Femco WEATHERBRAKE 307022173 User manual

INSTRUCTIONS
WEATHERBRAKE
307022173
FITS
General Offices
1132 W. 1ST STREET
McPherson, KS 67460
Phone: [phone]
Web: www.femcomfg.com Form No. 286324200 / 11-2005
MT295, MT297, MF1445, MF1455 & ST45

1. Attach yoke brace (A) to tubing using four (4) M8 bolts.
2. Attach yoke brackets (B) to yoke brace using two (2)
1/4” x 3/4” bolts and nuts. Note: Long flange to top.
3. Tighten bolts.
YOKE BRACKETS
1. Remove bolt from front of platform.
2. Attach door post (A) to platform using bolt removed.
Repeat procedure for the other side.
3. Tighten bolts.
DOOR POST
IMPORTANT
CAREFULLY STUDY THE PHOTO DIAGRAMS SHOWING THE
LOCATION OF EACH PART. LEAVE ALL HARDWARE LOOSE
UNTIL INSTRUCTED TO TIGHTEN.
A
B
A

1. Arrange motor cover over hood of tractor.
2. Slide 3” hem of motor cover down over top of door
post.
MOTOR COVER
1. Insert yoke (A) into top 3” hem of motor cover.
2. Attach yoke to yoke bracket using two (2) 1/4” x 3/4”
bolts and nuts
3. Attach yoke to door post using one (1) 1/4” x 1” bolt
and nut. Note: Head of bolt inside, nut outside.
4. Tighten center bolts only.
YOKE
A
1. Cut plastic Dual Lock® into 2” lengths.
2. Surface must be cleaned with a mild detergent to as-
sure proper application of Dual Lock® strips.
NOTE: Do not peel the backing from the Dual Lock® .
3. Apply cut Dual Lock® to all Dual Lock® sewn to motor
cover.
4. Arrange motor cover to tractor. Peel backing from Dual
Lock® and apply to tractor. Repeat this procedure for
all Dual Lock® .
DUAL LOCK® is a registered trademark of the 3M Co.

1. Thread cloth strap through grommets at bottom of mo-
tor cover and tie.
2. Route cloth straps to other side or to a point on tractor
and tie.
IMPORTANT
Cloth straps are not to be attached to any moving, ro-
tating, or heat generating points of tractor. Any excess
cloth strap is to be cut off.
TIE STRAPS
1. Attach left and right window frames using two (2) #10 x
3/4” bolts and nuts.
2. Slide glass into the channel of the windshield.
3. Attach flat strip and angle strip to the windshield using
two (2) #10 x 3/4” bolts and nuts.
WINDSHIELD ASSEMBLY
1. Remove nut from yoke and door post and attach as-
sembled windshield.
2. Attach other side of windshield to yoke using one (1)
1/4” x 1” bolt and nut.
3. Tighten all bolts.
WINDSHIELD ATTACHMENT

1. Locate holes in door post and cut holes in the fabric.
2. Hold door (A) to door post and bottom of the wind-
shield.
3. Mark location of holes in the door post to the door.
4. Cut 5/8” slots next to wire frame of door and attach to
door post using four (4) #10 x 3/4” bolts, clips and nuts.
5. Tie door flap (B)
6. Tighten all bolts.
DOORS
A
B
1. Mark location of holes in windshield to side window (A).
2. Cut 5/8” slots next to wire frame of window and attach
to windshield using #10 x 3/4” bolts, clips and nuts.
3. At location (B), cut 5/8” slots inside window and top of
door and attach using #10 X 3/4” bolt, clip and nut.
4. Repeat procedure for other side.
5. Tighten all bolts.
SIDE WINDOWS
A
1. Remove loader valve and attach loader valve plate (A)
using 5/16” x 1” bolts.
2. Attach loader valve and tighten all bolts.
LOADER VALVE PLATE
B
A

1. Assemble door latches as shown using two (2) 1/4” x
3/4” bolts and nuts.
2. Position under bottom rear of door.
3. Door is to be set firmly in loop of door latch. Change
position up or down with adjustment holes if necessary.
4. Mark location for one (1) of the two (2) holes and drill
one (1) 9/32” diameter hole
5. Attach to fender using one (1) 1/4” x 1” bolt and nut.
6. Tighten all bolts.
DOOR LATCH
NOTES