded
onto the comb, push the comb lever
backwards to close the comb and
remove the bound document.
2 3 4
2 3 4
21 3 4
Additional sheets may be included or removed at any time by opening and
then closing the comb as previously described. The waste tray is located under the machine and is accessed from the right side. For best results empty the tray regularly.
STORAGE
30
30
Front
Cover
Back
Cover
30
Max 15
(75gsm/20lbs)
1. Ensure edge guide is set to the
proper document size. Punch front
and back covers first.
2. Punch sheets in small batches
that do not overload the machine
or the user. Adjust edge guide, if
necessary.
Lower the punch handle to the horizontal position. Lower the lid. The Star+ comb binder is designed to be stored horizontally or vertically.
There are feet that enable them to stand upright.

Waste tray
Comb storage
and Document
measure
mm inch number of pages
6mm 1/4” 2-20
8mm 5/16” 21-40
10mm 3/8” 41-55
12mm 1/2” 56-90
16mm 5/8” 91-120
18mm 1 1/16” 121-150
ENGLISH
CAPABILITIES
IMPORTANT SAFETY INSTRUCTIONS
When punching;
- always ensure the machine is on a stable surface
- test punch scrap sheets and set the machine before punching final documents
- remove staples and other metal articles prior to punching
- never exceed the machines quoted performance
COMB DIAMETER & DOCUMENT SIZES
2
Punching Capacity
Paper sheets
75g / 20lb 15 sheets
Transparent covers
100-200 micron / 4-8 mil 2 sheets
200+ micron / 8+ mil 2 sheets
Other standard covers
160-270g / 40-60 lb 3 sheets
270+g / 60+ lb 2 sheets
Binding Capacity
Max comb size 11/16” (80mm)
Max document (75g / 20lb) 150 sheets
Technical Data
Paper dimensions US letter
Punching slots 19
Slot pitch 14.28mm / 9/16”
Adjustable edge guide yes
Waste tray capacity 600 sheets
Net weight 4.5 kg / 10lb
Dimensions (HxWxL) 80 x 450 x 250mm / 3.1” x 17.7” x 9.8”
Please keep for future reference.
Comb diameter sizes
75g
20lb
Read Before Using!
Need Help?
Customer Service….
www.fellowes.com
Let our experts help you
with a solution.
Always call Fellowes
before contacting
your place of purchase.
Comb storage and Document measure
Document
support (lid)
Punch handle
Window
Comb
opening
lever
Carry handle
Paper entry
Waste tray
Adjustable
edge guide