Fender KXR 200 User manual

KXR 200
SERVICE MANUAL
CONTENTS:
Notices
Specifications
Circuit description
Parts lists:
Preamp PCB assembly
Pwr amp PCB assembly
Chassis assembly
Cabinet assembly
Miscellaneous
Schematics/diagrams
Fender Musical Instruments Corp. 7975 North Hayden Road Scottsdale, AZ 85258

KXR 200
(This is the model name for warranty claims)
SERVICE MANUAL
MARCH 1996
IMPORTANT NOTICE:
The information contained herein is CONFIDENTIAL and PROPRIETARY to Fender Musical Instruments Corp. It is
disclosed solely for use by qualified technicians for purposes of equipment maintenance and service. It is not to be
disclosed to others without the expressed permission of Fender Musical Instruments Co. All specifications subject to
change without notice.
For warranty repair service, only Fender specified part numbers are to be used. It is recommended they also be used
for post-warranty maintenance and repair.
Parts marked with an asterisk (*) indicate the required use of that specific part. This is necessary for RELIABILITY
and SAFETY requirements. DO NOT USE A SUBSTITUTE!
A coded naming convention is used in the description of certain parts. The codes and what they mean are as follows:
CAPACITOR CODES HARDWARE CODES
CAP AE = Aluminum Electrolytic BLX = Black Oxide
CAP CA = Ceramic Axial CR = Chrome Plated
CAP CD = Ceramic Disk HWH = Hex Washer Head
CAP MPF = Metalized Polyester Film M = Machine Screw
CAP MY = Mylar NI = Nickel Plated
CAP PFF = Polyester Film/Foil OHP = Oval Head Phillips
PB = Particle Board
RESISTOR CODES PHP = Pan Head Phillips
PHPS = Pan Head Phillips Sems
RES CC = Carbon Comp SMA = Sheet Metal "A" Point
RES CF = Carbon Film SMB = Sheet Metal "B" Point
RES FP = Flame Proof SS = Stainless Steel
RES MF = Metal Film TF = Thread Forming
RES WW = Wire Wound ZI = Zinc Plated

KXR 200
SPECIFICATIONS
Product Release No.: PR 286 (This is not a model number)
Power output: 200 Watts RMS
Distortion at 200 watts: Less than .1% @ 1kHz, below compression
Less than 1% @ 1kHz, maximum compression
Rated Load Impedance: 4 Ω
Input impedance: 22K Ohms
Sensitivity: 1.03V RMS
DELTACOMP Range: 20dB
PREAMP SECTION:
Input Impedance: XLR – 1.82K Ω
Phone – 18.2k Ω
Senitivity for 200 watts: XLR – 2.9mV RMS
Channel and master Phone – 29mV RMS
Volume at maximum, all
Tone controls at “0”
Equalizer: For 3-band-EQ sections:
+/- 12dB at 130,540 and 4200 Hz
Sensitivity for channel 500mV RMS (-6dBV)
Inserts, Master volume
At maximum setting
Sensitivity for Master 130mV RMS (-18dBV)
Volume and FX return
Control at maximum
Dimensions:
Height:29 3/4" (75.6 cm) (w/o casters)
Width: 21 11/16" (55.1 cm)
Depth: 12" (30.5 cm)
Weight: 88 lbs. (40.0 kg)
Product specifications are subject to change without notice

KXR 200
CIRCUIT DESCRIPTION
PREAMPLIFIER
Input channels 1 thru 3 will accept a balanced or unbalanced signal via a ¼” phone jack. Resistors R1 &
R2 are precision 1% parts which maximize the Common Mode Rejection of the first opamp stage U1A.U1A
provides a gain of 1, and rolls off high frequencies above 87kHz. The signal then couples to the 3 band
equalizer circuit. Gyrator U2A is tuned to 130 Hz (LOW), and Gyrator U2B to 540Hz (MID). The HIGH
control uses C10 and R14 to provide a 6dB per octave shelving filter above 4.2kHz. The boost/cut function
is handled by U3A. The signal couples to the Volume control stage U1B. The Volume control (R17) varies
the gain from less than 1 to about 23. The signal is then routed through a ribbon cable to the Channel
Insert Jack J2. This 3 conductor Phone jack sends the signal out on the “Tip” contact, and accepts the
return signal on the “Ring” contact. The signal then couples through C14 to the FX SEND bus, REVERB
SEND bus, and MAIN bus.
Although similar to channels 1 thru 3, Input channel 4 features the addition of an XLR jack which will accept
a balanced low impedance microphone input. Channel 4 also features a 4-band equalizer circuit. Gyrator
U11A is tuned to 125Hz (LOW), gyrator U11B is tuned to 320 Hz (LOW MID), and gyrator U12A to 1kHz
(HIGH MID). The HIGH control uses C56 and R92 to provide a 6dB per octave shelving filter above 3.2
kHz.
The signals from the FX SEND controls are summed at U13A, which provides a gain of 2 and drives the FX
SEND jack (J10). To minimize noise, the FX RETURN jack (J11) contains a switch contact that grounds
the signal line when the return jack is not being used. U13B provides a gain of less than 1 to a maximum
gain of 5. The FX return signal sums with the main signal at U14A.
The signals from the REVERB SEND controls are summed at U6A, which provides a gain of 2 and feeds
the reverb pan drive circuit at U6B. U15A makes up the reverb recovery circuit. U15b provides variable
gain and drive U14A. U14A is the summing amplifier for the Main, Effects Return, and Reverb return
signals. It provides a maximum gain of about 2, feeds U14B, and drives the Line Output jacks. The Line
Ouputs provide a pseudo-balanced signal. U14B feeds signal to the power amplifier.
The signal form the preamp feeds from P1B pin 4, through a ribbon cable, to P1A on the power amplifier
PCB. The signal couples (via C1) to the unity gain amplifier U1B. U1B contains a closed loop (gain of 1)
negative feedback path, along with positive feedback through the inverting Operational Transconductance
Amplifier(OTA) U2. U1B and U2 make up the gain reduction circuit for the DeltaComp clip protection
feature.
The attack and release circuit for the DeltaComp is made up by the Diode, Resistor, and Capacitor network
which drives the Base of Q19. Comparator U1A senses the voltage from the Collectors of Q20 & Q21.
When the power amplifier approaches clipping on a positive swing, the collector of Q5 pulls up R56, which
turns on Q20, transferring –16vdc to the collector, pulling down R60. This causes the output (pin 1) of U1A
to switch from +15vdc to –15vdc, lighting the DeltaComp/Clip LEd. Note when the DeltaComp is disabled,
the Led indicates clipping of the output stage. With the DeltaComp enabled, the Led indicates an active
DeltaComp circuit. The negative control voltage from R60 also feeds through P1A to P1B on the preamp
PCB. The voltage is routed to the DeltaComp switch (S5A), located on the front panel. With the switch
engaged, the control voltage is sent back through the ribbon cable (via P1 pin 6) to the attack/release
circuit.
The negative voltage drives through Diodes CR31-CR34, and charges Capacitors C16-C19 all at once in
parallel as a one pole filter through a single time constant of R60 x (c16+17+18+19) or 2.2k x
8.8Uf=19.4mSec. As they charge, Q19 turns on and provides current to pin 5 of the QTA (U2). The

KXR 200
DELTACOMP (CONT)
current controls the output amplitude of U2. The inverted signal from U2 mixes with the input to U1B
providing cancellation which reduces the input to the power amplifier. This prevents the amplifier from
clipping. When the output of the power amplifier is reduced, the output of U1A toggles back to +15dvc.
Due to the blocking action of Diodes CR31-CR34, Capacitors C16-C19 are forced to discharge as a 4-pole
filter with different time constants through R55. R51 prevents Parasitic oscillation white Zener CR30
provides 2 slopes which results in smoother limiting.
When the power amplifier approaches clipping on a negative swing, R62 is pulled low, turning on Q22
which pulls up the Base of Q21 transferring –16vdc to the collector.
POWER AMPLIFIER
JFET Q1 and associated components provide a 4-5 second turn-on delay for the audio input to the power
amplifier. When the power is switched on, Capacitor C5 charges through Resistor R7. The negative Gate
voltage pinches off the JFET, removing the ground from the input of the amplifier. When the power is
switched off, C5 immediately discharges through Diode CR1, grounding the input of the amplifier.
(TROUBLESHOOTING TIP) Check for proper operation of this circuit when experiencing excessive turn-
on or turn off “Pops”, or no output when signal applied to the input. Many times the JFET itself can be the
culprit. NOTE: Excessive turn-off “Pops” can also be caused by uneven discharge of the +/- power
supplies. Usually a mismatch in the Filter Capacitors will cause this problem. Its easy to look at both
supplies on an oscilloscope. Invert one scope input and check for even discharge to zero volts.
Q4 is the current source for the Differential Amplifier (Q2,Q3). For the Diff amp to work properly, one half
of the current from the current source must flow through each of the Diff amp legs. If the same amount of
current flows through each leg of the Diff amp, the voltage drop across resistors R14 & R15 must be the
same. If not, there will be a DC offset at the output of the amplifier. The overall gain of the amplifier is set
up around the Diff amp. R16 (27K) is the feedback resistor and R17 (1K) is the pull down resistor. Rfb
+Rpd ÷Rpd = Av. Therefore 27K + 1K ÷1K = 25K ÷1K = 28Av.
Q9 & Q10 make up a voltage amplification stage. Again, to operate properly, the same amount of current
must flow through these transistors. Thus the voltage drop across R20 & R21 must be the same. Diodes
CR16-CR19 (BYV26D) make up the Fixed Bias circuit for the output transistors. The body of the Diodes is
mounted through the heatsink to properly track the temperature of the transistors. These Diodes were
selected because they exhibit a 2mV decrease in Knee Voltage for every 1 degree (Celsius) increase in
temperature. The Collectors of Q9 & Q10 are at 0 volts. Therefore the Bias Diodes provide 2 voltage
drops (1.2 volts) to the Base of Driver Transistors Q13 & Q14. One Diode drop (0.6 volts) Biases on the
Driver Transistors. The remaining 0.6 volts drops across the output transistors (Q15-Q18) in parallel,
Biasing them on.
Transistors Q11, Q12 and associated components comprise the Current Limiting or Short Proof protection
circuit. There are usually two conditions which demand excessive output current from the amplifier. A
shorted speaker cable, or a load impedance which is below the minimum rating of the amplifier. If these
condition occur, the voltage drop across the Emitter Resistors (.33Ω5 Watt) will dramatically increase. On
the positive side of the amplifier, C11 charges through R29 & R34. On the negative side C12 charges
through R30 & R35. This will cause Q11 & Q12 to turn on. This limits the amount of signal which is
available to the Base of the Driver Transistors (Q13 & Q14). CR20-CR23 make up a latching circuit that
senses the signal through R22. This ensures that Q11 & Q12 turn on hard in conduction. When the fault
condition is removed from the output, the current limiting will remain latched up until the input signal is
removed.
Q12 & Q14 are the Driver Transistors for the output section. Q15-Q18 are the output transistors. Notice
on the schematic that the Base resistors carry the “Fp” designation. This indicates a Flame Proof/Fuse-

KXR 200
POWER AMPLIFIER (CONT)
Type resistor. They won’t burn and they won’t act like a fuse when exposed to an over-current condition.
This prevents catastrophic damage to the output section.. If an output transistor shorts Base to Collector or
Base to Emitter, the resistor will simply open. In many cases the amplifier will continue to operate, but at a
reduced power level. An increase in distortion may also become apparent. When replacing these
resistors, ALWAYS use the Fuse-Type OEM part.
PARTS LIST
PREAMP
PRINTED CIRCUIT BOARD ASSEMBLY
QTY PART # DESCRIPTION REFERENCE DESIGNATION
1 048497001 PCB ASSY KXR 200 PREAMP STUFFED
1 048914000 CABLE RIBBON 8 CKT 7 IN
1 048836000 CABLE RIBBON 12 CKT 23 IN
1 037943000 CAP AE RDL .33uF 50V C69
3 03869001 CAP AE AX 1.0uF 100V C6,20,34
4 026517001 CAP AE AX 2.2uF 50V C14,28,42,60
3 028459000 CAP AE RDL 2.2uF 50V 20% C61,66,72
2 038691001 CAP AE AX 4.7uF 50V C64,70
4 028463000 CAP AE RDL 10uF 50V 20% C12,26,40,58
10 025960001 CAP AE AX 22uF 16V C1,2,15,16,29,30,43,44,45,46
5 036954000 CAP AE RDL 22uF 63V 20% C13,27,41,59,78
1 028471000 CAP AE RDL 47uF 50V 20% C63
5 020909000 CAP CD 47PF 1000V 10% C62,65,67,71,73
8 025979000 CAP CD 50PF 1000V 10% C5,11,19,25,.33,39,49,57
8 038699001 CAP CA 100PF 100V C3,4,17,18,31,32,47,48
1 039262001 CAP CA 680PF 50V C76
1 039270001 CAP CA 10000PF 50V 5% LL C51
4 027256000 CAP MPF .0015uF 100V C9,23,37,55
1 027259000 CAP MPF .0033uF 100V C68
1 027261000 CAP MPF .0047uF 100V C53
3 027263000 CAP MPF .0082uF 100V C7,21,35
1 027265000 CAP MPF .015uF 100V C74
1 027267000 CAP MPF .022uF 100V C75
4 027275000 CAP MPF .068uF 100V C10,24,38,56
9 027278000 CAP MPF .1uF 63V 10% C54, 79-86
4 027281000 CAP MPF .22uF 63V C8,22,36,52
1 033477000 CAP MPF .68uF 63V 10% C50
11 031266000 CONTROL RTRY 50K B TAPER R20,22,44,46,68,70,98,99,110,116,118 (FX
SENDS, REVERB SEND, RETURNS,
MASTER VOLUME)
4 0249287000 CONTROL RTRY 50K 15A TAPER R17,41,65,95 (VOLUME CONTROLS)
13 033002000 CONTROL RTRY 50K CNTR DET B R7,10,13,31,34,37,55,58,61,82,85,88,91
(TONE CONTROLS)
15 016795000 IC DUAL OP AMP TL072 U1-15
2 030771000 JACK ¼ PCB 2/CD SCC J10,11 (FX SEND AND RETURN)
4 016917 JACK ¼ PCB 3/CD DCC J2,4,6,9 (CHANNEL INSERTS)
5 030987000 JACK ¼ PCB 3/CD DOC J1,3,5,8,12 (CHANNEL INPUTS, LINE OUT)
2 048466000 JACK RCA SINGLE PCB MOUNT J14,15
1 030762 JACK XLR FM PC VERT MT (A/D) J7 (CHANNEL 4 IC INPUT)
1 037249 JACK XLR MALE PC VERT MT J13 (LINE OUT)
73 020888001 JUMPER WIRE 22GA W1-73
1 028841 KNOB PUSH BUTTON MX/PX @S1
1 028097000 LED 5X5MM YLLOW SLB-55YY3 LD1
1 028039 LED RED 5X5 MM SLB-55VR3 LD2
1 048495 PCB FAB KXR 200 RAW PCB
3 024937 RES CF 1/4W 5% 10OHM LL R130,131,132
1 024942001 RES CF 1/4W 5% 22OHM LL R104
2 024947001 RES CF 1/4W 5% 47OHM R128,129
6 024965001 RES CF 1/4W 5% 1K LL R19,43,67,97,107,114
1 024967001 RES CF 1/4W 5% 1.2K LL R126

KXR 200
PREAMP
PRINTED CIRCUIT BOARD ASSEMBLY (CONT)
QTY PART # DESCRIPTION REFERENCE DESIGNATION
1 024969001 RES CF 1/4W 5% 1.5K LL R92
3 02497001 RES CF 1/4W 5% 1.8K LL R14,38,62
2 031819001 RES MF 1/4W 5% 1.82K LL R73,74
1 029005001 RES CF 1/4W 5% 2K LL R105
8 024971001 RES CF 1/4W 5% 2.2K LL R8,16,32,40,56,64,94,124
3 029455001 RES CF 1/4W 5% 2.4K LL R83,86,89
3 024972001 RES CF 1/4W 5% 2.7K LL R11,35,59
1 024973001 RES CF 1/4W 5% 3.3K LL R120
1 024978000 RES CF 1/4W 5% 5.5K LL R108
4 024981001 RES CF 1/4W 5% 10K LL R109,115,133,134
3 024983001 RES CF 1/4W 5% 12K LL R119,121,122
8 024986001 RES CF 1/4W 5% 18K LL R6,15,30,39,54,63,81,93
16 031818001 RES MF 1/4W 1% 18.2K LL R1,2,4,5,25,26,28,29,49,50,52,53,76,77,79,80
15 024987001 RES CF 1/4W 5% 22K LL R21,23,24,45,47,48,69,71,72,100-102,111,117,125
3 024993001 RES CF 1/4W 5% 47K LL R103,106,112
6 024996001 RES CF 1/4W 5% 82K LL R9,12,33,36,57,60
9 024997001 RES CF 1/4W 5% 100K LL R18,42,66,84,87,90,96,113,123
1 028861001 RES CF 1/2W 5% 3.3K LL R127
2 036375 SPACER RND NYL .147X.250X.720 @LD1-2
1 022904 SWITCH PB PC MT S1
POWER AMPLIFIER
PRINTED CIRCUIT BOARD ASSEMBLY
QTY PART # DESCRIPTION REFERENCE DESIGNATION
1 029779* BREAKER THERMAL NC OPEN 248 TS1
8 028459 CAP AE RDL 2.2UF 50V 20% C1,3,6,16-20
1 028460 CAP AE RDL 4.7uF 50V 20% C5
5 028471 CAP AE RDL 47uF 50V 20% C13,14,31,32,34
3 025787 CAP AE RDL MINI 100uF 16V NP C7,11-12
2 028494000 CAP AE RDL 100uF 35V 20% C25-26
2 028031 CAP AE RDL 3300uF 63V C22-23
1 033580000 CAP PFF RDL .0022uF 100V 10% C8
5 027278000 CAP MPF .1uF 63V 10% C9-10
1 024854000 CAP MPF RDL .1uF 400V 10% C15
1 041501 CAP MPF AX 2.2uF 100V 10% C33
7 064089001 DIODE 1N4003 LL CR38-41, 44-46
25 006260001 DIODE 1N4448 SIGNAL LL CR1-3,5-9,11-14,20,21,24,25,31-37,42,43
2 020534000 DIODE 1N5402 RECTIFER 200V C&F CR28,29
4 028776000 DIODE BIAS BYV26D LEAD FORMED CR16-19
4 025821001 DIODE HV FDH-400 SWITCHING LL CR10,15,26,27
1 027329001 DIODE ZEN 1N5228B 3.9V 5% LL CR30
2 027327001 DIODE ZEN 1N5234V 6.2V 5% LL CR22,23
1 031019001 DIODE ZEN 1N5245V .5W 15V 5% LL CR4
21 025802000 FSTN TAB MALE .250X.032 PCT MT CP1,2A,2B,3-16
2 025996000 FUSE CLIP PCB .250 & 5MM FUSE XF1
4 020775000 FUSE CLIP PCB 5VV XF2,3
1 090738000 FUSE QA 1-1/4X1/4 250V 6A F1 (100/120V ONLY)
1 020796 FUSE QA 20MMX5MM 250V 3.15A F1 (EXPORT 220/230/240V ONLY)
2 013112000 FUSE TD 20MMX5MM 250V 1A F2,3
1 027416000 HDR .1 CTR 8CKT SQ PIN P1A
1 048939000 HEATSINK BAR BXR/KXR 200 MAIN HEATSINK
2 025796000 HEATSINK TO-220 @U3,4
1 027404000 IC CA3080AE OTA U2
1 016795000 IC DUAL OP AMP TL072 U1
1 013562000 IC REGULATOR +15V MC7815CT U3
1 013564000 IC REGULATOR –15V MC7915CT U4
1 027387000 INDUCTOR AIR CORE RDL 2.5UH L1
4 038815000 INSULATOR SILICONE TO—3P @Q15-18
2 026043000 JUMPER WIRE 18GA .8X.175 JP1,2

KXR 200
POWER AMPLIFIER
PRINTED CIRCUIT BOARD ASSEMBLY (CONT)
QTY PART # DESCRIPTION REFERENCE DESIGNATION
27 020888001 JUMPER WIRE 22GA W1-27
1 048843001 PCB ASSY PWR AMP BXR 200 STUFFED
1 04884200 PCB FAB PWR AMP BXR 200 RAW PCB
4* 031693001 RES MF FUSE 1/4W 5% 4.7 OHM LL R36,37,40,41
2* 033205001 RES MF FUSE 1/4W 5% 15 OHM LL R27,28
1* 027749001 RES MF FUSE 1/4W 5% 22OHM LL R33
2 024947001 RES CF 1/4W 5% 47 OHM LL R10,11
1 024952001 RES CF 1/4W 5% 100OHM LL R4
2 024956001 RES CF 1/4W 5% 220OHM LL R20,21
2 024961001 RES CF 1/4W 5% 470OHM LL R29-30
1 024963001 RES CF 1/4W 5% 680OHM LL R67
8 024965001 RES CF 1/4W 5% 1K LL R5,8,17,22,24,25,49,64
7 024917001 RES CF 1/4W 5% 2.2K LL R14-15,18-19,34-35,60
1 024977001 RES CF 1/4W 5% 4.7K LL R51
5 025942001 RES CF 1/4W 5% 7.5K LL R12,52-55
6 024981001 RES CF 1/4W 5% 10K LL R3,47,50,57-58,61
2 024985001 RES CF 1/4W 5% 15K LL R13,65
1 024987001 RES CF 1/4W 5% 22K LL R1
4 024988001 RES CF 1/4W 5% 27K LL R9,16,31,32
1 024989001 RES CF 1/4W 5% 33K LL R2
5 024997001 RES CF 1/4W 5% 100K LL R56,59,62,63,66
1 024998001 RES CF 1/4W 5% 120K LL R48
2 025069001 RES CF 1/4W 5% 1M LL R6,7
1 028029001 RES FILM 1W 5% 1.5K LL R73
1 027627001 RES FILM 1W 5% 10OHM LL R44
2 036621001 RES CF 1W 5% 6.8K LL R23,26
2 027628000 RES FILM 2W 5% 47OHM R45,46
4 032958000 RES WW BT 5W 10% .33OHM R38-39,42-43
1 048467 RES WW BT 5W 10% 39OHM R72
1 048468 RES WW BT 10W 10% 47OHM R71
2 041595000 SCRW 6-32X3/16 PHP STL ZI SEMS @TS1
5 027638000 SCRW TF 4-40X3/8 HWHS ZI .1 “HD @Q13-18, U3,4
5 032908000 SCRW TF 6-32X3/8 PHP ZI PCB TO HEATSINK MOUNT
1 026411000 THERMISTER 2.5 OHM 8A C30-19 TH1
1 014689000 XSTR N-CH JFET J111 TO-92 Q1
3 016739000 XSTR NPN 2N4401 TO-92 Q11,20,21
4 02575100 XSTR NP 2SC2362K/2SC2389 Q2-4,8
2 028763000 XSTR NPN 2SC3281 TOP-3L Q15,17
1 028760000 XSTR NPN 2SC3298A TOP-220 Q13
1 014867000 XSTR NPN MPSW10 TO-226AE Q10
2 016742000 XSTR PNP 2N4403 TO-92 Q12,22
3 025752000 XSTR PNP 2SA1016K TO-92 Q5-7
2 028762000 XSTR PNP 2SA1302 TOP-3L Q16,18
1 028759000 XSTR PNP 2SA1306A0 TOP-220 Q14
1 014408000 XSTR PNP DRLNGTN MPSA63 TO-92 Q19
1 014866000 XSTR PNP MPSW92 TO-226AE Q9
CHASSIS ASSEMBLY
QTY PART # DESCRIPTION REFERENCE DESIGNATION
1 048505000 CHS ASSY KXR 200 120V
1 00756500 BUSHING SR .625X.125X37/64 BLK @ PWR CABLE 100/120V ONLY
1 010401 BUSHING SR .625X.125X37/64 WHT @ PWR CABLE 230/240V ONLY
1 026541000 CABLE ASSY PRW W/.250 TAB 120V POWER CABLE 120V ONLY
1 048463 CABLE ASSY PWR .250 TAB 100V POWER CABLE 100V ONLY
1 033331 CABLE ASSY PWR 220/240V POWER CABLE 230V ONLY
1 038602 CABLE ASSY PWR AUST .250 TAB PWR CABLE AUSTRALIA 240V
1 040993 CABLE ASSY PWR 5A U.K. .250 TAB P CABLE UNITED KINGDOM 240V
1 047524000 CAP ASSY .1UF 400V Q/RECP/TAB @BRIDGE RECTIFIER EMI SUPPRESSION
1 024854000 CAP MPF RDL .1UF 400V 10% RAW CAP FOR ABOVE ASSEMBLY
1 048499000 CHS KXR 200
1 032925000 DIODE BRIDGE RECTIFIER

KXR 200
CHASSIS ASSEMBLY (CONT)
QTY PART # DESCRIPTION REFERENCE DESIGNATION
1 048971000 HEAT SINK EXTRUDED BXR 200
28 048835000 KNOB CTL SUCTOM DBL BLK/OFFWHT
2 069393000 NUT 6-32 HEX EXT LOCK GROUND LUG MOUNT
1 022004000 NUT KEPS #8-32 ZINC BRIDGE RECTIFIER MOUNT
1 048500000 PANEL FRONT KXR 200
1 048501000 PANEL REAR KXR 200
2 047523000 RECEPTACLE W/TAB .250 18-14 GA
6 017716000 SCREW M 8-32X1/2 PHP BLX HATSINK TO CHASSIS MOUNT
4 037568000 SCREW M 6-32X3/4 PHP ZI LW PWR AMP PCB MNT
2 039367000 SCREW M 6-32X3/8 PHPS SS ITLW PREAMP PCB MOUNT
4 031184000 SCREW M 6-32X1/4 PHPS BLX ITLW SHIELD MOUNT
2 031868000 SCREW PLASTITE 4X1/4 PHP BLX FEMALE XLR MOUNT (FRONT)
2 037990000 SCREW PLASTITE 6X3/5 PHP BLX MALE XLR MOUNT (REAR)
4 037997000 SCREW TF 10-32X5/8 HWHS BLX TRANSFORMER MOUNT
5 027636000 SCREW TF 8-32X5/8 HWH BLX HEATSINK TO TRANSISTOR BAR
1 049524000 SHIELD KXR 200 @ PREAMP
4 031241000 STANDOFF HX M/F AL 6-32X3/8 SHIELD MOUNT
1 040582000 SWITCH DPST .250 TAB GLOBAL POWER SWITCH
1 048960000 XFMR DOMESTIC BXR 200 T1 (120V DOMESTIC ONLY)
1 041122 XFMR PWR EXPORT T1 (100/120/230V)
CABINET ASSEMBLY
QTY PART # DESCRIPTION REFERENCE DESIGNATION
1 048498000 CAB ASSY KXR 200 ENTIRE CABINET
1 047120000 CABLE REVERB 1450MM
4 023513000 CASTER SWIVEL
0.48 026317000 CLOTH GRILLE BLACK PVC
6 031867000 CORNER 2 HOLE W/ NOTCH BLK PWDR FRONT AND TOP/REAR
2 03184000 CORNER 3 HOLE BLK PWDRD BOTTOM/REAR
4 029821000 EYELET RFLNGD .215ODX.315L REVER PAN MOUNT
2 049564000 GASKET HANDLE
1 02888500 GASKET HORN DUAL PIEZO
4 02784900 GLIDE CAB 1.24X.335 BLX WAX STEEL ONLY
1 048498001 GRILLE ASSY KXR 200 COMPLETE GRILLE
2 048958000 HANDLE RECESSED KXR/BXR
1 028813000 HORN DUAL PIEZO (ADD 028885) COMPLETE HORN)
4 019275000 INSERT GLIDE CUSHION 1.27 DIA RUBBER ONLY
4 023505000 MTG PLATE – SWIVEL CASTER CASTER SOCKET
1 011298000 NAMEPLATE FENDER SMALL LOGO
8 021972000 NUT T 10-32X3/4 STR 3 PRNG BLX SPEAKER MOUNT
1 028055000 REVERB UNIT 800 OHM 8EB2C1B DN REVERB PAN
REF 026570000 TOLEX BLACK LT WEIGHT
6 029527000 WSHR FNSH 8-5/8 FLNGD BLX WX CHASSIS MOUNT
MISCELLANEOUS
QTY PART # DESCRIPTION REFERENCE DESIGNATION
048502000 MANUAL OWNER KXR 200
048493 SCHEM REDU W/SVC KXR200 PRE PREAMP
048840 SCHEM REDU W/SVC PA BXR/KXR 200 POWER AMPLIFIER